(unknown)

[yue-feng sun <sunyf@ldeo.columbia.edu>]

[-- Attachment #1: Type: TEXT/plain, Size: 2214 bytes --]

Dear All,
    
     I went over the archives and could not locate any solution.
Hope experts on this mailing -list can help me on solving
my second hard drive problem:


     The second hard drive in the modular bay of my DELL Precision
     Mobil workstation M60 is not usable. It is recognized during the boot
     as  hdc: FUJITSU MHT2040AH, ATA DISK drive

     I am running RH9 with Linux Kernel 2.4.20-13.9


The dmesg shows:
-------------------------------------------------------------
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi

hda: HTS726060M9AT00, ATA DISK drive
blk: queue c03cbfa0, I/O limit 4095Mb (mask 0xffffffff)
hdc: FUJITSU MHT2040AH, ATA DISK drive
blk: queue c03cc404, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117210240 sectors (60012 MB) w/7877KiB Cache, CHS=7296/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
 hdc:end_request: I/O error, dev 16:00 (hdc), sector 0
end_request: I/O error, dev 16:00 (hdc), sector 2
end_request: I/O error, dev 16:00 (hdc), sector 4
end_request: I/O error, dev 16:00 (hdc), sector 6
end_request: I/O error, dev 16:00 (hdc), sector 0
end_request: I/O error, dev 16:00 (hdc), sector 2
end_request: I/O error, dev 16:00 (hdc), sector 4
end_request: I/O error, dev 16:00 (hdc), sector 6
 unable to read partition table
ide-floppy driver 0.99.newide
-------------------------------------------------------------


I remember that during the boot, there was a message like
 hardwaremodprobe can not locate module ide-disk ...



After booting, I got the following errors:

#fdisk /dev/hdc

hdc: driver not present
unable to open /dev/hdc


After shutting down, there was a message like:

flusing devices hda, hdc

The detailed dmesg log is attached.


The drive was originally partitioned as Dynamic. I used Partition Magic to
convert it to Basic partition and it was formatted to two FAT32 partitions
under Windows 2000. Now I would like to use it as a linux file system
if I could use fdisk to repartition and format it.


Thanks,

Sun

[-- Attachment #2: dmesg.log --]
[-- Type: TEXT/plain, Size: 11745 bytes --]

