[U-Boot] [PATCH 07/26] mpc8xx: remove R360MPI board support

[Masahiro Yamada <yamada.m@jp.panasonic.com>]

This board is still a non-generic board.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
---

 arch/powerpc/cpu/mpc8xx/Kconfig    |   4 -
 arch/powerpc/cpu/mpc8xx/cpu_init.c |   1 -
 board/r360mpi/Kconfig              |   9 -
 board/r360mpi/MAINTAINERS          |   6 -
 board/r360mpi/Makefile             |   8 -
 board/r360mpi/flash.c              | 468 -------------------------------------
 board/r360mpi/pcmcia.c             | 232 ------------------
 board/r360mpi/r360mpi.c            | 403 --------------------------------
 board/r360mpi/u-boot.lds           |  89 -------
 configs/R360MPI_defconfig          |   3 -
 doc/README.scrapyard               |   1 +
 drivers/video/mpc8xx_lcd.c         |  25 --
 include/commproc.h                 |   4 -
 include/configs/R360MPI.h          | 464 ------------------------------------
 include/pcmcia.h                   |   2 -
 15 files changed, 1 insertion(+), 1718 deletions(-)
 delete mode 100644 board/r360mpi/Kconfig
 delete mode 100644 board/r360mpi/MAINTAINERS
 delete mode 100644 board/r360mpi/Makefile
 delete mode 100644 board/r360mpi/flash.c
 delete mode 100644 board/r360mpi/pcmcia.c
 delete mode 100644 board/r360mpi/r360mpi.c
 delete mode 100644 board/r360mpi/u-boot.lds
 delete mode 100644 configs/R360MPI_defconfig
 delete mode 100644 include/configs/R360MPI.h

diff --git a/arch/powerpc/cpu/mpc8xx/Kconfig b/arch/powerpc/cpu/mpc8xx/Kconfig
index 37ee5f6..4e67ff2 100644
--- a/arch/powerpc/cpu/mpc8xx/Kconfig
+++ b/arch/powerpc/cpu/mpc8xx/Kconfig
@@ -28,9 +28,6 @@ config TARGET_LWMON
 config TARGET_NETVIA
 	bool "Support NETVIA"
 
-config TARGET_R360MPI
-	bool "Support R360MPI"
-
 config TARGET_TQM823L
 	bool "Support TQM823L"
 
@@ -75,7 +72,6 @@ source "board/ip860/Kconfig"
 source "board/ivm/Kconfig"
 source "board/lwmon/Kconfig"
 source "board/netvia/Kconfig"
-source "board/r360mpi/Kconfig"
 source "board/tqc/tqm8xx/Kconfig"
 
 endmenu
diff --git a/arch/powerpc/cpu/mpc8xx/cpu_init.c b/arch/powerpc/cpu/mpc8xx/cpu_init.c
index f772787..9350fdd 100644
--- a/arch/powerpc/cpu/mpc8xx/cpu_init.c
+++ b/arch/powerpc/cpu/mpc8xx/cpu_init.c
@@ -129,7 +129,6 @@ void cpu_init_f (volatile immap_t * immr)
     defined(CONFIG_IVML24)	|| \
     defined(CONFIG_IVMS8)	|| \
     defined(CONFIG_LWMON)	|| \
-    defined(CONFIG_R360MPI)	|| \
     defined(CONFIG_RMU)
 
 	memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM;
diff --git a/board/r360mpi/Kconfig b/board/r360mpi/Kconfig
deleted file mode 100644
index fe8484f..0000000
--- a/board/r360mpi/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_R360MPI
-
-config SYS_BOARD
-	default "r360mpi"
-
-config SYS_CONFIG_NAME
-	default "R360MPI"
-
-endif
diff --git a/board/r360mpi/MAINTAINERS b/board/r360mpi/MAINTAINERS
deleted file mode 100644
index a67ab0c..0000000
--- a/board/r360mpi/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-R360MPI BOARD
-M:	Wolfgang Denk <wd@denx.de>
-S:	Maintained
-F:	board/r360mpi/
-F:	include/configs/R360MPI.h
-F:	configs/R360MPI_defconfig
diff --git a/board/r360mpi/Makefile b/board/r360mpi/Makefile
deleted file mode 100644
index f8f7fe7..0000000
--- a/board/r360mpi/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= r360mpi.o flash.o pcmcia.o
diff --git a/board/r360mpi/flash.c b/board/r360mpi/flash.c
deleted file mode 100644
index 996a22e..0000000
--- a/board/r360mpi/flash.c
+++ /dev/null
@@ -1,468 +0,0 @@
-/*
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris at nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* #define DEBUG */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips    */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef  CONFIG_ENV_ADDR
-#  define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef  CONFIG_ENV_SIZE
-#  define CONFIG_ENV_SIZE	CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef  CONFIG_ENV_SECT_SIZE
-#  define CONFIG_ENV_SECT_SIZE  CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Protection Flags:
- */
-#define FLAG_PROTECT_SET	0x01
-#define FLAG_PROTECT_CLEAR	0x02
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH16
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH	ushort
-#define FLASH_PORT_WIDTHV	vu_short
-#else
-#define FLASH_PORT_WIDTH	ulong
-#define FLASH_PORT_WIDTHV	vu_long
-#endif
-
-#define FPW			FLASH_PORT_WIDTH
-#define FPWV			FLASH_PORT_WIDTHV
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPW * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	unsigned long size_b0;
