Re: [PATCH] bcm43xx: Fix loss of association after resume

["Rafael J. Wysocki" <rjw@sisk.pl>]

On Sunday, 11 February 2007 14:07, Michael Buesch wrote:
> On Sunday 11 February 2007 13:56, Rafael J. Wysocki wrote:
> > On Saturday, 10 February 2007 21:33, Larry Finger wrote:
> > > Rafael,
> > > 
> > > Rafael J. Wysocki wrote:
> > > > 
> > > > I'm running with this patch applied right now, but the association is lost
> > > > after the resume anyway.  I have to reload bcm43xx to make it associate with
> > > > the AP again (no big deal).
> > > 
> > > 
> > > Please send me the output of iwconfig and ifconfig after the resume, but before you reload bcm43xx.
> > 
> > albercik:~ # iwconfig
> > lo        no wireless extensions.
> > 
> > eth0      no wireless extensions.
> > 
> > eth1      IEEE 802.11b/g  ESSID:"DI524"  Nickname:"Broadcom 4311"
> >           Mode:Managed  Frequency=2.484 GHz  Access Point: Invalid
> >           Bit Rate=1 Mb/s   Tx-Power=18 dBm
> >           RTS thr:off   Fragment thr:off
> >           Encryption key:off
> >           Link Quality=0/100  Signal level=-256 dBm  Noise level=-256 dBm
> >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> >           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> > 
> > albercik:~ # ifconfig eth1
> > eth1      Link encap:Ethernet  HWaddr 00:14:A5:BE:95:31
> >           inet addr:192.168.100.101  Bcast:192.168.100.255  Mask:255.255.255.0
> >           inet6 addr: fe80::214:a5ff:febe:9531/64 Scope:Link
> >           UP BROADCAST MULTICAST  MTU:1500  Metric:1
> >           RX packets:5137 errors:0 dropped:120 overruns:0 frame:0
> >           TX packets:5703 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:1000
> >           RX bytes:4569090 (4.3 Mb)  TX bytes:156826797 (149.5 Mb)
> >           Interrupt:18
> > 
> > albercik:~ # ifconfig eth1 down
> > albercik:~ # ifconfig eth1 up
> > SIOCSIFFLAGS: No such device
> 		^^^^^
> 
> I'd like to see dmesg, please.

Appended.  It covers one suspend-resume cycle (suspend to disk).  I have
filtered HID-related messages out of it.

Greetings,
Rafael


ton.000e = 0
usb 3-1: usb auto-resume
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00040103 PSSC PPS PES CCS
usb 3-1: finish resume
usb usb1: usb auto-resume
usb usb1: finish resume
hub 1-0:1.0: hub_resume
ehci_hcd 0000:00:13.2: resume root hub
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
usb 3-1: usb auto-suspend
hub 1-0:1.0: hub_suspend
usb usb1: usb auto-suspend
PM: Adding info for No Bus:vcs8
PM: Adding info for No Bus:vcsa8
SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
Stopping tasks ... done.
Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\bdone (113015 pages freed)
Freed 452060 kbytes in 1.44 seconds (313.93 MB/s)
Suspending console(s)
usbhid 3-4:1.0: freeze
usb 3-4: freeze
usbhid 3-4:1.0: suspend
usb 3-4: usb suspend
 usbdev3.18: PM: suspend 0->1, parent 3-1 already 2
 usbdev3.18_ep02: PM: suspend 0->1, parent 3-1:1.0 already 2
 usbdev3.18_ep81: PM: suspend 0->1, parent 3-1:1.0 already 2
usb 3-1:1.0: PM: suspend 2-->1
usb 3-1:1.0: PM: suspend 2->1, parent 3-1 already 2
 usbdev3.18_ep00: PM: suspend 0->1, parent 3-1 already 2
usb 3-1: PM: suspend 2-->1
usb 2-2:1.3: freeze
usb 2-2:1.2: freeze
hci_usb 2-2:1.1: freeze
hci_usb 2-2:1.0: freeze
usb 2-2: freeze
usb 2-2: usb suspend
serio serio6: freeze
platform bluetooth: freeze
hub 3-0:1.0: freeze
usb usb3: freeze
hub 3-0:1.0: hub_suspend
ohci_hcd 0000:00:13.1: suspend root hub
usb usb3: usb suspend
hub 2-0:1.0: freeze
usb usb2: freeze
hub 2-0:1.0: hub_suspend
ohci_hcd 0000:00:13.0: suspend root hub
usb usb2: usb suspend
 usbdev1.1: PM: suspend 0->1, parent usb1 already 2
 usbdev1.1_ep81: PM: suspend 0->1, parent 1-0:1.0 already 2
hub 1-0:1.0: PM: suspend 2-->1
hub 1-0:1.0: PM: suspend 2->1, parent usb1 already 2
 usbdev1.1_ep00: PM: suspend 0->1, parent usb1 already 2
usb usb1: PM: suspend 2-->1
ide-cdrom 0.0: freeze
psmouse serio4: freeze
serio serio3: freeze
serio serio2: freeze
serio serio1: freeze
atkbd serio0: freeze
i8042 i8042: freeze
sd 0:0:0:0: freeze
serial8250 serial8250: freeze
vesafb vesafb.0: freeze
pci_express 0000:00:06.0:pcie03: freeze
pci_express 0000:00:06.0:pcie01: freeze
pci_express 0000:00:06.0:pcie00: freeze
pci_express 0000:00:05.0:pcie03: freeze
pci_express 0000:00:05.0:pcie01: freeze
pci_express 0000:00:05.0:pcie00: freeze
pci_express 0000:00:04.0:pcie03: freeze
pci_express 0000:00:04.0:pcie01: freeze
pci_express 0000:00:04.0:pcie00: freeze
pcspkr pcspkr: freeze
sdhci 0000:02:04.3: freeze
ACPI: PCI interrupt for device 0000:02:04.3 disabled
tifm_7xx1 0000:02:04.2: freeze
ACPI: PCI interrupt for device 0000:02:04.2 disabled
ohci1394 0000:02:04.1: freeze
ohci1394 does not fully support suspend and resume yet
ieee1394: hpsb_bus_reset called while bus reset already in progress
yenta_cardbus 0000:02:04.0: freeze
tg3 0000:02:01.0: freeze
PM: Writing back config space on device 0000:02:01.0 at offset b (was 3ed173b, writing 30b0103c)
PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:02:01.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:02:01.0 at offset 0 (was 3ed173b, writing 169c14e4)
bcm43xx 0000:30:00.0: freeze
bcm43xx: Suspending...
