All of lore.kernel.org
 help / color / mirror / Atom feed
From: Antoine Tenart <antoine.tenart@free-electrons.com>
To: davem@davemloft.net, kishon@ti.com, andrew@lunn.ch,
	jason@lakedaemon.net, sebastian.hesselbarth@gmail.com,
	gregory.clement@free-electrons.com
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>,
	thomas.petazzoni@free-electrons.com, nadavh@marvell.com,
	linux@armlinux.org.uk, linux-kernel@vger.kernel.org,
	mw@semihalf.com, stefanc@marvell.com,
	miquel.raynal@free-electrons.com, netdev@vger.kernel.org
Subject: [PATCH net-next v3 02/13] phy: add the mvebu cp110 comphy driver
Date: Mon, 28 Aug 2017 16:57:14 +0200	[thread overview]
Message-ID: <20170828145725.2539-3-antoine.tenart@free-electrons.com> (raw)
In-Reply-To: <20170828145725.2539-1-antoine.tenart@free-electrons.com>

On the CP110 unit, which can be found on various Marvell platforms such
as the 7k and 8k (currently), a comphy (common PHYs) hardware block can
be found. This block provides a number of PHYs which can be used in
various modes by other controllers (network, SATA ...). These common
PHYs must be configured for the controllers using them to work correctly
either at boot time, or when the system runs to switch the mode used.
This patch adds a driver for this comphy hardware block, providing
callbacks for the its PHYs so that consumers can configure the modes
used.

As of this commit, two modes are supported by the comphy driver: sgmii
and 10gkr.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
---
 drivers/phy/marvell/Kconfig                  |  10 +
 drivers/phy/marvell/Makefile                 |   1 +
 drivers/phy/marvell/phy-mvebu-cp110-comphy.c | 656 +++++++++++++++++++++++++++
 3 files changed, 667 insertions(+)
 create mode 100644 drivers/phy/marvell/phy-mvebu-cp110-comphy.c

diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
index 048d8893bc2e..26755f3d1a9a 100644
--- a/drivers/phy/marvell/Kconfig
+++ b/drivers/phy/marvell/Kconfig
@@ -21,6 +21,16 @@ config PHY_BERLIN_USB
 	help
 	  Enable this to support the USB PHY on Marvell Berlin SoCs.
 
+config PHY_MVEBU_CP110_COMPHY
+	tristate "Marvell CP110 comphy driver"
+	depends on ARCH_MVEBU && OF
+	select GENERIC_PHY
+	help
+	  This driver allows to control the comphy, an hardware block providing
+	  shared serdes PHYs on Marvell Armada 7k/8k (in the CP110). Its serdes
+	  lanes can be used by various controllers (Ethernet, sata, usb,
+	  PCIe...).
+
 config PHY_MVEBU_SATA
 	def_bool y
 	depends on ARCH_DOVE || MACH_DOVE || MACH_KIRKWOOD
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
index 3fc188f59118..0cf6a7cbaf9f 100644
--- a/drivers/phy/marvell/Makefile
+++ b/drivers/phy/marvell/Makefile
@@ -1,6 +1,7 @@
 obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
 obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
new file mode 100644
index 000000000000..41556e790856
--- /dev/null
+++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
@@ -0,0 +1,656 @@
+/*
+ * Copyright (C) 2017 Marvell
+ *
+ * Antoine Tenart <antoine.tenart@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* Relative to priv->base */
+#define MVEBU_COMPHY_SERDES_CFG0(n)		(0x0 + (n) * 0x1000)
+#define     MVEBU_COMPHY_SERDES_CFG0_PU_PLL	BIT(1)
+#define     MVEBU_COMPHY_SERDES_CFG0_GEN_RX(n)	((n) << 3)
+#define     MVEBU_COMPHY_SERDES_CFG0_GEN_TX(n)	((n) << 7)
+#define     MVEBU_COMPHY_SERDES_CFG0_PU_RX	BIT(11)
+#define     MVEBU_COMPHY_SERDES_CFG0_PU_TX	BIT(12)
+#define     MVEBU_COMPHY_SERDES_CFG0_HALF_BUS	BIT(14)
+#define MVEBU_COMPHY_SERDES_CFG1(n)		(0x4 + (n) * 0x1000)