-	int i;
-
-	/* Init: no FLASHes known */
-	for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
-		flash_info[i].flash_id = FLASH_UNKNOWN;
-	}
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-	size_b0 = flash_get_size ((FPW *) FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size_b0, size_b0 << 20);
-	}
-
-	/* Remap FLASH according to real size */
-	memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size_b0 & 0xFFFF8000);
-	memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_MS_GPCM | BR_V;
-
-	/* Re-do sizing to get full correct info */
-	size_b0 = flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-	flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
-	/* monitor protection ON by default */
-	(void) flash_protect (FLAG_PROTECT_SET,
-				CONFIG_SYS_FLASH_BASE,
-				CONFIG_SYS_FLASH_BASE + monitor_flash_len - 1,
-				&flash_info[0]);
-#endif
-
-#ifdef	CONFIG_ENV_IS_IN_FLASH
-	/* ENV protection ON by default */
-	flash_protect (FLAG_PROTECT_SET,
-			CONFIG_ENV_ADDR,
-			CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
-			&flash_info[0]);
-#endif
-
-	flash_info[0].size = size_b0;
-
-	return (size_b0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return;
-	}
-
-	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
-		for (i = 0; i < info->sector_count; i++) {
-			info->start[i] = base + (i * 0x00020000);
-		}
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_INTEL:
-		printf ("INTEL ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	switch (info->flash_id & FLASH_TYPEMASK) {
-	case FLASH_28F320J3A:
-		printf ("28F320J3A\n");
-		break;
-	case FLASH_28F640J3A:
-		printf ("28F640J3A\n");
-		break;
-	case FLASH_28F128J3A:
-		printf ("28F128J3A\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld MB in %d Sectors\n",
-			info->size >> 20, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s",
-			info->start[i],
-			info->protect[i] ? " (RO)" : "     ");
-	}
-	printf ("\n");
-	return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (FPW * addr, flash_info_t * info)
-{
-	FPW value;
-
-	/* Make sure Block Lock Bits get cleared */
-	addr[0] = (FPW) 0x00FF00FF;
-	addr[0] = (FPW) 0x00600060;
-	addr[0] = (FPW) 0x00D000D0;
-	addr[0] = (FPW) 0x00FF00FF;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr[0x5555] = (FPW) 0x00AA00AA;
-	addr[0x2AAA] = (FPW) 0x00550055;
-	addr[0x5555] = (FPW) 0x00900090;
-
-	value = addr[0];
-
-	debug("Manuf. ID @ 0x%08lx: 0x%08x\n", (ulong)addr, value);
-
-	switch (value) {
-	case (FPW) INTEL_MANUFACT:
-		info->flash_id = FLASH_MAN_INTEL;
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-		return (0);			/* no or unknown flash  */
-	}
-
-	value = addr[1];			/* device ID        */
-
-	debug("Device ID @ 0x%08lx: 0x%08x\n", (ulong)(&addr[1]), value);
-
-	switch (value) {
-	case (FPW) INTEL_ID_28F320J3A:
-		info->flash_id += FLASH_28F320J3A;
-		info->sector_count = 32;
-		info->size = 0x00400000;
-		break;				/* => 4 MB     */
-
-	case (FPW) INTEL_ID_28F640J3A:
-		info->flash_id += FLASH_28F640J3A;
-		info->sector_count = 64;
-		info->size = 0x00800000;
-		break;				/* => 8 MB     */
-
-	case (FPW) INTEL_ID_28F128J3A:
-		info->flash_id += FLASH_28F128J3A;
-		info->sector_count = 128;
-		info->size = 0x01000000;
-		break;				/* => 16 MB     */
-
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		break;
-	}
-
-	if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
-		printf ("** ERROR: sector count %d > max (%d) **\n",
-				info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
-		info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
-	}
-
-	addr[0] = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	int flag, prot, sect;
-	ulong type, start, now, last;
-	int rcode = 0;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	type = (info->flash_id & FLASH_VENDMASK);
-	if ((type != FLASH_MAN_INTEL)) {
-		printf ("Can't erase unknown flash type %08lx - aborted\n",
-			info->flash_id);
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n",
-			prot);
-	} else {
-		printf ("\n");
-	}
-
-	start = get_timer (0);
-	last = start;
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			FPWV *addr = (FPWV *) (info->start[sect]);
-			FPW status;
-
-			/* Disable interrupts which might cause a timeout here */
-			flag = disable_interrupts ();
-
-			*addr = (FPW) 0x00500050;	/* clear status register */
-			*addr = (FPW) 0x00200020;	/* erase setup */
-			*addr = (FPW) 0x00D000D0;	/* erase confirm */
-