Linux version 2.4.20-13.9 (bhcompile@porky.devel.redhat.com) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon May 12 10:55:37 EDT 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003ffae000 (usable)
 BIOS-e820: 000000003ffae000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262062
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32686 pages.
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1694.516 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3381.65 BogoMIPS
Memory: 1027148k/1048248k available (1355k kernel code, 17516k reserved, 1004k data, 132k init, 130744k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: a7e9f9bf 00000000 00000000 00000000
CPU:             Common caps: a7e9f9bf 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) M processor 1700MHz stepping 05
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfc97e, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX [8086/24cc] at 00:1f.0
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 00:1d.2
PCI: Sharing IRQ 11 with 02:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 11 for device 00:1f.6
PCI: Sharing IRQ 11 with 00:1f.5
PCI: Sharing IRQ 11 with 02:03.0
Real Time Clock Driver v1.10e
floppy0: no floppy controllers found
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta3-.2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 00:1d.2
PCI: Sharing IRQ 11 with 02:00.0
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
hda: HTS726060M9AT00, ATA DISK drive
blk: queue c03cbfa0, I/O limit 4095Mb (mask 0xffffffff)
hdc: FUJITSU MHT2040AH, ATA DISK drive
blk: queue c03cc404, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 117210240 sectors (60012 MB) w/7877KiB Cache, CHS=7296/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
 hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 >
 hdc:end_request: I/O error, dev 16:00 (hdc), sector 0
end_request: I/O error, dev 16:00 (hdc), sector 2
end_request: I/O error, dev 16:00 (hdc), sector 4
end_request: I/O error, dev 16:00 (hdc), sector 6
end_request: I/O error, dev 16:00 (hdc), sector 0
end_request: I/O error, dev 16:00 (hdc), sector 2
end_request: I/O error, dev 16:00 (hdc), sector 4
end_request: I/O error, dev 16:00 (hdc), sector 6
 unable to read partition table
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 143k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 11 for device 00:1d.7
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB EHCI Controller
ehci-hcd 00:1d.7: irq 11, pci mem f8849c00
usb.c: new USB bus registered, assigned bus number 1
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 6 ports detected
usb-uhci.c: $Revision: 1.275 $ time 11:00:49 May 12 2003
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:1d.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xbf80, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:1d.1
PCI: Sharing IRQ 11 with 02:01.0
PCI: Sharing IRQ 11 with 02:01.1
PCI: Sharing IRQ 11 with 02:01.2
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xbf40, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:1d.2
PCI: Sharing IRQ 11 with 00:1f.1
PCI: Sharing IRQ 11 with 02:00.0
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xbf20, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:1d.7-6, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Adding Swap: 2152668k swap-space (priority -1)
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
hub.c: new USB device 00:1d.7-6.1, assigned address 3
hub.c: USB hub found
hub.c: 3 ports detected
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hub.c: new USB device 00:1d.7-6.2, assigned address 4
input0: USB HID v1.10 Mouse [GenesysLogic USB Mouse] on usb1:4.0
hub.c: new USB device 00:1d.7-6.1.1, assigned address 5
ohci1394: $Rev: 693 $ Ben Collins <bcollins@debian.org>
PCI: Found IRQ 11 for device 02:01.2
PCI: Sharing IRQ 11 with 00:1d.1
PCI: Sharing IRQ 11 with 02:01.0
PCI: Sharing IRQ 11 with 02:01.1
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[11]  MMIO=[fafef800-fafeffff]  Max Packet=[2048]
ieee1394: SelfID completion called outside of bus reset!
ieee1394: Host added: Node[00:1023]  GUID[314fc000226d0881]  [Linux OHCI-1394]
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
input1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard Hub] on usb1:5.0
input2: USB HID v1.10 Pointer [Dell Dell USB Keyboard Hub] on usb1:5.1
ide-floppy driver 0.99.newide
usbdevfs: USBDEVFS_CONTROL failed dev 4 rqt 128 rq 6 len 9 ret -71
usbdevfs: USBDEVFS_CONTROL failed dev 4 rqt 128 rq 6 len 34 ret -71
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
ip_tables: (C) 2000-2002 Netfilter core team
Broadcom Gigabit Ethernet Driver bcm5700 with Broadcom NIC Extension (NICE) ver. 5.0.16 (01/03/03)
divert: allocating divert_blk for eth0
PCI: Found IRQ 11 for device 02:00.0
PCI: Sharing IRQ 11 with 00:1d.2
PCI: Sharing IRQ 11 with 00:1f.1
eth0: Broadcom BCM5705M 1000Base-T found at mem faff0000, IRQ 11, node addr 000d56acc83f
eth0: Broadcom BCM5705 Integrated Copper transceiver found
eth0: Scatter-gather ON, 64-bit DMA ON, Tx Checksum ON, Rx Checksum ON, 802.1Q VLAN ON
ip_tables: (C) 2000-2002 Netfilter core team
bcm5700: eth0 NIC Link is DOWN
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 02:01.0
PCI: Sharing IRQ 11 with 00:1d.1
PCI: Sharing IRQ 11 with 02:01.1
PCI: Sharing IRQ 11 with 02:01.2
PCI: Found IRQ 11 for device 02:01.1
PCI: Sharing IRQ 11 with 00:1d.1
PCI: Sharing IRQ 11 with 02:01.0
PCI: Sharing IRQ 11 with 02:01.2
Yenta IRQ list 06f8, PCI irq11
Socket status: 30000006
Yenta IRQ list 06f8, PCI irq11
Socket status: 30000047
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module  1.0-5328  Wed Dec 17 13:54:51 PST 2003
Intel 810 + AC97 Audio, version 0.24, 11:00:30 May 12 2003
PCI: Found IRQ 11 for device 00:1f.5
PCI: Sharing IRQ 11 with 00:1f.6
PCI: Sharing IRQ 11 with 02:03.0
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xbc40 and 0xb800, MEM 0xf4fff800 and 0xf4fff400, IRQ 11
i810: Intel ICH4 mmio at 0xf9d31800 and 0xf9d33400
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7650 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
hub.c: new USB device 00:1d.1-2, assigned address 2
usb.c: USB device 2 (vend/prod 0xd7d/0x100) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
  Vendor:           Model: USB DISK          Rev: 1.06
  Type:   Direct-Access                      ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
ide-floppy driver 0.99.newide