+#define     MVEBU_COMPHY_SERDES_CFG1_RESET	BIT(3)
+#define     MVEBU_COMPHY_SERDES_CFG1_RX_INIT	BIT(4)
+#define     MVEBU_COMPHY_SERDES_CFG1_CORE_RESET	BIT(5)
+#define     MVEBU_COMPHY_SERDES_CFG1_RF_RESET	BIT(6)
+#define MVEBU_COMPHY_SERDES_CFG2(n)		(0x8 + (n) * 0x1000)
+#define     MVEBU_COMPHY_SERDES_CFG2_DFE_EN	BIT(4)
+#define MVEBU_COMPHY_SERDES_STATUS0(n)		(0x18 + (n) * 0x1000)
+#define     MVEBU_COMPHY_SERDES_STATUS0_TX_PLL_RDY	BIT(2)
+#define     MVEBU_COMPHY_SERDES_STATUS0_RX_PLL_RDY	BIT(3)
+#define     MVEBU_COMPHY_SERDES_STATUS0_RX_INIT		BIT(4)
+#define MVEBU_COMPHY_PWRPLL_CTRL(n)		(0x804 + (n) * 0x1000)
+#define     MVEBU_COMPHY_PWRPLL_CTRL_RFREQ(n)	((n) << 0)
+#define     MVEBU_COMPHY_PWRPLL_PHY_MODE(n)	((n) << 5)
+#define MVEBU_COMPHY_IMP_CAL(n)			(0x80c + (n) * 0x1000)
+#define     MVEBU_COMPHY_IMP_CAL_TX_EXT(n)	((n) << 10)
+#define     MVEBU_COMPHY_IMP_CAL_TX_EXT_EN	BIT(15)
+#define MVEBU_COMPHY_DFE_RES(n)			(0x81c + (n) * 0x1000)
+#define     MVEBU_COMPHY_DFE_RES_FORCE_GEN_TBL	BIT(15)
+#define MVEBU_COMPHY_COEF(n)			(0x828 + (n) * 0x1000)
+#define     MVEBU_COMPHY_COEF_DFE_EN		BIT(14)
+#define     MVEBU_COMPHY_COEF_DFE_CTRL		BIT(15)
+#define MVEBU_COMPHY_GEN1_S0(n)			(0x834 + (n) * 0x1000)
+#define     MVEBU_COMPHY_GEN1_S0_TX_AMP(n)	((n) << 1)
+#define     MVEBU_COMPHY_GEN1_S0_TX_EMPH(n)	((n) << 7)
+#define MVEBU_COMPHY_GEN1_S1(n)			(0x838 + (n) * 0x1000)
+#define     MVEBU_COMPHY_GEN1_S1_RX_MUL_PI(n)	((n) << 0)
+#define     MVEBU_COMPHY_GEN1_S1_RX_MUL_PF(n)	((n) << 3)
+#define     MVEBU_COMPHY_GEN1_S1_RX_MUL_FI(n)	((n) << 6)
+#define     MVEBU_COMPHY_GEN1_S1_RX_MUL_FF(n)	((n) << 8)
+#define     MVEBU_COMPHY_GEN1_S1_RX_DFE_EN	BIT(10)
+#define     MVEBU_COMPHY_GEN1_S1_RX_DIV(n)	((n) << 11)
+#define MVEBU_COMPHY_GEN1_S2(n)			(0x8f4 + (n) * 0x1000)
+#define     MVEBU_COMPHY_GEN1_S2_TX_EMPH(n)	((n) << 0)
+#define     MVEBU_COMPHY_GEN1_S2_TX_EMPH_EN	BIT(4)
+#define MVEBU_COMPHY_LOOPBACK(n)		(0x88c + (n) * 0x1000)
+#define     MVEBU_COMPHY_LOOPBACK_DBUS_WIDTH(n)	((n) << 1)
+#define MVEBU_COMPHY_VDD_CAL0(n)		(0x908 + (n) * 0x1000)
+#define     MVEBU_COMPHY_VDD_CAL0_CONT_MODE	BIT(15)
+#define MVEBU_COMPHY_EXT_SELV(n)		(0x914 + (n) * 0x1000)
+#define     MVEBU_COMPHY_EXT_SELV_RX_SAMPL(n)	((n) << 5)
+#define MVEBU_COMPHY_MISC_CTRL0(n)		(0x93c + (n) * 0x1000)
+#define     MVEBU_COMPHY_MISC_CTRL0_ICP_FORCE	BIT(5)
+#define     MVEBU_COMPHY_MISC_CTRL0_REFCLK_SEL	BIT(10)
+#define MVEBU_COMPHY_RX_CTRL1(n)		(0x940 + (n) * 0x1000)
+#define     MVEBU_COMPHY_RX_CTRL1_RXCLK2X_SEL	BIT(11)
+#define     MVEBU_COMPHY_RX_CTRL1_CLK8T_EN	BIT(12)
+#define MVEBU_COMPHY_SPEED_DIV(n)		(0x954 + (n) * 0x1000)
+#define     MVEBU_COMPHY_SPEED_DIV_TX_FORCE	BIT(7)
+#define MVEBU_SP_CALIB(n)			(0x96c + (n) * 0x1000)
+#define     MVEBU_SP_CALIB_SAMPLER(n)		((n) << 8)
+#define     MVEBU_SP_CALIB_SAMPLER_EN		BIT(12)
+#define MVEBU_COMPHY_TX_SLEW_RATE(n)		(0x974 + (n) * 0x1000)
+#define     MVEBU_COMPHY_TX_SLEW_RATE_EMPH(n)	((n) << 5)
+#define     MVEBU_COMPHY_TX_SLEW_RATE_SLC(n)	((n) << 10)
+#define MVEBU_COMPHY_DLT_CTRL(n)		(0x984 + (n) * 0x1000)
+#define     MVEBU_COMPHY_DLT_CTRL_DTL_FLOOP_EN	BIT(2)
+#define MVEBU_COMPHY_FRAME_DETECT0(n)		(0xa14 + (n) * 0x1000)
+#define     MVEBU_COMPHY_FRAME_DETECT0_PATN(n)	((n) << 7)
+#define MVEBU_COMPHY_FRAME_DETECT3(n)		(0xa20 + (n) * 0x1000)
+#define     MVEBU_COMPHY_FRAME_DETECT3_LOST_TIMEOUT_EN	BIT(12)
+#define MVEBU_COMPHY_DME(n)			(0xa28 + (n) * 0x1000)
+#define     MVEBU_COMPHY_DME_ETH_MODE		BIT(7)
+#define MVEBU_COMPHY_TRAINING0(n)		(0xa68 + (n) * 0x1000)
+#define     MVEBU_COMPHY_TRAINING0_P2P_HOLD	BIT(15)