PM: Removing info for No Bus:hw_random
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 3/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
ACPI: PCI interrupt for device 0000:30:00.0 disabled
bcm43xx: Device suspended.
pci 0000:01:05.0: freeze
k8temp 0000:00:18.3: freeze
pci 0000:00:18.2: freeze
pci 0000:00:18.1: freeze
pci 0000:00:18.0: freeze
pci 0000:00:14.4: freeze
pci 0000:00:14.3: freeze
HDA Intel 0000:00:14.2: freeze
ACPI: PCI interrupt for device 0000:00:14.2 disabled
ATIIXP_IDE 0000:00:14.1: freeze
piix4_smbus 0000:00:14.0: freeze
ehci_hcd 0000:00:13.2: freeze
ACPI: PCI interrupt for device 0000:00:13.2 disabled
ehci_hcd 0000:00:13.2: --> PCI D3
ohci_hcd 0000:00:13.1: freeze
ACPI: PCI interrupt for device 0000:00:13.1 disabled
ohci_hcd 0000:00:13.1: --> PCI D0/legacy
ohci_hcd 0000:00:13.0: freeze
ACPI: PCI interrupt for device 0000:00:13.0 disabled
ohci_hcd 0000:00:13.0: --> PCI D0/legacy
sata_sil 0000:00:12.0: freeze
pcieport-driver 0000:00:06.0: freeze
pcieport-driver 0000:00:05.0: freeze
pcieport-driver 0000:00:04.0: freeze
pci 0000:00:01.0: freeze
pci 0000:00:00.0: freeze
ACPI Thermal Zone Driver thermal:03: freeze
ACPI Thermal Zone Driver thermal:02: freeze
ACPI Thermal Zone Driver thermal:01: freeze
ACPI Fan Driver PNP0C0B:03: freeze
ACPI Fan Driver PNP0C0B:02: freeze
ACPI: Transitioning device [C351] to D0
ACPI: Transitioning device [C351] to D0
ACPI Fan Driver PNP0C0B:01: freeze
ACPI: Transitioning device [C350] to D0
ACPI: Transitioning device [C350] to D0
ACPI Fan Driver PNP0C0B:00: freeze
ACPI: Transitioning device [C34F] to D0
ACPI: Transitioning device [C34F] to D0
ACPI Power Resource Driver power_resource:06: freeze
ACPI Power Resource Driver power_resource:05: freeze
ACPI Power Resource Driver power_resource:04: freeze
ACPI Power Resource Driver power_resource:03: freeze
acpi thermal:00: freeze
acpi PNP0C02:02: freeze
acpi PNP0C14:00: freeze
ACPI Button Driver PNP0C0D:00: freeze
ACPI Button Driver PNP0C0E:00: freeze
ACPI AC Adapter Driver ACPI0003:00: freeze
ACPI Battery Driver PNP0C0A:01: freeze
ACPI Battery Driver PNP0C0A:00: freeze
acpi HPQ0006:00: freeze
acpi PNP0C02:01: freeze
acpi device:49: freeze
acpi device:48: freeze
acpi device:47: freeze
acpi device:46: freeze
acpi device:45: freeze
acpi device:44: freeze
acpi device:43: freeze
acpi device:42: freeze
acpi device:41: freeze
acpi device:40: freeze
acpi device:3f: freeze
acpi device:3e: freeze
acpi device:3d: freeze
acpi device:3c: freeze
acpi device:3b: freeze
acpi device:3a: freeze
acpi device:39: freeze
acpi device:38: freeze
acpi device:37: freeze
acpi device:36: freeze
acpi device:35: freeze
acpi device:34: freeze
acpi device:33: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:07: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:06: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:05: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:04: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:03: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:02: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:01: freeze
ACPI PCI Interrupt Link Driver PNP0C0F:00: freeze
acpi device:32: freeze
acpi device:31: freeze
acpi device:30: freeze
acpi device:2f: freeze
acpi device:2e: freeze
acpi device:2d: freeze
acpi device:2c: freeze
acpi device:2b: freeze
acpi device:2a: freeze
acpi device:29: freeze
acpi device:28: freeze
acpi device:27: freeze
acpi device:26: freeze
acpi device:25: freeze
acpi device:24: freeze
acpi device:23: freeze
acpi device:22: freeze
acpi device:21: freeze
acpi device:20: freeze
acpi device:1f: freeze
acpi device:1e: freeze
acpi device:1d: freeze
acpi device:1c: freeze
acpi device:1b: freeze
acpi device:1a: freeze
acpi device:19: freeze
acpi device:18: freeze
acpi device:17: freeze
acpi device:16: freeze
acpi device:15: freeze
acpi device:14: freeze
acpi device:13: freeze
acpi device:12: freeze
acpi device:11: freeze
acpi device:10: freeze
acpi PNP0C02:00: freeze
acpi PNP0000:00: freeze
ACPI Power Resource Driver power_resource:02: freeze
acpi SYN0118:00: freeze
acpi PNP0303:00: freeze
acpi PNP0B00:00: freeze
acpi PNP0800:00: freeze
acpi PNP0200:00: freeze
acpi PNP0100:00: freeze