-			/* re-enable interrupts if necessary */
-			if (flag)
-				enable_interrupts ();
-
-			/* wait at least 80us - let's wait 1 ms */
-			udelay (1000);
-
-			while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-			    if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-				printf ("Timeout\n");
-				*addr = (FPW) 0x00B000B0;	/* suspend erase     */
-				*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
-				rcode = 1;
-				break;
-			    }
-
-			    /* show that we're waiting */
-			    if ((now - last) > 1000) {	/* every second */
-				putc ('.');
-				last = now;
-			    }
-			}
-
-			*addr = (FPW) 0x00FF00FF;	/* reset to read mode */
-		}
-	}
-	printf (" done\n");
-	return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp;
-	FPW data;
-
-	int i, l, rc, port_width;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		return 4;
-	}
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
-	wp = (addr & ~1);
-	port_width = 2;
-#else
-	wp = (addr & ~3);
-	port_width = 4;
-#endif
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < port_width && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < port_width; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_data (info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= port_width) {
-		data = 0;
-		for (i = 0; i < port_width; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_data (info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += port_width;
-		cnt -= port_width;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < port_width; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_data (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
-	FPWV *addr = (FPWV *) dest;
-	ulong status;
-	ulong start;
-	int flag;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*addr & data) != data) {
-		printf ("not erased@%08lx (%x)\n", (ulong) addr, *addr);
-		return (2);
-	}
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	*addr = (FPW) 0x00400040;	/* write setup */
-	*addr = data;
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts ();
-
-	start = get_timer (0);
-
-	while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
-		if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-			*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-			return (1);
-		}
-	}
-
-	*addr = (FPW) 0x00FF00FF;	/* restore read mode */
-
-	return (0);
-}
diff --git a/board/r360mpi/pcmcia.c b/board/r360mpi/pcmcia.c
deleted file mode 100644
index a939b31..0000000
--- a/board/r360mpi/pcmcia.c
+++ /dev/null
@@ -1,232 +0,0 @@
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-
-#undef	CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define	CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define	CONFIG_PCMCIA
-#endif
-
-#ifdef	CONFIG_PCMCIA
-
-#define PCMCIA_BOARD_MSG "R360MPI"
-
-int pcmcia_hardware_enable(int slot)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	volatile sysconf8xx_t	*sysp;
-	uint reg, mask;
-
-	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	udelay(10000);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-	sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
-	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
-	/*
-	* Configure SIUMCR to enable PCMCIA port B
-	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
-	*/
-	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
-
-	/* clear interrupt state, and disable interrupts */
-	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
-	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
-	/*
-	* Disable interrupts, DMA, and PCMCIA buffers
-	* (isolate the interface) and assert RESET signal
-	*/
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	* Configure Ports A, B & C pins for
-	* 5 Volts Enable and 3 Volts enable
-	*/
-	immap->im_ioport.iop_pcpar &= ~(0x0400);
-	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
-	immap->im_ioport.iop_pcdir |= 0x0400;*/
-
-	immap->im_ioport.iop_papar &= ~(0x0200);/*
-	immap->im_ioport.iop_padir |= 0x0200;*/
-#if 0
-	immap->im_ioport.iop_pbpar &= ~(0xC000);
-	immap->im_ioport.iop_pbdir &= ~(0xC000);
-#endif
-	/* remove all power */
-
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	/*
-	* Make sure there is a card in the slot, then configure the interface.
-	*/
-	udelay(10000);
-	debug ("[%d] %s: PIPR(%p)=0x%x\n",
-	       __LINE__,__FUNCTION__,
-	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
-	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
-		printf ("   No Card found\n");
-		return (1);
-	}
-
-	/*
-	* Power On.