+#define MVEBU_COMPHY_TRAINING5(n)		(0xaa4 + (n) * 0x1000)
+#define	    MVEBU_COMPHY_TRAINING5_RX_TIMER(n)	((n) << 0)
+#define MVEBU_COMPHY_TX_TRAIN_PRESET(n)		(0xb1c + (n) * 0x1000)
+#define     MVEBU_COMPHY_TX_TRAIN_PRESET_16B_AUTO_EN	BIT(8)
+#define     MVEBU_COMPHY_TX_TRAIN_PRESET_PRBS11		BIT(9)
+#define MVEBU_COMPHY_GEN1_S3(n)			(0xc40 + (n) * 0x1000)
+#define     MVEBU_COMPHY_GEN1_S3_FBCK_SEL	BIT(9)
+#define MVEBU_COMPHY_GEN1_S4(n)			(0xc44 + (n) * 0x1000)
+#define	    MVEBU_COMPHY_GEN1_S4_DFE_RES(n)	((n) << 8)
+#define MVEBU_COMPHY_TX_PRESET(n)		(0xc68 + (n) * 0x1000)
+#define     MVEBU_COMPHY_TX_PRESET_INDEX(n)	((n) << 0)
+#define MVEBU_COMPHY_GEN1_S5(n)			(0xd38 + (n) * 0x1000)
+#define     MVEBU_COMPHY_GEN1_S5_ICP(n)		((n) << 0)
+
+/* Relative to priv->regmap */
+#define MVEBU_COMPHY_CONF1(n)			(0x1000 + (n) * 0x28)
+#define     MVEBU_COMPHY_CONF1_PWRUP		BIT(1)
+#define     MVEBU_COMPHY_CONF1_USB_PCIE		BIT(2)	/* 0: Ethernet/SATA */
+#define MVEBU_COMPHY_CONF6(n)			(0x1014 + (n) * 0x28)
+#define     MVEBU_COMPHY_CONF6_40B		BIT(18)
+#define MVEBU_COMPHY_SELECTOR			0x1140
+#define     MVEBU_COMPHY_SELECTOR_PHY(n)	((n) * 0x4)
+
+#define MVEBU_COMPHY_LANES	6
+#define MVEBU_COMPHY_PORTS	3
+
+struct mvebu_comhy_conf {
+	enum phy_mode mode;
+	unsigned lane;
+	unsigned port;
+	u32 mux;
+};
+
+#define MVEBU_COMPHY_CONF(_lane, _port, _mode, _mux)	\
+	{						\
+		.lane = _lane,				\
+		.port = _port,				\
+		.mode = _mode,				\
+		.mux = _mux,				\
+	}
+
+static const struct mvebu_comhy_conf mvebu_comphy_cp110_modes[] = {
+	/* lane 0 */
+	MVEBU_COMPHY_CONF(0, 1, PHY_MODE_SGMII, 0x1),
+	/* lane 1 */
+	MVEBU_COMPHY_CONF(1, 2, PHY_MODE_SGMII, 0x1),
+	/* lane 2 */
+	MVEBU_COMPHY_CONF(2, 0, PHY_MODE_SGMII, 0x1),
+	MVEBU_COMPHY_CONF(2, 0, PHY_MODE_10GKR, 0x1),
+	/* lane 3 */
+	MVEBU_COMPHY_CONF(3, 1, PHY_MODE_SGMII, 0x2),
+	/* lane 4 */
+	MVEBU_COMPHY_CONF(4, 0, PHY_MODE_SGMII, 0x2),
+	MVEBU_COMPHY_CONF(4, 0, PHY_MODE_10GKR, 0x2),
+	MVEBU_COMPHY_CONF(4, 1, PHY_MODE_SGMII, 0x1),
+	/* lane 5 */
+	MVEBU_COMPHY_CONF(5, 2, PHY_MODE_SGMII, 0x1),
+};
+
+struct mvebu_comphy_priv {
+	void __iomem *base;
+	struct regmap *regmap;
+	struct device *dev;
+	struct phy *phys[MVEBU_COMPHY_LANES];
+	int modes[MVEBU_COMPHY_LANES];
+};
+
+struct mvebu_comphy_lane {
+	struct mvebu_comphy_priv *priv;
+	struct device_node *of_node;
+	unsigned id;
+	enum phy_mode mode;
+	int port;
+};
+
+static int mvebu_comphy_get_mux(int lane, int port, enum phy_mode mode)
+{
+	int i, n = ARRAY_SIZE(mvebu_comphy_cp110_modes);
+
+	/* Unused PHY mux value is 0x0 */
+	if (mode == PHY_MODE_INVALID)
+		return 0;
+
+	for (i = 0; i < n; i++) {
+		if (mvebu_comphy_cp110_modes[i].lane == lane &&
+		    mvebu_comphy_cp110_modes[i].port == port &&
+		    mvebu_comphy_cp110_modes[i].mode == mode)
+			break;
+	}
+
+	if (i == n)
+		return -EINVAL;
+
+	return mvebu_comphy_cp110_modes[i].mux;
+}
+
+static void mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane,
+					     enum phy_mode mode)
+{
+	struct mvebu_comphy_priv *priv = lane->priv;
+	u32 val;
+
+	regmap_read(priv->regmap, MVEBU_COMPHY_CONF1(lane->id), &val);
+	val &= ~MVEBU_COMPHY_CONF1_USB_PCIE;
+	val |= MVEBU_COMPHY_CONF1_PWRUP;
+	regmap_write(priv->regmap, MVEBU_COMPHY_CONF1(lane->id), val);
+
+	/* Select baud rates and PLLs */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG0(lane->id));
+	val &= ~(MVEBU_COMPHY_SERDES_CFG0_PU_PLL |
+		 MVEBU_COMPHY_SERDES_CFG0_PU_RX |
+		 MVEBU_COMPHY_SERDES_CFG0_PU_TX |
+		 MVEBU_COMPHY_SERDES_CFG0_HALF_BUS |
+		 MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xf) |
