From: Eyal Reizer <eyalreizer@gmail.com>
To: bcousson@baylibre.com, tony@atomide.com, robh+dt@kernel.org,
mark.rutland@arm.com, linux-omap@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Eyal Reizer <eyalr@ti.com>
Subject: [PATCH] arm: dts: am437x-sk-evm: add wilink8 support
Date: Tue, 1 May 2018 10:24:13 +0300 [thread overview]
Message-ID: <1525159453-32489-1-git-send-email-eyalr@ti.com> (raw)
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
---
arch/arm/boot/dts/am437x-sk-evm.dts | 115 ++++++++++++++++++++++++++++++++++++
1 file changed, 115 insertions(+)
diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts
index 16d9db0..afffdb1 100644
--- a/arch/arm/boot/dts/am437x-sk-evm.dts
+++ b/arch/arm/boot/dts/am437x-sk-evm.dts
@@ -15,6 +15,7 @@
#include <dt-bindings/pwm/pwm.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "TI AM437x SK EVM";
@@ -158,6 +159,22 @@
};
};
};
+
+ vmmcwl_fixed: fixedregulator-mmcwl {
+ /*
+ * WL_EN is not SDIO standard compliant. It is an out of band
+ * signal and hard to be dealt with in a standard way by the
+ * SDIO core driver.
+ * So modelling the WL_EN line as a regulator was a natural
+ * choice as the MMC core already deals with MMC supplies.
+ */
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcwl_fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
&am43xx_pinmux {
@@ -424,6 +441,62 @@
AM4372_IOPAD(0xac4, PIN_OUTPUT | MUX_MODE0) /* usb0_drvvbus.usb0_drvvbus */
>;
};
+
+ mmc3_pins_default: pinmux_mmc3_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9f0, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD21) cam1_data2.mmc2_clk */
+ AM4372_IOPAD(0x9f4, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE22) cam1_data3.mmc2_cmd */
+ AM4372_IOPAD(0x9f8, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD22) cam1_data4.mmc2_dat0 */
+ AM4372_IOPAD(0x9fc, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE23) cam1_data5.mmc2_dat1 */
+ AM4372_IOPAD(0xa00, PIN_INPUT_PULLUP | MUX_MODE3) /* (AD23) cam1_data6.mmc2_dat2 */
+ AM4372_IOPAD(0xa04, PIN_INPUT_PULLUP | MUX_MODE3) /* (AE24) cam1_data7.mmc2_dat3 */
+ >;
+ };
+
+ mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9f0, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD21) cam1_data2.mmc2_clk */
+ AM4372_IOPAD(0x9f4, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE22) cam1_data3.mmc2_cmd */
+ AM4372_IOPAD(0x9f8, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD22) cam1_data4.mmc2_dat0 */
+ AM4372_IOPAD(0x9fc, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE23) cam1_data5.mmc2_dat1 */
+ AM4372_IOPAD(0xa00, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AD23) cam1_data6.mmc2_dat2 */
+ AM4372_IOPAD(0xa04, PIN_INPUT_PULLDOWN | MUX_MODE7) /* (AE24) cam1_data7.mmc2_dat3 */
+ >;
+ };
+
+ wlan_pins_default: pinmux_wlan_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
+ AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
+ >;
+ };
+
+ wlan_pins_sleep: pinmux_wlan_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9d0, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data8.gpio4_8 WL_EN */
+ AM4372_IOPAD(0x9e4, PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7) /* cam1_wen.gpio4_13 WL_IRQ */
+ >;
+ };
+
+ uart1_bt_pins_default: pinmux_uart1_bt_pins_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x980, PIN_INPUT | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ AM4372_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
+ >;
+ };
+
+ uart1_bt_pins_sleep: pinmux_uart1_bt_pins_sleep {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x980, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rxd.uart1_rxd */
+ AM4372_IOPAD(0x984, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_txd.uart1_txd */
+ AM4372_IOPAD(0x978, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_ctsn.uart1_ctsn */
+ AM4372_IOPAD(0x97c, PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* uart1_rtsn.uart1_rtsn */
+ AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE7) /* cam1_data9.gpio4_7 BT_EN */
+ >;
+ };
};
&i2c0 {
@@ -606,6 +679,10 @@
status = "okay";
};
+&gpio4 {
+ status = "okay";
+};
+
&gpio5 {
status = "okay";
};
@@ -620,6 +697,44 @@
cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&uart1_bt_pins_default>;
+ pinctrl-1 = <&uart1_bt_pins_sleep>;
+};
+
+&mmc3 {
+ status = "okay";
+ /*
+ * these are on the crossbar and are outlined in the
+ * xbar-event-map element
+ */
+ dmas = <&edma_xbar 30 0 1>,
+ <&edma_xbar 31 0 2>;
+ dma-names = "tx", "rx";
+ vmmc-supply = <&vmmcwl_fixed>;
+ bus-width = <4>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&mmc3_pins_default>;
+ pinctrl-1 = <&mmc3_pins_sleep>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ ti,non-removable;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@0 {
+ compatible = "ti,wl1835";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&wlan_pins_default>;
+ pinctrl-1 = <&wlan_pins_sleep>;
+ reg = <2>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
&usb2_phy1 {
status = "okay";
};
--
2.7.4
next reply other threads:[~2018-05-01 7:24 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-01 7:24 Eyal Reizer [this message]
2018-05-02 8:30 ` [PATCH] arm: dts: am437x-sk-evm: add wilink8 support Sekhar Nori
2018-05-02 8:30 ` Sekhar Nori
2018-05-02 13:40 ` Reizer, Eyal
2018-05-02 14:51 ` Tony Lindgren
2018-05-03 6:41 ` [EXTERNAL] " Reizer, Eyal
2018-05-03 14:17 ` Tony Lindgren
2018-05-06 7:45 ` Reizer, Eyal
2018-05-06 16:56 ` Tony Lindgren
2018-05-07 6:55 ` Reizer, Eyal
2018-05-07 15:08 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1525159453-32489-1-git-send-email-eyalr@ti.com \
--to=eyalreizer@gmail.com \
--cc=bcousson@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=eyalr@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.