-	*/
-	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
-	reg  = pcmp->pcmc_pipr;
-	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
-	       reg,
-	       (reg&PCMCIA_VS1(slot))?"n":"ff",
-	       (reg&PCMCIA_VS2(slot))?"n":"ff");
-	if ((reg & mask) == mask) {
-		immap->im_ioport.iop_pcdat &= ~(0x4000);
-		puts (" 5.0V card found: ");
-	} else {
-		immap->im_ioport.iop_padat &= ~(0x0002);
-		puts (" 3.3V card found: ");
-	}
-	immap->im_ioport.iop_pcdir |= 0x0400;
-	immap->im_ioport.iop_padir |= 0x0200;
-#if 0
-	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
-	cp->cp_pbdir &= ~(0x0020 | 0x0010);
-	cp->cp_pbpar &= ~(0x0020 | 0x0010);
-	udelay(500000);
-#endif
-	debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(250000);	/* some cards need >150 ms to come up :-( */
-
-	debug ("# hardware_enable done\n");
-
-	return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
-	volatile immap_t	*immap;
-	u_long reg;
-
-	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-
-	/* remove all power */
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	/* Configure PCMCIA General Control Register */
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = 0;
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-
-	udelay(10000);
-
-	return (0);
-}
-#endif
-
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
-	volatile immap_t	*immap;
-	volatile pcmconf8xx_t	*pcmp;
-	u_long reg;
-
-	debug ("voltage_set: "
-			PCMCIA_BOARD_MSG
-			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
-	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
-	immap = (immap_t *)CONFIG_SYS_IMMR;
-	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-	/*
-	* Disable PCMCIA buffers (isolate the interface)
-	* and assert RESET signal
-	*/
-	debug ("Disable PCMCIA buffers and assert RESET\n");
-	reg  = PCMCIA_PGCRX(_slot_);
-	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	/*
-	* Configure Ports A & C pins for
-	* 5 Volts Enable and 3 Volts enable,
-	* Turn off all power
-	*/
-	debug ("PCMCIA power OFF\n");
-	immap->im_ioport.iop_pcpar &= ~(0x0400);
-	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
-	immap->im_ioport.iop_pcdir |= 0x0400;*/
-
-	immap->im_ioport.iop_papar &= ~(0x0200);/*
-	immap->im_ioport.iop_padir |= 0x0200;*/
-
-	immap->im_ioport.iop_pcdat |= 0x0400;
-	immap->im_ioport.iop_padat |= 0x0200;
-
-	reg = 0;
-	switch(vcc) {
-		case  0:		break;
-		case 33: reg |= 0x0200;	break;
-		case 50: reg |= 0x0400;	break;
-		default:		goto done;
-	}
-
-	/* Checking supported voltages */
-
-	debug ("PIPR: 0x%x --> %s\n",
-	       pcmp->pcmc_pipr,
-	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
-	if (reg & 0x0200)
-		immap->im_ioport.iop_pcdat &= !reg;
-	if (reg & 0x0400)
-		immap->im_ioport.iop_padat &= !reg;
-	immap->im_ioport.iop_pcdir |= 0x0200;
-	immap->im_ioport.iop_padir |= 0x0400;
-	if (reg) {
-		debug ("PCMCIA powered at %sV\n",
-		       (reg&0x0400) ? "5.0" : "3.3");
-	} else {
-		debug ("PCMCIA powered down\n");
-	}
-
-done:
-			debug ("Enable PCMCIA buffers and stop RESET\n");
-	reg  =  PCMCIA_PGCRX(_slot_);
-	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
-	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
-	PCMCIA_PGCRX(_slot_) = reg;
-	udelay(500);
-
-	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
-	       slot+'A');
-	return (0);
-}
-
-#endif	/* CCONFIG_PCMCIA */
diff --git a/board/r360mpi/r360mpi.c b/board/r360mpi/r360mpi.c
deleted file mode 100644
index d06aea7..0000000
--- a/board/r360mpi/r360mpi.c
+++ /dev/null
@@ -1,403 +0,0 @@
-/*
- * (C) Copyright 2001-2003
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <config.h>
-#include <mpc8xx.h>
-#include <i2c.h>
-
-#include <commproc.h>
-#include <command.h>
-#include <malloc.h>
-
-#include <linux/types.h>
-#include <linux/string.h>       /* for strdup */
-
-
-/*
- *  Memory Controller Using
- *
- *  CS0 - Flash memory		(0x40000000)
- *  CS1 - FLASH memory		(0x????????)
- *  CS2 - SDRAM			(0x00000000)
- *  CS3 -
- *  CS4 -
- *  CS5 -
- *  CS6 - PCMCIA device
- *  CS7 - PCMCIA device
- */
-
-/* ------------------------------------------------------------------------- */
-
-#define _not_used_	0xffffffff
-
-const uint sdram_table[]=
-{
-	/* single read. (offset 0 in upm RAM) */
-	0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
-	0x1ff77c47,
-
-	/* MRS initialization (offset 5) */
-
-	0x1ff77c34, 0xefeabc34, 0x1fb57c35,
-
-	/* burst read. (offset 8 in upm RAM) */
-	0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
-	0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-
-	/* single write. (offset 18 in upm RAM) */
-	0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-
-	/* burst write. (offset 20 in upm RAM) */
-	0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
-	0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-
-	/* refresh. (offset 30 in upm RAM) */
-	0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
-	0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
-	_not_used_, _not_used_, _not_used_, _not_used_,
-
-	/* exception. (offset 3c in upm RAM) */
-	0x7ffffc07, _not_used_, _not_used_, _not_used_ };
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
-	puts ("Board: R360 MPI Board\n");
-	return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	long int size8, size9;
-	long int size_b0 = 0;
-	unsigned long reg;
-
-	upmconfig (UPMA, (uint *) sdram_table,
-			   sizeof (sdram_table) / sizeof (uint));
-
-	/*
-	 * Preliminary prescaler for refresh (depends on number of
-	 * banks): This value is selected for four cycles every 62.4 us
-	 * with two SDRAM banks or four cycles every 31.2 us with one
-	 * bank. It will be adjusted after memory sizing.
-	 */
-	memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
-	memctl->memc_mar = 0x00000088;
-
-	/*
-	 * Map controller bank 2 to the SDRAM bank at
-	 * preliminary address - these have to be modified after the
-	 * SDRAM size has been determined.