+		 MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xf));
+	if (mode == PHY_MODE_10GKR)
+		val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xe) |
+		       MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xe);
+	else if (mode == PHY_MODE_SGMII)
+		val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0x6) |
+		       MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0x6) |
+		       MVEBU_COMPHY_SERDES_CFG0_HALF_BUS;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG0(lane->id));
+
+	/* reset */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val &= ~(MVEBU_COMPHY_SERDES_CFG1_RESET |
+		 MVEBU_COMPHY_SERDES_CFG1_CORE_RESET |
+		 MVEBU_COMPHY_SERDES_CFG1_RF_RESET);
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	/* de-assert reset */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val |= MVEBU_COMPHY_SERDES_CFG1_RESET |
+	       MVEBU_COMPHY_SERDES_CFG1_CORE_RESET;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	/* wait until clocks are ready */
+	mdelay(1);
+
+	/* exlicitly disable 40B, the bits isn't clear on reset */
+	regmap_read(priv->regmap, MVEBU_COMPHY_CONF6(lane->id), &val);
+	val &= ~MVEBU_COMPHY_CONF6_40B;
+	regmap_write(priv->regmap, MVEBU_COMPHY_CONF6(lane->id), val);
+
+	/* refclk selection */
+	val = readl(priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
+	val &= ~MVEBU_COMPHY_MISC_CTRL0_REFCLK_SEL;
+	if (mode == PHY_MODE_10GKR)
+		val |= MVEBU_COMPHY_MISC_CTRL0_ICP_FORCE;
+	writel(val, priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
+
+	/* power and pll selection */
+	val = readl(priv->base + MVEBU_COMPHY_PWRPLL_CTRL(lane->id));
+	val &= ~(MVEBU_COMPHY_PWRPLL_CTRL_RFREQ(0x1f) |
+		 MVEBU_COMPHY_PWRPLL_PHY_MODE(0x7));
+	val |= MVEBU_COMPHY_PWRPLL_CTRL_RFREQ(0x1) |
+	       MVEBU_COMPHY_PWRPLL_PHY_MODE(0x4);
+	writel(val, priv->base + MVEBU_COMPHY_PWRPLL_CTRL(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_LOOPBACK(lane->id));
+	val &= ~MVEBU_COMPHY_LOOPBACK_DBUS_WIDTH(0x7);
+	val |= MVEBU_COMPHY_LOOPBACK_DBUS_WIDTH(0x1);
+	writel(val, priv->base + MVEBU_COMPHY_LOOPBACK(lane->id));
+}
+
+static int mvebu_comphy_init_plls(struct mvebu_comphy_lane *lane,
+				  enum phy_mode mode)
+{
+	struct mvebu_comphy_priv *priv = lane->priv;
+	u32 val;
+
+	/* SERDES external config */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG0(lane->id));
+	val |= MVEBU_COMPHY_SERDES_CFG0_PU_PLL |
+	       MVEBU_COMPHY_SERDES_CFG0_PU_RX |
+	       MVEBU_COMPHY_SERDES_CFG0_PU_TX;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG0(lane->id));
+
+	/* check rx/tx pll */
+	readl_poll_timeout(priv->base + MVEBU_COMPHY_SERDES_STATUS0(lane->id),
+			   val,
+			   val & (MVEBU_COMPHY_SERDES_STATUS0_RX_PLL_RDY |
+				  MVEBU_COMPHY_SERDES_STATUS0_TX_PLL_RDY),
+			   1000, 150000);
+	if (!(val & (MVEBU_COMPHY_SERDES_STATUS0_RX_PLL_RDY |
+		     MVEBU_COMPHY_SERDES_STATUS0_TX_PLL_RDY)))
+		return -ETIMEDOUT;
+
+	/* rx init */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val |= MVEBU_COMPHY_SERDES_CFG1_RX_INIT;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	/* check rx */
+	readl_poll_timeout(priv->base + MVEBU_COMPHY_SERDES_STATUS0(lane->id),
+			   val, val & MVEBU_COMPHY_SERDES_STATUS0_RX_INIT,
+			   1000, 10000);
+	if (!(val & MVEBU_COMPHY_SERDES_STATUS0_RX_INIT))
+		return -ETIMEDOUT;
+
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val &= ~MVEBU_COMPHY_SERDES_CFG1_RX_INIT;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	return 0;
+}
+
+static int mvebu_comphy_set_mode_sgmii(struct phy *phy, enum phy_mode mode)
