From: Thierry Herbelot <thierry.herbelot@6wind.com>
To: Hemant Agrawal <hemant.agrawal@nxp.com>, dev@dpdk.org
Cc: akhil.goyal@nxp.com
Subject: Re: [dpdk-dev] [PATCH] crypto/dpaa_sec: enable compilation without security
Date: Fri, 18 Oct 2019 10:11:50 +0200 [thread overview]
Message-ID: <fb3f2bf2-5caa-448d-7fbd-240932ed52ef@6wind.com> (raw)
In-Reply-To: <20191018075613.2784-3-hemant.agrawal@nxp.com>
On 10/18/19 9:56 AM, Hemant Agrawal wrote:
> This patch enables the dpaaX_sec compilation when SECURITY
> is disabled.
>
> Signed-off-by: Hemant Agrawal <hemant.agrawal@nxp.com>
> ---
> drivers/crypto/Makefile | 4 ++--
> drivers/crypto/dpaa2_sec/dpaa2_sec_dpseci.c | 26 +++++++++++++++------
> drivers/crypto/dpaa2_sec/dpaa2_sec_priv.h | 11 +++++++--
> drivers/crypto/dpaa_sec/dpaa_sec.c | 25 ++++++++++++++------
> drivers/crypto/dpaa_sec/dpaa_sec.h | 10 ++++++--
> mk/rte.app.mk | 4 ++--
> 6 files changed, 58 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
> index 8b0085792..47a2a9e79 100644
> --- a/drivers/crypto/Makefile
> +++ b/drivers/crypto/Makefile
> @@ -16,14 +16,14 @@ DIRS-$(CONFIG_RTE_LIBRTE_PMD_KASUMI) += kasumi
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_ZUC) += zuc
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_MVSAM_CRYPTO) += mvsam
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_NULL_CRYPTO) += null
> -ifeq ($(CONFIG_RTE_LIBRTE_SECURITY),y)
> ifeq ($(CONFIG_RTE_EAL_VFIO)$(CONFIG_RTE_LIBRTE_FSLMC_BUS),yy)
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_DPAA2_SEC) += dpaa2_sec
> endif # CONFIG_RTE_LIBRTE_FSLMC_BUS
> ifeq ($(CONFIG_RTE_LIBRTE_DPAA_BUS),y)
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_DPAA_SEC) += dpaa_sec
> -DIRS-$(CONFIG_RTE_LIBRTE_PMD_CAAM_JR) += caam_jr
> endif # CONFIG_RTE_LIBRTE_PMD_DPAA_SEC
> +ifeq ($(CONFIG_RTE_LIBRTE_SECURITY),y)
> +DIRS-$(CONFIG_RTE_LIBRTE_PMD_CAAM_JR) += caam_jr
> endif # CONFIG_RTE_LIBRTE_SECURITY
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_VIRTIO_CRYPTO) += virtio
> DIRS-$(CONFIG_RTE_LIBRTE_PMD_NITROX) += nitrox
> diff --git a/drivers/crypto/dpaa2_sec/dpaa2_sec_dpseci.c b/drivers/crypto/dpaa2_sec/dpaa2_sec_dpseci.c
> index b33dbca8b..41dbbb7da 100644
> --- a/drivers/crypto/dpaa2_sec/dpaa2_sec_dpseci.c
> +++ b/drivers/crypto/dpaa2_sec/dpaa2_sec_dpseci.c
> @@ -166,6 +166,7 @@ build_proto_compound_sg_fd(dpaa2_sec_session *sess,
> ip_fle->length = in_len;
> DPAA2_SET_FLE_FIN(sge);
>
> +#ifdef RTE_LIBRTE_SECURITY
> /* In case of PDCP, per packet HFN is stored in
> * mbuf priv after sym_op.