-	 */
-	memctl->memc_or2 = CONFIG_SYS_OR2_PRELIM;
-	memctl->memc_br2 = CONFIG_SYS_BR2_PRELIM;
-
-	memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE));	/* no refresh yet */
-
-	udelay (200);
-
-	/* perform SDRAM initializsation sequence */
-
-	memctl->memc_mcr = 0x80004105;	/* SDRAM bank 0 */
-	udelay (200);
-	memctl->memc_mcr = 0x80004230;	/* SDRAM bank 0 - execute twice */
-	udelay (200);
-
-	memctl->memc_mamr |= MAMR_PTAE;	/* enable refresh */
-
-	udelay (1000);
-
-	/*
-	 * Check Bank 2 Memory Size for re-configuration
-	 *
-	 * try 8 column mode
-	 */
-	size8 = dram_size (CONFIG_SYS_MAMR_8COL, (long *) SDRAM_BASE2_PRELIM,
-					   SDRAM_MAX_SIZE);
-
-	udelay (1000);
-
-	/*
-	 * try 9 column mode
-	 */
-	size9 = dram_size (CONFIG_SYS_MAMR_9COL, (long *) SDRAM_BASE2_PRELIM,
-					   SDRAM_MAX_SIZE);
-
-	if (size8 < size9) {		/* leave configuration@9 columns */
-		size_b0 = size9;
-/*	debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20);	*/
-	} else {			/* back to 8 columns            */
-		size_b0 = size8;
-		memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
-		udelay (500);
-/*	debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20);	*/
-	}
-
-	udelay (1000);
-
-	/*
-	 * Adjust refresh rate depending on SDRAM type, both banks
-	 * For types > 128 MBit leave it at the current (fast) rate
-	 */
-	if ((size_b0 < 0x02000000)) {
-		/* reduce to 15.6 us (62.4 us / quad) */
-		memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
-		udelay (1000);
-	}
-
-	/*
-	 * Final mapping
-	 */
-
-	memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
-	memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
-	/* adjust refresh rate depending on SDRAM type, one bank */
-	reg = memctl->memc_mptpr;
-	reg >>= 1;		/* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
-	memctl->memc_mptpr = reg;
-
-	udelay (10000);
-
-#ifdef CONFIG_CAN_DRIVER
-	/* Initialize OR3 / BR3 */
-	memctl->memc_or3 = CONFIG_SYS_OR3_CAN;		/* switch GPLB_5 to GPLA_5 */
-	memctl->memc_br3 = CONFIG_SYS_BR3_CAN;
-
-	/* Initialize MBMR */
-	memctl->memc_mbmr = MBMR_GPL_B4DIS;	/* GPL_B4 works as UPWAITB */
-
-	/* Initialize UPMB for CAN: single read */
-	memctl->memc_mdr = 0xFFFFC004;
-	memctl->memc_mcr = 0x0100 | UPMB;
-
-	memctl->memc_mdr = 0x0FFFD004;
-	memctl->memc_mcr = 0x0101 | UPMB;
-
-	memctl->memc_mdr = 0x0FFFC000;
-	memctl->memc_mcr = 0x0102 | UPMB;
-
-	memctl->memc_mdr = 0x3FFFC004;
-	memctl->memc_mcr = 0x0103 | UPMB;
-
-	memctl->memc_mdr = 0xFFFFDC05;
-	memctl->memc_mcr = 0x0104 | UPMB;
-
-	/* Initialize UPMB for CAN: single write */
-	memctl->memc_mdr = 0xFFFCC004;
-	memctl->memc_mcr = 0x0118 | UPMB;
-
-	memctl->memc_mdr = 0xCFFCD004;
-	memctl->memc_mcr = 0x0119 | UPMB;
-
-	memctl->memc_mdr = 0x0FFCC000;
-	memctl->memc_mcr = 0x011A | UPMB;
-
-	memctl->memc_mdr = 0x7FFCC004;
-	memctl->memc_mcr = 0x011B | UPMB;
-
-	memctl->memc_mdr = 0xFFFDCC05;
-	memctl->memc_mcr = 0x011C | UPMB;
-#endif
-
-	return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value,
-			   long int *base, long int maxsize)
-{
-	volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
-	volatile memctl8xx_t *memctl = &immap->im_memctl;
-
-	memctl->memc_mamr = mamr_value;
-
-	return (get_ram_size(base, maxsize));
-}
-
-/* ------------------------------------------------------------------------- */
-
-void r360_i2c_lcd_write (uchar data0, uchar data1)
-{
-	if (i2c_write (CONFIG_SYS_I2C_LCD_ADDR, data0, 1, &data1, 1)) {
-		printf("Can't write lcd data 0x%02X 0x%02X.\n", data0, data1);
-	}
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*-----------------------------------------------------------------------
- * Keyboard Controller
- */
-
-/* Number of bytes returned from Keyboard Controller */
-#define KEYBD_KEY_MAX	16				/* maximum key number */
-#define KEYBD_DATALEN	((KEYBD_KEY_MAX + 7) / 8)	/* normal key scan data */
-
-static uchar *key_match (uchar *);
-
-int misc_init_r (void)
-{
-	char kbd_data[KEYBD_DATALEN];
-	char keybd_env[2 * KEYBD_DATALEN + 1];
-	char *str;
-	int i;
-
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
-	i2c_read (CONFIG_SYS_I2C_KEY_ADDR, 0, 0, (uchar *)kbd_data, KEYBD_DATALEN);
-
-	for (i = 0; i < KEYBD_DATALEN; ++i) {
-		sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
-	}
-	setenv ("keybd", keybd_env);
-
-	str = strdup ((char *)key_match ((uchar *)keybd_env));	/* decode keys */
-
-#ifdef CONFIG_PREBOOT	/* automatically configure "preboot" command on key match */
-	setenv ("preboot", str);	/* set or delete definition */
-#endif /* CONFIG_PREBOOT */
-	if (str != NULL) {
-		free (str);
-	}
-
-	return (0);
-}
-
-/*-----------------------------------------------------------------------
- * Check if pressed key(s) match magic sequence,
- * and return the command string associated with that key(s).