+{
+	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
+	struct mvebu_comphy_priv *priv = lane->priv;
+	u32 val;
+
+	mvebu_comphy_ethernet_init_reset(lane, mode);
+
+	val = readl(priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
+	val &= ~MVEBU_COMPHY_RX_CTRL1_CLK8T_EN;
+	val |= MVEBU_COMPHY_RX_CTRL1_RXCLK2X_SEL;
+	writel(val, priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_DLT_CTRL(lane->id));
+	val &= ~MVEBU_COMPHY_DLT_CTRL_DTL_FLOOP_EN;
+	writel(val, priv->base + MVEBU_COMPHY_DLT_CTRL(lane->id));
+
+	regmap_read(priv->regmap, MVEBU_COMPHY_CONF1(lane->id), &val);
+	val &= ~MVEBU_COMPHY_CONF1_USB_PCIE;
+	val |= MVEBU_COMPHY_CONF1_PWRUP;
+	regmap_write(priv->regmap, MVEBU_COMPHY_CONF1(lane->id), val);
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S0(lane->id));
+	val &= ~MVEBU_COMPHY_GEN1_S0_TX_EMPH(0xf);
+	val |= MVEBU_COMPHY_GEN1_S0_TX_EMPH(0x1);
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S0(lane->id));
+
+	return mvebu_comphy_init_plls(lane, mode);
+}
+
+static int mvebu_comphy_set_mode_10gkr(struct phy *phy, enum phy_mode mode)
+{
+	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
+	struct mvebu_comphy_priv *priv = lane->priv;
+	u32 val;
+
+	mvebu_comphy_ethernet_init_reset(lane, mode);
+
+	val = readl(priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
+	val |= MVEBU_COMPHY_RX_CTRL1_RXCLK2X_SEL |
+	       MVEBU_COMPHY_RX_CTRL1_CLK8T_EN;
+	writel(val, priv->base + MVEBU_COMPHY_RX_CTRL1(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_DLT_CTRL(lane->id));
+	val |= MVEBU_COMPHY_DLT_CTRL_DTL_FLOOP_EN;
+	writel(val, priv->base + MVEBU_COMPHY_DLT_CTRL(lane->id));
+
+	/* Speed divider */
+	val = readl(priv->base + MVEBU_COMPHY_SPEED_DIV(lane->id));
+	val |= MVEBU_COMPHY_SPEED_DIV_TX_FORCE;
+	writel(val, priv->base + MVEBU_COMPHY_SPEED_DIV(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG2(lane->id));
+	val |= MVEBU_COMPHY_SERDES_CFG2_DFE_EN;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG2(lane->id));
+
+	/* DFE resolution */
+	val = readl(priv->base + MVEBU_COMPHY_DFE_RES(lane->id));
+	val |= MVEBU_COMPHY_DFE_RES_FORCE_GEN_TBL;
+	writel(val, priv->base + MVEBU_COMPHY_DFE_RES(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S0(lane->id));
+	val &= ~(MVEBU_COMPHY_GEN1_S0_TX_AMP(0x1f) |
+		 MVEBU_COMPHY_GEN1_S0_TX_EMPH(0xf));
+	val |= MVEBU_COMPHY_GEN1_S0_TX_AMP(0x1c) |
+	       MVEBU_COMPHY_GEN1_S0_TX_EMPH(0xe);
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S0(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S2(lane->id));
+	val &= ~MVEBU_COMPHY_GEN1_S2_TX_EMPH(0xf);
+	val |= MVEBU_COMPHY_GEN1_S2_TX_EMPH_EN;
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S2(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_TX_SLEW_RATE(lane->id));
+	val |= MVEBU_COMPHY_TX_SLEW_RATE_EMPH(0x3) |
+	       MVEBU_COMPHY_TX_SLEW_RATE_SLC(0x3f);
+	writel(val, priv->base + MVEBU_COMPHY_TX_SLEW_RATE(lane->id));
+
+	/* Impedance calibration */
+	val = readl(priv->base + MVEBU_COMPHY_IMP_CAL(lane->id));
+	val &= ~MVEBU_COMPHY_IMP_CAL_TX_EXT(0x1f);
+	val |= MVEBU_COMPHY_IMP_CAL_TX_EXT(0xe) |
+	       MVEBU_COMPHY_IMP_CAL_TX_EXT_EN;
+	writel(val, priv->base + MVEBU_COMPHY_IMP_CAL(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S5(lane->id));
+	val &= ~MVEBU_COMPHY_GEN1_S5_ICP(0xf);
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S5(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S1(lane->id));
+	val &= ~(MVEBU_COMPHY_GEN1_S1_RX_MUL_PI(0x7) |
+		 MVEBU_COMPHY_GEN1_S1_RX_MUL_PF(0x7) |
+		 MVEBU_COMPHY_GEN1_S1_RX_MUL_FI(0x3) |