> */
> @@ -176,6 +177,7 @@ build_proto_compound_sg_fd(dpaa2_sec_session *sess,
> DPAA2_SET_FLE_INTERNAL_JD(op_fle, hfn_ovd);
> DPAA2_SET_FD_INTERNAL_JD(fd, hfn_ovd);
> }
> +#endif
> DPAA2_SET_FD_LEN(fd, ip_fle->length);
>
> return 0;
> @@ -241,6 +243,7 @@ build_proto_compound_fd(dpaa2_sec_session *sess,
> DPAA2_SET_FD_LEN(fd, ip_fle->length);
> DPAA2_SET_FLE_FIN(ip_fle);
>
> +#ifdef RTE_LIBRTE_SECURITY
> /* In case of PDCP, per packet HFN is stored in
> * mbuf priv after sym_op.
> */
> @@ -251,7 +254,7 @@ build_proto_compound_fd(dpaa2_sec_session *sess,
> DPAA2_SET_FLE_INTERNAL_JD(op_fle, hfn_ovd);
> DPAA2_SET_FD_INTERNAL_JD(fd, hfn_ovd);
> }
> -
> +#endif
> return 0;
>
> }
> @@ -1358,9 +1361,11 @@ build_sec_fd(struct rte_crypto_op *op,
> if (op->sess_type == RTE_CRYPTO_OP_WITH_SESSION)
> sess = (dpaa2_sec_session *)get_sym_session_private_data(
> op->sym->session, cryptodev_driver_id);
> +#ifdef RTE_LIBRTE_SECURITY
> else if (op->sess_type == RTE_CRYPTO_OP_SECURITY_SESSION)
> sess = (dpaa2_sec_session *)get_sec_session_private_data(
> op->sym->sec_session);
> +#endif
> else
> return -1;
>
> @@ -1506,7 +1511,7 @@ sec_simple_fd_to_mbuf(const struct qbman_fd *fd)
> struct rte_crypto_op *op;
> uint16_t len = DPAA2_GET_FD_LEN(fd);
> uint16_t diff = 0;
> - dpaa2_sec_session *sess_priv;
> + dpaa2_sec_session *sess_priv __rte_unused;
>
> struct rte_mbuf *mbuf = DPAA2_INLINE_MBUF_FROM_BUF(
> DPAA2_IOVA_TO_VADDR(DPAA2_GET_FD_ADDR(fd)),
> @@ -1519,13 +1524,14 @@ sec_simple_fd_to_mbuf(const struct qbman_fd *fd)
> mbuf->buf_iova = op->sym->aead.digest.phys_addr;
> op->sym->aead.digest.phys_addr = 0L;
>
> +#ifdef RTE_LIBRTE_SECURITY
> sess_priv = (dpaa2_sec_session *)get_sec_session_private_data(
> op->sym->sec_session);
> if (sess_priv->dir == DIR_ENC)
> mbuf->data_off += SEC_FLC_DHR_OUTBOUND;
> else
> mbuf->data_off += SEC_FLC_DHR_INBOUND;
> -
> +#endif
> return op;
> }
>
> @@ -1569,6 +1575,7 @@ sec_fd_to_mbuf(const struct qbman_fd *fd)
> } else
> dst = src;
>
> +#ifdef RTE_LIBRTE_SECURITY
> if (op->sess_type == RTE_CRYPTO_OP_SECURITY_SESSION) {
> dpaa2_sec_session *sess = (dpaa2_sec_session *)
> get_sec_session_private_data(op->sym->sec_session);
> @@ -1583,7 +1590,7 @@ sec_fd_to_mbuf(const struct qbman_fd *fd)
> dst->data_len = len;
> }
> }
> -
> +#endif
> DPAA2_SEC_DP_DEBUG("mbuf %p BMAN buf addr %p,"
> " fdaddr =%" PRIx64 " bpid =%d meta =%d off =%d, len =%d\n",
> (void *)dst,
> @@ -2500,6 +2507,7 @@ dpaa2_sec_set_session_parameters(struct rte_cryptodev *dev,
> return ret;
> }
>
> +#ifdef RTE_LIBRTE_SECURITY
> static int
> dpaa2_sec_ipsec_aead_init(struct rte_crypto_aead_xform *aead_xform,
> dpaa2_sec_session *session,
> @@ -3172,7 +3180,7 @@ dpaa2_sec_security_session_destroy(void *dev __rte_unused,