acpi PNP0C04:00: freeze
acpi IFX0102:00: freeze
ACPI Power Resource Driver power_resource:01: freeze
acpi PNP0401:00: freeze
ACPI container driver PNP0A06:00: freeze
ACPI Embedded Controller Driver PNP0C09:00: freeze
acpi device:0f: freeze
acpi device:0e: freeze
ACPI Power Resource Driver power_resource:00: freeze
acpi device:0d: freeze
acpi device:0c: freeze
acpi device:0b: freeze
acpi device:0a: freeze
acpi device:09: freeze
acpi device:08: freeze
acpi device:07: freeze
acpi device:06: freeze
acpi device:05: freeze
acpi device:04: freeze
acpi device:03: freeze
acpi device:02: freeze
acpi video:00: freeze
acpi device:01: freeze
ACPI PCI Root Bridge Driver PNP0A03:00: freeze
acpi PNP0C01:00: freeze
acpi device:00: freeze
ACPI Processor Driver ACPI0007:01: freeze
ACPI Processor Driver ACPI0007:00: freeze
ACPI Button Driver button_power:00: freeze
acpi acpi_system:00: freeze
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU1 is down
platform bluetooth: LATE freeze
i8042 i8042: LATE freeze
serial8250 serial8250: LATE freeze
vesafb vesafb.0: LATE freeze
pcspkr pcspkr: LATE freeze
sdhci 0000:02:04.3: LATE freeze
tifm_7xx1 0000:02:04.2: LATE freeze
ohci1394 0000:02:04.1: LATE freeze
yenta_cardbus 0000:02:04.0: LATE freeze
tg3 0000:02:01.0: LATE freeze
bcm43xx 0000:30:00.0: LATE freeze
pci 0000:01:05.0: LATE freeze
k8temp 0000:00:18.3: LATE freeze
pci 0000:00:18.2: LATE freeze
pci 0000:00:18.1: LATE freeze
pci 0000:00:18.0: LATE freeze
pci 0000:00:14.4: LATE freeze
pci 0000:00:14.3: LATE freeze
HDA Intel 0000:00:14.2: LATE freeze
ATIIXP_IDE 0000:00:14.1: LATE freeze
piix4_smbus 0000:00:14.0: LATE freeze
pcieport-driver 0000:00:06.0: LATE freeze
pcieport-driver 0000:00:05.0: LATE freeze
pcieport-driver 0000:00:04.0: LATE freeze
pci 0000:00:01.0: LATE freeze
pci 0000:00:00.0: LATE freeze
Extended CMOS year: 2000
swsusp: critical section: 
swsusp: Need to copy 95157 pages
swsusp: Normal pages needed: 95157 + 1024 + 20, available pages: 134073
Extended CMOS year: 2000
pci 0000:00:00.0: EARLY resume
pci 0000:00:01.0: EARLY resume
pcieport-driver 0000:00:04.0: EARLY resume
pcieport-driver 0000:00:05.0: EARLY resume
pcieport-driver 0000:00:06.0: EARLY resume
sata_sil 0000:00:12.0: EARLY resume
ohci_hcd 0000:00:13.0: EARLY resume
ohci_hcd 0000:00:13.1: EARLY resume
ehci_hcd 0000:00:13.2: EARLY resume
piix4_smbus 0000:00:14.0: EARLY resume
ATIIXP_IDE 0000:00:14.1: EARLY resume
HDA Intel 0000:00:14.2: EARLY resume
pci 0000:00:14.3: EARLY resume
pci 0000:00:14.4: EARLY resume
pci 0000:00:18.0: EARLY resume
pci 0000:00:18.1: EARLY resume
pci 0000:00:18.2: EARLY resume
k8temp 0000:00:18.3: EARLY resume
pci 0000:01:05.0: EARLY resume
bcm43xx 0000:30:00.0: EARLY resume
tg3 0000:02:01.0: EARLY resume
yenta_cardbus 0000:02:04.0: EARLY resume
ohci1394 0000:02:04.1: EARLY resume
tifm_7xx1 0000:02:04.2: EARLY resume
sdhci 0000:02:04.3: EARLY resume
pcspkr pcspkr: EARLY resume
vesafb vesafb.0: EARLY resume
serial8250 serial8250: EARLY resume
i8042 i8042: EARLY resume
platform bluetooth: EARLY resume
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3990.23 BogoMIPS (lpj=7980462)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 510 cycles)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
CPU1 is up
acpi acpi_system:00: resuming
ACPI Button Driver button_power:00: resuming
ACPI Processor Driver ACPI0007:00: resuming
ACPI Processor Driver ACPI0007:01: resuming
acpi device:00: resuming
acpi PNP0C01:00: resuming
ACPI PCI Root Bridge Driver PNP0A03:00: resuming
acpi device:01: resuming
acpi video:00: resuming
acpi device:02: resuming
acpi device:03: resuming
acpi device:04: resuming
acpi device:05: resuming
acpi device:06: resuming
acpi device:07: resuming
acpi device:08: resuming
acpi device:09: resuming
acpi device:0a: resuming
acpi device:0b: resuming
acpi device:0c: resuming
acpi device:0d: resuming
ACPI Power Resource Driver power_resource:00: resuming
acpi device:0e: resuming
acpi device:0f: resuming
ACPI Embedded Controller Driver PNP0C09:00: resuming
ACPI container driver PNP0A06:00: resuming
acpi PNP0401:00: resuming
ACPI Power Resource Driver power_resource:01: resuming
acpi IFX0102:00: resuming
acpi PNP0C04:00: resuming