+		 MVEBU_COMPHY_GEN1_S1_RX_MUL_FF(0x3));
+	val |= MVEBU_COMPHY_GEN1_S1_RX_DFE_EN |
+	       MVEBU_COMPHY_GEN1_S1_RX_MUL_PI(0x2) |
+	       MVEBU_COMPHY_GEN1_S1_RX_MUL_PF(0x2) |
+	       MVEBU_COMPHY_GEN1_S1_RX_MUL_FF(0x1) |
+	       MVEBU_COMPHY_GEN1_S1_RX_DIV(0x3);
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S1(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_COEF(lane->id));
+	val &= ~(MVEBU_COMPHY_COEF_DFE_EN | MVEBU_COMPHY_COEF_DFE_CTRL);
+	writel(val, priv->base + MVEBU_COMPHY_COEF(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S4(lane->id));
+	val &= ~MVEBU_COMPHY_GEN1_S4_DFE_RES(0x3);
+	val |= MVEBU_COMPHY_GEN1_S4_DFE_RES(0x1);
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S4(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_GEN1_S3(lane->id));
+	val |= MVEBU_COMPHY_GEN1_S3_FBCK_SEL;
+	writel(val, priv->base + MVEBU_COMPHY_GEN1_S3(lane->id));
+
+	/* rx training timer */
+	val = readl(priv->base + MVEBU_COMPHY_TRAINING5(lane->id));
+	val &= ~MVEBU_COMPHY_TRAINING5_RX_TIMER(0x3ff);
+	val |= MVEBU_COMPHY_TRAINING5_RX_TIMER(0x13);
+	writel(val, priv->base + MVEBU_COMPHY_TRAINING5(lane->id));
+
+	/* tx train peak to peak hold */
+	val = readl(priv->base + MVEBU_COMPHY_TRAINING0(lane->id));
+	val |= MVEBU_COMPHY_TRAINING0_P2P_HOLD;
+	writel(val, priv->base + MVEBU_COMPHY_TRAINING0(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_TX_PRESET(lane->id));
+	val &= ~MVEBU_COMPHY_TX_PRESET_INDEX(0xf);
+	val |= MVEBU_COMPHY_TX_PRESET_INDEX(0x2);	/* preset coeff */
+	writel(val, priv->base + MVEBU_COMPHY_TX_PRESET(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_FRAME_DETECT3(lane->id));
+	val &= ~MVEBU_COMPHY_FRAME_DETECT3_LOST_TIMEOUT_EN;
+	writel(val, priv->base + MVEBU_COMPHY_FRAME_DETECT3(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_TX_TRAIN_PRESET(lane->id));
+	val |= MVEBU_COMPHY_TX_TRAIN_PRESET_16B_AUTO_EN |
+	       MVEBU_COMPHY_TX_TRAIN_PRESET_PRBS11;
+	writel(val, priv->base + MVEBU_COMPHY_TX_TRAIN_PRESET(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_FRAME_DETECT0(lane->id));
+	val &= ~MVEBU_COMPHY_FRAME_DETECT0_PATN(0x1ff);
+	val |= MVEBU_COMPHY_FRAME_DETECT0_PATN(0x88);
+	writel(val, priv->base + MVEBU_COMPHY_FRAME_DETECT0(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_DME(lane->id));
+	val |= MVEBU_COMPHY_DME_ETH_MODE;
+	writel(val, priv->base + MVEBU_COMPHY_DME(lane->id));
+
+	val = readl(priv->base + MVEBU_COMPHY_VDD_CAL0(lane->id));
+	val |= MVEBU_COMPHY_VDD_CAL0_CONT_MODE;
+	writel(val, priv->base + MVEBU_COMPHY_VDD_CAL0(lane->id));
+
+	val = readl(priv->base + MVEBU_SP_CALIB(lane->id));
+	val &= ~MVEBU_SP_CALIB_SAMPLER(0x3);
+	val |= MVEBU_SP_CALIB_SAMPLER(0x3) |
+	       MVEBU_SP_CALIB_SAMPLER_EN;
+	writel(val, priv->base + MVEBU_SP_CALIB(lane->id));
+	val &= ~MVEBU_SP_CALIB_SAMPLER_EN;
+	writel(val, priv->base + MVEBU_SP_CALIB(lane->id));
+
+	/* External rx regulator */
+	val = readl(priv->base + MVEBU_COMPHY_EXT_SELV(lane->id));
+	val &= ~MVEBU_COMPHY_EXT_SELV_RX_SAMPL(0x1f);
+	val |= MVEBU_COMPHY_EXT_SELV_RX_SAMPL(0x1a);
+	writel(val, priv->base + MVEBU_COMPHY_EXT_SELV(lane->id));
+
+	return mvebu_comphy_init_plls(lane, mode);
+}
+
+static int mvebu_comphy_power_on(struct phy *phy)
+{
+	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
+	struct mvebu_comphy_priv *priv = lane->priv;
+	int ret;
+	u32 mux, val;
+
+	mux = mvebu_comphy_get_mux(lane->id, lane->port, lane->mode);
+	if (mux < 0)
+		return -ENOTSUPP;
+
+	regmap_read(priv->regmap, MVEBU_COMPHY_SELECTOR, &val);
+	val &= ~(0xf << MVEBU_COMPHY_SELECTOR_PHY(lane->id));
