All of lore.kernel.org
 help / color / mirror / Atom feed
From: Alexey Ivanov <alexeyivan@gmail.com>
To: ath10k@lists.infradead.org
Subject: 
Date: Wed, 13 Jan 2016 15:34:49 +0400	[thread overview]
Message-ID: <CAGvpMW8JW+a6-MS=TrRNFvBDG4LWYFR+2fM09dFhQEes7NEn4w@mail.gmail.com> (raw)

I'm trying to run OpenWrt(r48016) with ath10k driver on this device
(https://wikidevi.com/wiki/EnGenius_EAP1750H)

The calibration data is present at 0x5000@ART. I've copied it to board.bin

But the driver fails to load:
[   10.313982] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0
irq_mode 0 reset_mode 0
[   10.526214] ath10k_pci 0000:00:00.0: Direct firmware load for
ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[   10.536740] ath10k_pci 0000:00:00.0: Falling back to user helper
[   10.611930] firmware ath10k!cal-pci-0000:00:00.0.bin:
firmware_loading_store: map pages failed
[   10.749685] ath10k_pci 0000:00:00.0: qca988x hw2.0 target
0x4100016c chip_id 0x043202ff sub 0000:0000
[   10.759085] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1
tracing 0 dfs 0 testmode 1
[   10.772154] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.97 api 5
features no-p2p crc32 f91e34f2
[   10.821280] ath10k_pci 0000:00:00.0: Direct firmware load for
ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[   10.831887] ath10k_pci 0000:00:00.0: Falling back to user helper
[   10.907421] firmware ath10k!QCA988X!hw2.0!board-2.bin:
firmware_loading_store: map pages failed
[   10.916658] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A
crc32 bebc7c08
[   11.012769] ath10k_pci 0000:00:00.0: otp calibration failed: 2
[   11.018708] ath10k_pci 0000:00:00.0: failed to run otp: -22
[   11.024367] ath10k_pci 0000:00:00.0: could not init core (-22)
[   11.030370] ath10k_pci 0000:00:00.0: could not probe fw (-22)


The output after insmod ath10k_core skip_otp=Y:

[ 1346.161436] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0
irq_mode 0 reset_mode 0
[ 1346.376382] ath10k_pci 0000:00:00.0: Direct firmware load for
ath10k/cal-pci-0000:00:00.0.bin failed with error -2
[ 1346.386932] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 1346.463861] firmware ath10k!cal-pci-0000:00:00.0.bin:
firmware_loading_store: map pages failed
[ 1346.475118] ath10k_pci 0000:00:00.0: qca988x hw2.0 target
0x4100016c chip_id 0x043202ff sub 0000:0000
[ 1346.484521] ath10k_pci 0000:00:00.0: kconfig debug 1 debugfs 1
tracing 0 dfs 0 testmode 1
[ 1346.497614] ath10k_pci 0000:00:00.0: firmware ver 10.2.4.97 api 5
features no-p2p crc32 f91e34f2
[ 1346.548363] ath10k_pci 0000:00:00.0: Direct firmware load for
ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 1346.558999] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 1346.635967] firmware ath10k!QCA988X!hw2.0!board-2.bin:
firmware_loading_store: map pages failed
[ 1346.645156] ath10k_pci 0000:00:00.0:
board_file api 1 bmi_id N/A crc32 bebc7c08
[ 1347.782528] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 5 htt-op 2
cal otp max-sta 128 raw 0 hwcrypto 1


The original QSDK version by EnGenius works good.
What am I doing wrong? Or the
board_file api 1 is not supported by ath10k?

--
Best regards,
Alex Ivanov

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

             reply	other threads:[~2016-01-13 11:35 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-01-13 11:34 Alexey Ivanov [this message]
2016-01-13 13:12 ` Michal Kazior
     [not found]   ` <CAGvpMW9d8RZGpfBd2H0W35fVUQoi9jcZvQmTC7ztW+dPVcxOhg@mail.gmail.com>
2016-01-13 14:05     ` Re: Michal Kazior
2016-01-13 14:45       ` Re: Alexey Ivanov
2016-01-13 14:54         ` Re: Michal Kazior
2016-01-14  5:36           ` Re: Alexey Ivanov
2016-01-14  7:21             ` Re: Michal Kazior
2016-01-14 11:14               ` Re: Alexey Ivanov
2016-01-14 11:26                 ` Re: Shajakhan, Mohammed Shafi (Mohammed Shafi)
2016-01-14 12:33                   ` Re: Alexey Ivanov
2016-01-14 17:45             ` Re: Peter Oh

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='CAGvpMW8JW+a6-MS=TrRNFvBDG4LWYFR+2fM09dFhQEes7NEn4w@mail.gmail.com' \
    --to=alexeyivan@gmail.com \
    --cc=ath10k@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.