acpi PNP0100:00: resuming
acpi PNP0200:00: resuming
acpi PNP0800:00: resuming
acpi PNP0B00:00: resuming
acpi PNP0303:00: resuming
acpi SYN0118:00: resuming
ACPI Power Resource Driver power_resource:02: resuming
acpi PNP0000:00: resuming
acpi PNP0C02:00: resuming
acpi device:10: resuming
acpi device:11: resuming
acpi device:12: resuming
acpi device:13: resuming
acpi device:14: resuming
acpi device:15: resuming
acpi device:16: resuming
acpi device:17: resuming
acpi device:18: resuming
acpi device:19: resuming
acpi device:1a: resuming
acpi device:1b: resuming
acpi device:1c: resuming
acpi device:1d: resuming
acpi device:1e: resuming
acpi device:1f: resuming
acpi device:20: resuming
acpi device:21: resuming
acpi device:22: resuming
acpi device:23: resuming
acpi device:24: resuming
acpi device:25: resuming
acpi device:26: resuming
acpi device:27: resuming
acpi device:28: resuming
acpi device:29: resuming
acpi device:2a: resuming
acpi device:2b: resuming
acpi device:2c: resuming
acpi device:2d: resuming
acpi device:2e: resuming
acpi device:2f: resuming
acpi device:30: resuming
acpi device:31: resuming
acpi device:32: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:00: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:01: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:02: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:03: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:04: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:05: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:06: resuming
ACPI PCI Interrupt Link Driver PNP0C0F:07: resuming
acpi device:33: resuming
acpi device:34: resuming
acpi device:35: resuming
acpi device:36: resuming
acpi device:37: resuming
acpi device:38: resuming
acpi device:39: resuming
acpi device:3a: resuming
acpi device:3b: resuming
acpi device:3c: resuming
acpi device:3d: resuming
acpi device:3e: resuming
acpi device:3f: resuming
acpi device:40: resuming
acpi device:41: resuming
acpi device:42: resuming
acpi device:43: resuming
acpi device:44: resuming
acpi device:45: resuming
acpi device:46: resuming
acpi device:47: resuming
acpi device:48: resuming
acpi device:49: resuming
acpi PNP0C02:01: resuming
acpi HPQ0006:00: resuming
ACPI Battery Driver PNP0C0A:00: resuming
ACPI Battery Driver PNP0C0A:01: resuming
ACPI AC Adapter Driver ACPI0003:00: resuming
ACPI Button Driver PNP0C0E:00: resuming
ACPI Button Driver PNP0C0D:00: resuming
acpi PNP0C14:00: resuming
acpi PNP0C02:02: resuming
acpi thermal:00: resuming
ACPI Power Resource Driver power_resource:03: resuming
ACPI Power Resource Driver power_resource:04: resuming
ACPI Power Resource Driver power_resource:05: resuming
ACPI Power Resource Driver power_resource:06: resuming
ACPI Fan Driver PNP0C0B:00: resuming
ACPI: Transitioning device [C34F] to D0
ACPI: Transitioning device [C34F] to D0
ACPI Fan Driver PNP0C0B:01: resuming
ACPI: Transitioning device [C350] to D0
ACPI: Transitioning device [C350] to D0
ACPI Fan Driver PNP0C0B:02: resuming
ACPI: Transitioning device [C351] to D0
ACPI: Transitioning device [C351] to D0
ACPI Fan Driver PNP0C0B:03: resuming
ACPI Thermal Zone Driver thermal:01: resuming
ACPI Thermal Zone Driver thermal:02: resuming
ACPI Thermal Zone Driver thermal:03: resuming
pci 0000:00:00.0: resuming
pci 0000:00:01.0: resuming
pcieport-driver 0000:00:04.0: resuming
PCI: Setting latency timer of device 0000:00:04.0 to 64
pcieport-driver 0000:00:05.0: resuming
PCI: Setting latency timer of device 0000:00:05.0 to 64
pcieport-driver 0000:00:06.0: resuming
PCI: Setting latency timer of device 0000:00:06.0 to 64
sata_sil 0000:00:12.0: resuming
ohci_hcd 0000:00:13.0: resuming
ohci_hcd 0000:00:13.0: PCI legacy resume
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: resuming
ohci_hcd 0000:00:13.1: PCI legacy resume
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: resuming
ehci_hcd 0000:00:13.2: PCI D0, from previous PCI D3
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
PM: Writing back config space on device 0000:00:13.2 at offset 1 (was 2b00007, writing 2b00017)
ehci_hcd 0000:00:13.2: lost power, restarting
usb usb1: root hub lost power or was reset
ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:13.2: MWI active