+	val |= mux << MVEBU_COMPHY_SELECTOR_PHY(lane->id);
+	regmap_write(priv->regmap, MVEBU_COMPHY_SELECTOR, val);
+
+	switch (lane->mode) {
+	case PHY_MODE_SGMII:
+		ret = mvebu_comphy_set_mode_sgmii(phy, lane->mode);
+		break;
+	case PHY_MODE_10GKR:
+		ret = mvebu_comphy_set_mode_10gkr(phy, lane->mode);
+		break;
+	default:
+		return -ENOTSUPP;
+	}
+
+	/* digital reset */
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val |= MVEBU_COMPHY_SERDES_CFG1_RF_RESET;
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	return ret;
+}
+
+static int mvebu_comphy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
+
+	if (mvebu_comphy_get_mux(lane->id, lane->port, mode) < 0)
+		return -EINVAL;
+
+	lane->mode = mode;
+	return 0;
+}
+
+static int mvebu_comphy_power_off(struct phy *phy)
+{
+	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
+	struct mvebu_comphy_priv *priv = lane->priv;
+	u32 val;
+
+	val = readl(priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+	val &= ~(MVEBU_COMPHY_SERDES_CFG1_RESET |
+		 MVEBU_COMPHY_SERDES_CFG1_CORE_RESET |
+		 MVEBU_COMPHY_SERDES_CFG1_RF_RESET);
+	writel(val, priv->base + MVEBU_COMPHY_SERDES_CFG1(lane->id));
+
+	regmap_read(priv->regmap, MVEBU_COMPHY_SELECTOR, &val);
+	val &= ~(0xf << MVEBU_COMPHY_SELECTOR_PHY(lane->id));
+	regmap_write(priv->regmap, MVEBU_COMPHY_SELECTOR, val);
+
+	return 0;
+}
+
+static const struct phy_ops mvebu_comphy_ops = {
+	.power_on	= mvebu_comphy_power_on,
+	.power_off	= mvebu_comphy_power_off,
+	.set_mode	= mvebu_comphy_set_mode,
+};
+
+static struct phy *mvebu_comphy_xlate(struct device *dev,
+				      struct of_phandle_args *args)
+{
+	struct mvebu_comphy_priv *priv = dev_get_drvdata(dev);
+	struct mvebu_comphy_lane *lane;
+	int i;
+
+	if (WARN_ON(args->args[0] >= MVEBU_COMPHY_PORTS))
+		return ERR_PTR(-EINVAL);
+
+	for (i = 0; i < MVEBU_COMPHY_LANES; i++) {
+		if (!priv->phys[i])
+			continue;
+
+		lane = phy_get_drvdata(priv->phys[i]);
+		if (priv->phys[i] && args->np == lane->of_node)
+			break;
+	}
+
+	if (i == MVEBU_COMPHY_LANES)
+		return ERR_PTR(-ENODEV);
+
+	if (lane->port >= 0)
+		return ERR_PTR(-EBUSY);
+
+	lane->port = args->args[0];
+	return priv->phys[i];
+}
+
+static int mvebu_comphy_probe(struct platform_device *pdev)
+{
+	struct mvebu_comphy_priv *priv;
+	struct phy_provider *provider;
+	struct device_node *child;
+	struct resource *res;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &pdev->dev;
+	priv->regmap =
+		syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						"marvell,system-controller");
+	if (IS_ERR(priv->regmap))
+		return PTR_ERR(priv->regmap);
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, res);
+	if (!priv->base)
+		return -ENOMEM;
+
+	for_each_available_child_of_node(pdev->dev.of_node, child) {
+		struct mvebu_comphy_lane *lane;
+		struct phy *phy;
+		int ret;
+		u32 val;
+
+		ret = of_property_read_u32(child, "reg", &val);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
+				ret);
+			continue;
+		}
+
+		if (val >= MVEBU_COMPHY_LANES) {
+			dev_err(&pdev->dev, "invalid 'reg' property\n");
+			continue;
+		}
+
+		lane = devm_kzalloc(&pdev->dev, sizeof(*lane), GFP_KERNEL);
+		if (!lane)
+			return -ENOMEM;
+
+		phy = devm_phy_create(&pdev->dev, NULL, &mvebu_comphy_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		lane->priv = priv;
+		lane->of_node = child;
+		lane->mode = PHY_MODE_INVALID;
+		lane->id = val;
+		lane->port = -1;
+		phy_set_drvdata(phy, lane);
+
+		priv->phys[val] = phy;
+
+		/*
+		 * Once all modes are supported in this driver we should call
+		 * mvebu_comphy_power_off(phy) here to avoid relying on the