> }
> return 0;
> }
> -
> +#endif
> static int
> dpaa2_sec_sym_session_configure(struct rte_cryptodev *dev,
> struct rte_crypto_sym_xform *xform,
> @@ -3561,6 +3569,7 @@ static struct rte_cryptodev_ops crypto_ops = {
> .sym_session_clear = dpaa2_sec_sym_session_clear,
> };
>
> +#ifdef RTE_LIBRTE_SECURITY
> static const struct rte_security_capability *
> dpaa2_sec_capabilities_get(void *device __rte_unused)
> {
> @@ -3575,6 +3584,7 @@ static const struct rte_security_ops dpaa2_sec_security_ops = {
> .set_pkt_metadata = NULL,
> .capabilities_get = dpaa2_sec_capabilities_get
> };
> +#endif
>
> static int
> dpaa2_sec_uninit(const struct rte_cryptodev *dev)
> @@ -3597,7 +3607,9 @@ dpaa2_sec_dev_init(struct rte_cryptodev *cryptodev)
> struct dpaa2_sec_dev_private *internals;
> struct rte_device *dev = cryptodev->device;
> struct rte_dpaa2_device *dpaa2_dev;
> +#ifdef RTE_LIBRTE_SECURITY
> struct rte_security_ctx *security_instance;
> +#endif
> struct fsl_mc_io *dpseci;
> uint16_t token;
> struct dpseci_attr attr;
> @@ -3638,7 +3650,7 @@ dpaa2_sec_dev_init(struct rte_cryptodev *cryptodev)
> DPAA2_SEC_DEBUG("Device already init by primary process");
> return 0;
> }
> -
> +#ifdef RTE_LIBRTE_SECURITY
> /* Initialize security_ctx only for primary process*/
> security_instance = rte_malloc("rte_security_instances_ops",
> sizeof(struct rte_security_ctx), 0);
> @@ -3648,7 +3660,7 @@ dpaa2_sec_dev_init(struct rte_cryptodev *cryptodev)
> security_instance->ops = &dpaa2_sec_security_ops;
> security_instance->sess_cnt = 0;
> cryptodev->security_ctx = security_instance;
> -
> +#endif
> /*Open the rte device via MC and save the handle for further use*/
> dpseci = (struct fsl_mc_io *)rte_calloc(NULL, 1,
> sizeof(struct fsl_mc_io), 0);
> diff --git a/drivers/crypto/dpaa2_sec/dpaa2_sec_priv.h b/drivers/crypto/dpaa2_sec/dpaa2_sec_priv.h
> index ca4fcfe9b..648bf8045 100644
> --- a/drivers/crypto/dpaa2_sec/dpaa2_sec_priv.h
> +++ b/drivers/crypto/dpaa2_sec/dpaa2_sec_priv.h
> @@ -8,7 +8,9 @@
> #ifndef _RTE_DPAA2_SEC_PMD_PRIVATE_H_
> #define _RTE_DPAA2_SEC_PMD_PRIVATE_H_
>
> +#ifdef RTE_LIBRTE_SECURITY
> #include <rte_security_driver.h>
> +#endif
>
> #define CRYPTODEV_NAME_DPAA2_SEC_PMD crypto_dpaa2_sec
> /**< NXP DPAA2 - SEC PMD device name */
> @@ -139,6 +141,7 @@ struct dpaa2_sec_aead_ctxt {
> uint8_t auth_cipher_text; /**< Authenticate/cipher ordering */
> };
>
> +#ifdef RTE_LIBRTE_SECURITY
> /*
> * The structure is to be filled by user for PDCP Protocol
> */
> @@ -154,7 +157,7 @@ struct dpaa2_pdcp_ctxt {
> uint32_t hfn; /*!< Hyper Frame Number */
> uint32_t hfn_threshold; /*!< HFN Threashold for key renegotiation */
> };
> -
> +#endif