piix4_smbus 0000:00:14.0: resuming
ATIIXP_IDE 0000:00:14.1: resuming
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
HDA Intel 0000:00:14.2: resuming
PM: Writing back config space on device 0000:00:14.2 at offset f (was 10a, writing a)
PM: Writing back config space on device 0000:00:14.2 at offset 1 (was 4100006, writing 4100002)
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:14.3: resuming
pci 0000:00:14.4: resuming
PM: Writing back config space on device 0000:00:14.4 at offset 6 (was 40030200, writing 40060200)
pci 0000:00:18.0: resuming
pci 0000:00:18.1: resuming
pci 0000:00:18.2: resuming
k8temp 0000:00:18.3: resuming
pci 0000:01:05.0: resuming
bcm43xx 0000:30:00.0: resuming
bcm43xx: Resuming...
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
bcm43xx: PHY connected
bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18  02:36:27)
bcm43xx: Radio turned on
bcm43xx: Radio enabled by hardware
ata2: SATA link down (SStatus 0 SControl 300)
bcm43xx: Chip initialized
bcm43xx: 32-bit DMA initialized
bcm43xx: Keys cleared
bcm43xx: Selected 802.11 core (phytype 2)
PM: Adding info for No Bus:hw_random
bcm43xx: Device resumed.
tg3 0000:02:01.0: resuming
PM: Writing back config space on device 0000:02:01.0 at offset b (was 3ed173b, writing 30b0103c)
PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, writing 4010)
PM: Writing back config space on device 0000:02:01.0 at offset 2 (was 2000000, writing 2000003)
PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2b00000, writing 2b00006)
PM: Writing back config space on device 0000:02:01.0 at offset 0 (was 3ed173b, writing 169c14e4)
SoftMAC: Associate: Scanning for networks first.
yenta_cardbus 0000:02:04.0: resuming
PM: Writing back config space on device 0000:02:04.0 at offset f (was 3c4010a, writing 5c0010a)
PM: Writing back config space on device 0000:02:04.0 at offset 3 (was 824010, writing 82a810)
ohci1394 0000:02:04.1: resuming
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
tifm_7xx1 0000:02:04.2: resuming
ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
sdhci 0000:02:04.3: resuming
ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
pcspkr pcspkr: resuming
pci_express 0000:00:04.0:pcie00: resuming
pci_express 0000:00:04.0:pcie01: resuming
pci_express 0000:00:04.0:pcie03: resuming
pci_express 0000:00:05.0:pcie00: resuming
pci_express 0000:00:05.0:pcie01: resuming
pci_express 0000:00:05.0:pcie03: resuming
pci_express 0000:00:06.0:pcie00: resuming
pci_express 0000:00:06.0:pcie01: resuming
pci_express 0000:00:06.0:pcie03: resuming
vesafb vesafb.0: resuming
serial8250 serial8250: resuming
sd 0:0:0:0: resuming
i8042 i8042: resuming
atkbd serio0: resuming
serio serio1: resuming
serio serio2: resuming
serio serio3: resuming
psmouse serio4: resuming
synaptics reset failed
synaptics reset failed
synaptics reset failed
SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
ide-cdrom 0.0: resuming
usb usb1: resuming
usb usb1: usb resume
usb usb1: finish resume
hub 1-0:1.0: hub_resume
ehci_hcd 0000:00:13.2: resume root hub after power loss
usb usb2: resuming
usb usb2: usb resume
usb usb2: finish resume
hub 2-0:1.0: hub_resume
ohci_hcd 0000:00:13.0: BIOS/SMM active, control 008
usb usb2: root hub lost power or was reset
ohci_hcd 0000:00:13.0: resetting from state 'reset', control = 0x8
ohci_hcd 0000:00:13.0: OHCI controller state
ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.0: hcca frame #0005
ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:13.0: restart complete
hub 2-0:1.0: resuming
usb usb3: resuming
usb usb3: usb resume
usb usb3: finish resume
hub 3-0:1.0: hub_resume
ohci_hcd 0000:00:13.1: BIOS/SMM active, control 008
usb usb3: root hub lost power or was reset
ohci_hcd 0000:00:13.1: resetting from state 'reset', control = 0x8
ohci_hcd 0000:00:13.1: OHCI controller state
ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
ohci_hcd 0000:00:13.1: hcca frame #0005
ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00010100 CSC PPS
ohci_hcd 0000:00:13.1: restart complete
hub 3-0:1.0: resuming
platform bluetooth: resuming
serio serio6: resuming
usb 2-2: resuming