+		 * bootloader/firmware configuration.
+		 */
+	}
+
+	dev_set_drvdata(&pdev->dev, priv);
+	provider = devm_of_phy_provider_register(&pdev->dev,
+						 mvebu_comphy_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mvebu_comphy_of_match_table[] = {
+	{ .compatible = "marvell,comphy-cp110" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mvebu_comphy_of_match_table);
+
+static struct platform_driver mvebu_comphy_driver = {
+	.probe	= mvebu_comphy_probe,
+	.driver	= {
+		.name = "mvebu-comphy",
+		.of_match_table = mvebu_comphy_of_match_table,
+	},
+};
+module_platform_driver(mvebu_comphy_driver);
+
+MODULE_AUTHOR("Antoine Tenart <antoine.tenart@free-electrons.com>");
+MODULE_DESCRIPTION("Common PHY driver for mvebu SoCs");
+MODULE_LICENSE("GPL v2");
-- 
2.13.5

  parent reply	other threads:[~2017-08-28 14:58 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-08-28 14:57 [PATCH net-next v3 00/13] net: mvpp2: comphy configuration Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 01/13] phy: add sgmii and 10gkr modes to the phy_mode enum Antoine Tenart
2017-08-29 10:38   ` Kishon Vijay Abraham I
2017-08-29 11:27     ` Antoine Tenart
2017-08-29 12:21       ` Kishon Vijay Abraham I
2017-08-28 14:57 ` Antoine Tenart [this message]
2017-08-29 11:04   ` [PATCH net-next v3 02/13] phy: add the mvebu cp110 comphy driver Kishon Vijay Abraham I
2017-08-29 11:23     ` Antoine Tenart
2017-08-29 12:25       ` Kishon Vijay Abraham I
2017-08-29 13:12         ` Antoine Tenart
2017-08-30  5:31           ` Kishon Vijay Abraham I
2017-08-30  6:43             ` Antoine Tenart
2017-08-30  5:19   ` Kishon Vijay Abraham I
2017-08-30  6:36     ` Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 03/13] Documentation/bindings: phy: document the Marvell " Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 04/13] net: mvpp2: initialize the comphy Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 05/13] net: mvpp2: simplify the link_event function Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 06/13] net: mvpp2: improve the link management function Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 07/13] net: mvpp2: do not set GMAC autoneg when using XLG MAC Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 08/13] net: mvpp2: dynamic reconfiguration of the comphy/GoP/MAC Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 09/13] arm64: dts: marvell: extend the cp110 syscon register area length Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 10/13] arm64: dts: marvell: add comphy nodes on cp110 master and slave Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 11/13] arm64: dts: marvell: mcbin: add comphy references to Ethernet ports Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 12/13] arm64: dts: marvell: 7040-db: " Antoine Tenart
2017-08-28 14:57 ` [PATCH net-next v3 13/13] arm64: defconfig: enable Marvell CP110 comphy Antoine Tenart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170828145725.2539-3-antoine.tenart@free-electrons.com \
    --to=antoine.tenart@free-electrons.com \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=gregory.clement@free-electrons.com \
    --cc=jason@lakedaemon.net \
    --cc=kishon@ti.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=miquel.raynal@free-electrons.com \
    --cc=mw@semihalf.com \
    --cc=nadavh@marvell.com \
    --cc=netdev@vger.kernel.org \
    --cc=sebastian.hesselbarth@gmail.com \
    --cc=stefanc@marvell.com \
    --cc=thomas.petazzoni@free-electrons.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.