- *
- * If no key press was decoded, NULL is returned.
- *
- * Note: the first character of the argument will be overwritten with
- * the "magic charcter code" of the decoded key(s), or '\0'.
- *
- *
- * Note: the string points to static environment data and must be
- * saved before you call any function that modifies the environment.
- */
-#ifdef CONFIG_PREBOOT
-
-static uchar kbd_magic_prefix[] = "key_magic";
-static uchar kbd_command_prefix[] = "key_cmd";
-
-static uchar *key_match (uchar * kbd_str)
-{
-	uchar magic[sizeof (kbd_magic_prefix) + 1];
-	uchar cmd_name[sizeof (kbd_command_prefix) + 1];
-	uchar *str, *suffix;
-	uchar *kbd_magic_keys;
-	char *cmd;
-
-	/*
-	 * The following string defines the characters that can pe appended
-	 * to "key_magic" to form the names of environment variables that
-	 * hold "magic" key codes, i. e. such key codes that can cause
-	 * pre-boot actions. If the string is empty (""), then only
-	 * "key_magic" is checked (old behaviour); the string "125" causes
-	 * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
-	 */
-	if ((kbd_magic_keys = (uchar *)getenv ("magic_keys")) != NULL) {
-		/* loop over all magic keys;
-		 * use '\0' suffix in case of empty string
-		 */
-		for (suffix = kbd_magic_keys;
-		     *suffix || suffix == kbd_magic_keys;
-		     ++suffix) {
-			sprintf ((char *)magic, "%s%c", kbd_magic_prefix, *suffix);
-
-#if 0
-			printf ("### Check magic \"%s\"\n", magic);
-#endif
-
-			if ((str = (uchar *)getenv ((char *)magic)) != 0) {
-
-#if 0
-				printf ("### Compare \"%s\" \"%s\"\n",
-					kbd_str, str);
-#endif
-				if (strcmp ((char *)kbd_str, (char *)str) == 0) {
-					sprintf ((char *)cmd_name, "%s%c",
-						 kbd_command_prefix,
-						 *suffix);
-
-					if ((cmd = getenv ((char *)cmd_name)) != 0) {
-#if 0
-						printf ("### Set PREBOOT to $(%s): \"%s\"\n",
-							cmd_name, cmd);
-#endif
-						return ((uchar *)cmd);
-					}
-				}
-			}
-		}
-	}
-#if 0
-	printf ("### Delete PREBOOT\n");
-#endif
-	*kbd_str = '\0';
-	return (NULL);
-}
-#endif	/* CONFIG_PREBOOT */
-
-/* Read Keyboard status */
-int do_kbd (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[])
-{
-	uchar kbd_data[KEYBD_DATALEN];
-	uchar keybd_env[2 * KEYBD_DATALEN + 1];
-	int i;
-
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-
-	/* Read keys */
-	i2c_read (CONFIG_SYS_I2C_KEY_ADDR, 0, 0, kbd_data, KEYBD_DATALEN);
-
-	puts ("Keys:");
-	for (i = 0; i < KEYBD_DATALEN; ++i) {
-		sprintf ((char *)(keybd_env + i + i), "%02X", kbd_data[i]);
-		printf (" %02x", kbd_data[i]);
-	}
-	putc ('\n');
-	setenv ("keybd", (char *)keybd_env);
-	return 0;
-}
-
-U_BOOT_CMD(
-	kbd,	1,	1,	do_kbd,
-	"read keyboard status",
-	""
-);
diff --git a/board/r360mpi/u-boot.lds b/board/r360mpi/u-boot.lds
deleted file mode 100644
index 5f69bc4..0000000
--- a/board/r360mpi/u-boot.lds
+++ /dev/null
@@ -1,89 +0,0 @@
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
-  /* Read-only sections, merged into text segment: */
-  . = + SIZEOF_HEADERS;
-  .text      :
-  {
-    /* WARNING - the following is hand-optimized to fit within	*/
-    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
-    arch/powerpc/cpu/mpc8xx/start.o	(.text*)
-    arch/powerpc/cpu/mpc8xx/traps.o	(.text*)
-
-    *(.text*)
-  }
-  _etext = .;
-  PROVIDE (etext = .);
-  .rodata    :
-  {
-    *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-  }
-
-  /* Read-write section, merged into data segment: */
-  . = (. + 0x00FF) & 0xFFFFFF00;
-  _erotext = .;
-  PROVIDE (erotext = .);
-  .reloc   :
-  {
-    _GOT2_TABLE_ = .;
-    KEEP(*(.got2))
-    KEEP(*(.got))
-    PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
-    _FIXUP_TABLE_ = .;
-    KEEP(*(.fixup))
-  }
-  __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
-  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
-  .data    :
-  {
-    *(.data*)
-    *(.sdata*)
-  }
-  _edata  =  .;
-  PROVIDE (edata = .);
-
-  . = .;
-
-  . = ALIGN(4);
-  .u_boot_list : {
-	KEEP(*(SORT(.u_boot_list*)));
-  }
-
-
-  . = .;
-  __start___ex_table = .;
-  __ex_table : { *(__ex_table) }
-  __stop___ex_table = .;
-
-  . = ALIGN(256);
-  __init_begin = .;
-  .text.init : { *(.text.init) }
-  .data.init : { *(.data.init) }
-  . = ALIGN(256);
-  __init_end = .;
-
-  __bss_start = .;
-  .bss (NOLOAD)       :
-  {
-   *(.bss*)
-   *(.sbss*)
-   *(COMMON)
-   . = ALIGN(4);
-  }
-  __bss_end = . ;
-  PROVIDE (end = .);
-  . = ALIGN(128 * 1024);