 usbdev2.10_ep00: PM: resume from 0, parent 2-2 still 1
hci_usb 2-2:1.0: PM: resume from 1, parent 2-2 still 1
hci_usb 2-2:1.0: resuming
 hci0: PM: resume from 0, parent 2-2:1.0 still 1
 usbdev2.10_ep81: PM: resume from 0, parent 2-2:1.0 still 1
 usbdev2.10_ep82: PM: resume from 0, parent 2-2:1.0 still 1
 usbdev2.10_ep02: PM: resume from 0, parent 2-2:1.0 still 1
hci_usb 2-2:1.1: PM: resume from 1, parent 2-2 still 1
hci_usb 2-2:1.1: resuming
 usbdev2.10_ep83: PM: resume from 0, parent 2-2:1.1 still 1
 usbdev2.10_ep03: PM: resume from 0, parent 2-2:1.1 still 1
usb 2-2:1.2: PM: resume from 1, parent 2-2 still 1
usb 2-2:1.2: resuming
 usbdev2.10_ep84: PM: resume from 0, parent 2-2:1.2 still 1
 usbdev2.10_ep04: PM: resume from 0, parent 2-2:1.2 still 1
usb 2-2:1.3: PM: resume from 1, parent 2-2 still 1
usb 2-2:1.3: resuming
 usbdev2.10: PM: resume from 0, parent 2-2 still 1
 usbdev3.18_ep00: PM: resume from 0, parent 3-1 still 2
 usbdev3.18_ep81: PM: resume from 0, parent 3-1:1.0 still 2
 usbdev3.18_ep02: PM: resume from 0, parent 3-1:1.0 still 2
 usbdev3.18: PM: resume from 0, parent 3-1 still 2
usb 3-4: resuming
 usbdev3.19_ep00: PM: resume from 0, parent 3-4 still 1
usbhid 3-4:1.0: PM: resume from 1, parent 3-4 still 1
usbhid 3-4:1.0: resuming
 usbdev3.19_ep81: PM: resume from 0, parent 3-4:1.0 still 1
 usbdev3.19: PM: resume from 0, parent 3-4 still 1
Restarting tasks ... <7>hub 2-0:1.0: state 7 ports 4 chg 0004 evt 001e
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
done.
PM: Removing info for No Bus:vcs8
PM: Removing info for No Bus:vcsa8
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/100
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
hub 2-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
usb 2-2: USB disconnect, address 10
usb 2-2: unregistering device
usb 2-2: usb_disable_device nuking all URBs
usb 2-2: unregistering interface 2-2:1.0
PM: Removing info for No Bus:usbdev2.10_ep81
 usbdev2.10_ep81: ep_device_release called for usbdev2.10_ep81
PM: Removing info for No Bus:usbdev2.10_ep82
 usbdev2.10_ep82: ep_device_release called for usbdev2.10_ep82
PM: Removing info for No Bus:usbdev2.10_ep02
 usbdev2.10_ep02: ep_device_release called for usbdev2.10_ep02
PM: Removing info for No Bus:hci0
PM: Removing info for usb:2-2:1.0
usb 2-2:1.0: uevent
usb 2-2: unregistering interface 2-2:1.1
PM: Removing info for No Bus:usbdev2.10_ep83
 usbdev2.10_ep83: ep_device_release called for usbdev2.10_ep83
PM: Removing info for No Bus:usbdev2.10_ep03
 usbdev2.10_ep03: ep_device_release called for usbdev2.10_ep03
PM: Removing info for usb:2-2:1.1
usb 2-2:1.1: uevent
usb 2-2: unregistering interface 2-2:1.2
PM: Removing info for No Bus:usbdev2.10_ep84
 usbdev2.10_ep84: ep_device_release called for usbdev2.10_ep84
PM: Removing info for No Bus:usbdev2.10_ep04
 usbdev2.10_ep04: ep_device_release called for usbdev2.10_ep04
PM: Removing info for usb:2-2:1.2
usb 2-2:1.2: uevent
usb 2-2: unregistering interface 2-2:1.3
PM: Removing info for usb:2-2:1.3
usb 2-2:1.3: uevent
PM: Removing info for No Bus:usbdev2.10
PM: Removing info for No Bus:usbdev2.10_ep00
 usbdev2.10_ep00: ep_device_release called for usbdev2.10_ep00
PM: Removing info for usb:2-2
usb 2-2: uevent
SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 7 ports 4 chg 0012 evt 001e
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
hub 3-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
usb 3-1: USB disconnect, address 18
usb 3-1: unregistering device
usb 3-1: usb_disable_device nuking all URBs
usb 3-1: unregistering interface 3-1:1.0
PM: Removing info for No Bus:usbdev3.18_ep81
 usbdev3.18_ep81: ep_device_release called for usbdev3.18_ep81
PM: Removing info for No Bus:usbdev3.18_ep02
 usbdev3.18_ep02: ep_device_release called for usbdev3.18_ep02
PM: Removing info for usb:3-1:1.0
usb 3-1:1.0: uevent
PM: Removing info for No Bus:usbdev3.18
PM: Removing info for No Bus:usbdev3.18_ep00
 usbdev3.18_ep00: ep_device_release called for usbdev3.18_ep00
PM: Removing info for usb:3-1
usb 3-1: uevent
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
hub 3-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
hub 3-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
hub 3-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
usb 3-4: USB disconnect, address 19
usb 3-4: unregistering device
usb 3-4: usb_disable_device nuking all URBs
usb 3-4: unregistering interface 3-4:1.0
PM: Removing info for No Bus:usbdev3.19_ep81
 usbdev3.19_ep81: ep_device_release called for usbdev3.19_ep81
PM: Removing info for usb:3-4:1.0
usb 3-4:1.0: uevent
PM: Removing info for No Bus:usbdev3.19
PM: Removing info for No Bus:usbdev3.19_ep00
 usbdev3.19_ep00: ep_device_release called for usbdev3.19_ep00
PM: Removing info for usb:3-4
usb 3-4: uevent
hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 010c
ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 2 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 3 full speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
hub 1-0:1.0: port 3 not reset yet, waiting 50ms
ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
ehci_hcd 0000:00:13.2: GetStatus port 8 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 8, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:13.2: port 8 low speed --> companion
ehci_hcd 0000:00:13.2: GetStatus port 8 status 003002 POWER OWNER sig=se0 CSC
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: new full speed USB device using ohci_hcd and address 11
ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: HP Integrated Module
usb 2-2: Manufacturer: Broadcom Corp
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
PM: Adding info for No Bus:usbdev2.11_ep00
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
hci_usb 2-2:1.0: usb_probe_interface
hci_usb 2-2:1.0: usb_probe_interface - got id
PM: Adding info for No Bus:hci0
PM: Adding info for No Bus:usbdev2.11_ep81
PM: Adding info for No Bus:usbdev2.11_ep82
PM: Adding info for No Bus:usbdev2.11_ep02
usb 2-2: adding 2-2:1.1 (config #1, interface 1)
PM: Adding info for usb:2-2:1.1
usb 2-2:1.1: uevent
PM: Adding info for No Bus:usbdev2.11_ep83
PM: Adding info for No Bus:usbdev2.11_ep03
usb 2-2: adding 2-2:1.2 (config #1, interface 2)
PM: Adding info for usb:2-2:1.2
usb 2-2:1.2: uevent
hci_usb 2-2:1.2: usb_probe_interface
hci_usb 2-2:1.2: usb_probe_interface - got id
PM: Adding info for No Bus:usbdev2.11_ep84
PM: Adding info for No Bus:usbdev2.11_ep04
usb 2-2: adding 2-2:1.3 (config #1, interface 3)
PM: Adding info for usb:2-2:1.3
usb 2-2:1.3: uevent
hci_usb 2-2:1.3: usb_probe_interface
hci_usb 2-2:1.3: usb_probe_interface - got id
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0012
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 3-1: new full speed USB device using ohci_hcd and address 20
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
usb 3-1: ep0 maxpacket = 8
usb 3-1: default language 0x0409
usb 3-1: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 3-1: Product: Fingerprint Sensor
PM: Adding info for usb:3-1
usb 3-1: uevent
usb 3-1: usb_probe_device
PM: Adding info for No Bus:usbdev3.20_ep00
usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: adding 3-1:1.0 (config #1, interface 0)
PM: Adding info for usb:3-1:1.0
usb 3-1:1.0: uevent
PM: Adding info for No Bus:usbdev3.20_ep81
PM: Adding info for No Bus:usbdev3.20_ep02
PM: Adding info for No Bus:usbdev3.20
drivers/usb/core/inode.c: creating file '020'
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010301 CSC LSDA PPS CCS
hub 3-0:1.0: port 4, status 0301, change 0001, 1.5 Mb/s
hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-4: new low speed USB device using ohci_hcd and address 21
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
usb 3-4: skipped 1 descriptor after interface
usb 3-4: default language 0x0409
usb 3-4: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-4: Product: USB Receiver
usb 3-4: Manufacturer: Logitech
PM: Adding info for usb:3-4
usb 3-4: uevent
usb 3-4: usb_probe_device
PM: Adding info for No Bus:usbdev3.21_ep00
usb 3-4: configuration #1 chosen from 1 choice
usb 3-4: adding 3-4:1.0 (config #1, interface 0)
PM: Adding info for usb:3-4:1.0
usb 3-4:1.0: uevent
usbhid 3-4:1.0: usb_probe_interface
usbhid 3-4:1.0: usb_probe_interface - got id
  INPUT[INPUT]
    Field(0)
      Physical(GenericDesktop.Pointer)
      Usage(8)
        Button.0001
        Button.0002