-  .ppcenv	:
-  {
-    common/env_embedded.o (.ppcenv)
-  }
-}
diff --git a/configs/R360MPI_defconfig b/configs/R360MPI_defconfig
deleted file mode 100644
index 290f694..0000000
--- a/configs/R360MPI_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_R360MPI=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 00a5447..1e475af 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+R360MPI          powerpc     mpc8xx         -           -           Wolfgang Denk <wd@denx.de>
 RRvision         powerpc     mpc8xx         -           -           Wolfgang Denk <wd@denx.de>
 SPD823TS         powerpc     mpc8xx         -           -           Wolfgang Denk <wd@denx.de>
 KUP4K            powerpc     mpc8xx         -           -           Klaus Heydeck <heydeck@kieback-peter.de>
diff --git a/drivers/video/mpc8xx_lcd.c b/drivers/video/mpc8xx_lcd.c
index a5c1e19..336788f 100644
--- a/drivers/video/mpc8xx_lcd.c
+++ b/drivers/video/mpc8xx_lcd.c
@@ -423,31 +423,6 @@ void lcd_enable (void)
 	pic_write (0x60, c);
     }
 #endif /* CONFIG_LWMON */
-
-#if defined(CONFIG_R360MPI)
-    {
-	extern void r360_i2c_lcd_write (uchar data0, uchar data1);
-	unsigned long bgi, ctr;
-	char *p;
-
-	if ((p = getenv("lcdbgi")) != NULL) {
-		bgi = simple_strtoul (p, 0, 10) & 0xFFF;
-	} else {
-		bgi = 0xFFF;
-	}
-
-	if ((p = getenv("lcdctr")) != NULL) {
-		ctr = simple_strtoul (p, 0, 10) & 0xFFF;
-	} else {
-		ctr=0x7FF;
-	}
-
-	r360_i2c_lcd_write(0x10, 0x01);
-	r360_i2c_lcd_write(0x20, 0x01);
-	r360_i2c_lcd_write(0x30 | ((bgi>>8) & 0xF), bgi & 0xFF);
-	r360_i2c_lcd_write(0x40 | ((ctr>>8) & 0xF), ctr & 0xFF);
-    }
-#endif /* CONFIG_R360MPI */
 }
 
 /************************************************************************/
diff --git a/include/commproc.h b/include/commproc.h
index 7d62861..38e4e7d 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -630,7 +630,6 @@ typedef struct scc_enet {
 /***  MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI  **********/
 
 #if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
-    defined(CONFIG_R360MPI) || \
     defined(CONFIG_TQM823L) || \
     defined(CONFIG_TQM823M) || defined(CONFIG_TQM850L) || \
     defined(CONFIG_TQM850M) || defined(CONFIG_TQM885D)
@@ -650,9 +649,6 @@ typedef struct scc_enet {
 
 #define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
 #define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
-#if defined(CONFIG_R360MPI)
-#define PC_ENET_LBK	((ushort)0x0008)	/* PC 12 */
-#endif   /* CONFIG_R360MPI */
 
 /* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
  * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
diff --git a/include/configs/R360MPI.h b/include/configs/R360MPI.h
deleted file mode 100644
index 009d1cf..0000000
--- a/include/configs/R360MPI.h
+++ /dev/null
@@ -1,464 +0,0 @@
-/*
- * (C) Copyright 2000-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
-#define CONFIG_R360MPI		1
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-#define CONFIG_LCD
-#define CONFIG_MPC8XX_LCD
-#undef  CONFIG_EDT32F10
-#define CONFIG_SHARP_LQ057Q3DC02
-
-#define	CONFIG_SPLASH_SCREEN
-
-#define MPC8XX_FACT             1		/* Multiply by 1	*/
-#define MPC8XX_XIN              50000000	/* 50 MHz in		*/
-#define CONFIG_8xx_GCLK_FREQ    50000000 /* define if can't use get_gclk_freq */
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		115200	/* console baudrate in bps	*/
-#if 0
-#define CONFIG_BOOTDELAY	0	/* immediate boot		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"bootp; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#undef	CONFIG_SCC1_ENET
-#define	CONFIG_SCC2_ENET
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#define	CONFIG_MISC_INIT_R		/* have misc_init_r() function	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_CAN_DRIVER		/* CAN Driver support enabled	*/
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
-
-#define CONFIG_HARD_I2C		1	/* To I2C with hardware support */
-#undef CONFIG_SYS_I2C_SOFT		/* To I2C with software support */
-#define CONFIG_SYS_I2C_SPEED		4700	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-#if defined(CONFIG_SYS_I2C_SOFT)
-#define CONFIG_SYS_SYS_I2C_SOFT_SPEED	4700 /* I2C speed and slave address */
-#define CONFIG_SYS_SYS_I2C_SOFT_SLAVE	0x7F
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL			0x00000020	/* PB 26 */
-#define PB_SDA			0x00000010	/* PB 27 */
-