        Button.0003
        Button.0004
        Button.0005
        Button.0006
        Button.0007
        Button.0008
      Logical Minimum(0)
      Logical Maximum(1)
      Report Size(1)
      Report Count(8)
      Report Offset(0)
      Flags( Variable Absolute )
    Field(1)
      Physical(GenericDesktop.Pointer)
      Usage(3)
        GenericDesktop.X
        GenericDesktop.Y
        GenericDesktop.Wheel
      Logical Minimum(-127)
      Logical Maximum(127)
      Report Size(8)
      Report Count(3)
      Report Offset(8)
      Flags( Variable Relative )
    Field(2)
      Physical(GenericDesktop.Pointer)
      Usage(1)
        Consumer.HorizontalWheel
      Logical Minimum(-127)
      Logical Maximum(127)
      Report Size(8)
      Report Count(1)
      Report Offset(32)
      Flags( Variable Relative )
    Field(3)
      Usage(8)
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
        LED.GenericIndicator
      Logical Minimum(0)
      Logical Maximum(1)
      Report Size(1)
      Report Count(8)
      Report Offset(40)
      Flags( Variable Absolute )
    Field(4)
      Usage(8)
        Button.0009
        Button.000a
        Button.000b
        Button.000c
        Button.000d
        Button.000e
        Button.000f
        Button.0010
      Logical Minimum(0)
      Logical Maximum(1)
      Report Size(1)
      Report Count(8)
      Report Offset(48)
      Flags( Variable Absolute )
  FEATURE[FEATURE]
    Field(0)
      Usage(1)
        GenericDesktop.MotionWakeup
      Logical Minimum(0)
      Logical Maximum(1)
      Report Size(1)
      Report Count(1)
      Report Offset(0)
      Flags( Variable Absolute NoPrefferedState )
Mapping: Button.0001 ---> Key.LeftBtn
Mapping: Button.0002 ---> Key.RightBtn
Mapping: Button.0003 ---> Key.MiddleBtn
Mapping: Button.0004 ---> Key.SideBtn
Mapping: Button.0005 ---> Key.ExtraBtn
Mapping: Button.0006 ---> Key.ForwardBtn
Mapping: Button.0007 ---> Key.BackBtn
Mapping: Button.0008 ---> Key.TaskBtn
Mapping: GenericDesktop.X ---> Relative.X
Mapping: GenericDesktop.Y ---> Relative.Y
Mapping: GenericDesktop.Wheel ---> Relative.Wheel
Mapping: Consumer.HorizontalWheel ---> Relative.HWheel
Mapping: LED.GenericIndicator ---> LED.Misc
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: LED.GenericIndicator ---> LED.?
Mapping: Button.0009 ---> Key.?
Mapping: Button.000a ---> Key.?
Mapping: Button.000b ---> Key.?
Mapping: Button.000c ---> Key.?
Mapping: Button.000d ---> Key.?
Mapping: Button.000e ---> Key.?
Mapping: Button.000f ---> Key.?
Mapping: Button.0010 ---> Key.?
input: Logitech USB Receiver as /class/input/input16
hid-pidff: starting pid init
hid-pidff: not a PID device, no output report
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-4
PM: Adding info for No Bus:usbdev3.21_ep81
PM: Adding info for No Bus:usbdev3.21
drivers/usb/core/inode.c: creating file '021'
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0100
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002
usb 3-1: usb auto-suspend
SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
hub 1-0:1.0: hub_suspend
usb usb1: usb auto-suspend
SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
PM: Removing info for No Bus:hw_random
bcm43xx: Radio turned off
bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
bcm43xx: DMA-32 0x0220 (TX) max used slots: 56/512
bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
PM: Adding info for No Bus:0000:30:00.0
PM: Removing info for No Bus:0000:30:00.0
PM: Adding info for No Bus:0000:30:00.0
PM: Removing info for No Bus:0000:30:00.0
PM: Adding info for No Bus:0000:30:00.0
PM: Removing info for No Bus:0000:30:00.0
PM: Adding info for No Bus:0000:30:00.0
PM: Removing info for No Bus:0000:30:00.0
bcm43xx: IRQ_READY timeout
bcm43xx: core_up for active 802.11 core failed (-19)
usb 3-1: usb auto-resume
ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00040103 PSSC PPS PES CCS
usb 3-1: finish resume
usb usb1: usb auto-resume
usb usb1: finish resume
hub 1-0:1.0: hub_resume
ehci_hcd 0000:00:13.2: resume root hub
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
usb 3-1: usb auto-suspend
hub 1-0:1.0: hub_suspend
usb usb1: usb auto-suspend