-#define I2C_INIT		(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE		(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE		(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ		((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-				else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-				else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY		udelay(50)
-#endif /* #define(CONFIG_SYS_I2C_SOFT) */
-
-#define CONFIG_SYS_I2C_LCD_ADDR	0x8	/* LCD Control */
-#define CONFIG_SYS_I2C_KEY_ADDR	0x9	/* Keyboard coprocessor */
-#define CONFIG_SYS_I2C_TEM_ADDR	0x49	/* Temperature Sensors */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCMCIA
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_DEVICE_NULLDEV	1	/* we need the null device	*/
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1	/* must set console from env	*/
-
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/
-
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition
- * use all the space starting at offset 3MB*/
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00300000
-
-/* mtdparts command line support */
-/*
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT		"nor0=r360-0"
-#define MTDPARTS_DEFAULT	"mtdparts=r360-0:- at 3m(user)"
-*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x40000000
-#if defined(DEBUG)
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x40000	/* Offset of Environment		*/
-#define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment sector	*/
-#define	CONFIG_ENV_SIZE		0x4000	/* Used Size of Environment sector	*/
-#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
- */
-#ifdef	CONFIG_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
-#define CONFIG_SYS_PLPRCR							\
-		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
-#else			/* up to 50 MHz we use a 1:1 clock */
-#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
-#endif	/* CONFIG_80MHz */
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-#define CONFIG_SYS_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#if 1
-#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
-#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
-#endif
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFF000000	/* OR addr mask */
-
-/*
- * FLASH timing:
- */
-#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1 | OR_SCY_7_CLK | OR_BI)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-
-/*
- * BR2 and OR2 (SDRAM)
- *
- */
-#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
-#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/
-
-#define CONFIG_SYS_PRELIM_OR2_AM	0xF8000000	/* OR addr mask */
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CONFIG_SYS_OR_TIMING_SDRAM	(OR_ACS_DIV1  | OR_CSNT_SAM | \
-				 OR_SCY_0_CLK | OR_G5LS)
-
-#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR2_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/*
- * BR3 and OR3 (CAN Controller)
- */
-#ifdef CONFIG_CAN_DRIVER
-#define CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN base address   */
-#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask */
-#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA |OR_BI)
-#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
-				 BR_PS_8 | BR_MS_UPMB | BR_V)
-#endif	/* CONFIG_CAN_DRIVER */
-
-
-/*
- * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
- */
-#if   defined(CONFIG_80MHz)
-#define CONFIG_SYS_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CONFIG_SYS_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CONFIG_SYS_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
-
-/*
- * For 16 MBit, refresh rates could be 31.3 us
- * (= 64 ms / 2K = 125 / quad bursts).
- * For a simpler initialization, 15.6 us is used instead.
- *
- * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
- * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
- */
-#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
-#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
-#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-
-#endif	/* __CONFIG_H */
diff --git a/include/pcmcia.h b/include/pcmcia.h
index 371c9a4..7e495bc 100644
--- a/include/pcmcia.h
+++ b/include/pcmcia.h
@@ -27,8 +27,6 @@
 # define CONFIG_PCMCIA_SLOT_A
 #elif defined(CONFIG_LWMON)		/* The LWMON  use SLOT_B	*/
 # define CONFIG_PCMCIA_SLOT_B
-#elif defined(CONFIG_R360MPI)		/* The R360MPI use SLOT_B	*/
-# define CONFIG_PCMCIA_SLOT_B
 #elif defined(CONFIG_ATC)		/* The ATC use SLOT_A	*/
 # define CONFIG_PCMCIA_SLOT_A
 #else
-- 
1.9.1