> typedef struct dpaa2_sec_session_entry {
> void *ctxt;
> uint8_t ctxt_type;
> @@ -190,7 +193,9 @@ typedef struct dpaa2_sec_session_entry {
> struct dpaa2_sec_aead_ctxt aead_ctxt;
> } ext_params;
> };
> +#ifdef RTE_LIBRTE_SECURITY
> struct dpaa2_pdcp_ctxt pdcp;
> +#endif
> };
> } dpaa2_sec_session;
>
> @@ -504,6 +509,8 @@ static const struct rte_cryptodev_capabilities dpaa2_sec_capabilities[] = {
> RTE_CRYPTODEV_END_OF_CAPABILITIES_LIST()
> };
>
> +#ifdef RTE_LIBRTE_SECURITY
> +
> static const struct rte_cryptodev_capabilities dpaa2_pdcp_capabilities[] = {
> { /* SNOW 3G (UIA2) */
> .op = RTE_CRYPTO_OP_TYPE_SYMMETRIC,
> @@ -705,7 +712,7 @@ static const struct rte_security_capability dpaa2_sec_security_cap[] = {
> .action = RTE_SECURITY_ACTION_TYPE_NONE
> }
> };
> -
> +#endif
> /**
> * Checksum
> *
> diff --git a/drivers/crypto/dpaa_sec/dpaa_sec.c b/drivers/crypto/dpaa_sec/dpaa_sec.c
> index 7c37136fa..4adaadf5f 100644
> --- a/drivers/crypto/dpaa_sec/dpaa_sec.c
> +++ b/drivers/crypto/dpaa_sec/dpaa_sec.c
> @@ -15,7 +15,9 @@
> #include <rte_cryptodev_pmd.h>
> #include <rte_crypto.h>
> #include <rte_cryptodev.h>
> +#ifdef RTE_LIBRTE_SECURITY
> #include <rte_security_driver.h>
> +#endif
> #include <rte_cycles.h>
> #include <rte_dev.h>
> #include <rte_kvargs.h>
> @@ -252,6 +254,7 @@ static inline int is_decode(dpaa_sec_session *ses)
> return ses->dir == DIR_DEC;
> }
>
> +#ifdef RTE_LIBRTE_SECURITY
> static int
> dpaa_sec_prep_pdcp_cdb(dpaa_sec_session *ses)
> {
> @@ -355,7 +358,6 @@ dpaa_sec_prep_pdcp_cdb(dpaa_sec_session *ses)
> ses->pdcp.hfn_threshold,
> &cipherdata, p_authdata, 0);
> }
> -
> return shared_desc_len;
> }
>
> @@ -432,7 +434,7 @@ dpaa_sec_prep_ipsec_cdb(dpaa_sec_session *ses)
> }
> return shared_desc_len;
> }
> -
> +#endif
> /* prepare command block of the session */
> static int
> dpaa_sec_prep_cdb(dpaa_sec_session *ses)
> @@ -450,12 +452,14 @@ dpaa_sec_prep_cdb(dpaa_sec_session *ses)
> memset(cdb, 0, sizeof(struct sec_cdb));
>
> switch (ses->ctxt) {
> +#ifdef RTE_LIBRTE_SECURITY
> case DPAA_SEC_IPSEC:
> shared_desc_len = dpaa_sec_prep_ipsec_cdb(ses);
> break;
> case DPAA_SEC_PDCP:
> shared_desc_len = dpaa_sec_prep_pdcp_cdb(ses);
> break;
> +#endif
> case DPAA_SEC_CIPHER:
> alginfo_c.key = (size_t)ses->cipher_key.data;
> alginfo_c.keylen = ses->cipher_key.length;
> @@ -1753,11 +1757,13 @@ dpaa_sec_enqueue_burst(void *qp, struct rte_crypto_op **ops,
> op->sym->session,
> cryptodev_driver_id);
> break;
> +#ifdef RTE_LIBRTE_SECURITY
> case RTE_CRYPTO_OP_SECURITY_SESSION:
> ses = (dpaa_sec_session *)
> get_sec_session_private_data(
> op->sym->sec_session);
> break;
> +#endif
> default:
> DPAA_SEC_DP_ERR(
> "sessionless crypto op not supported");
> @@ -1877,6 +1883,7 @@ dpaa_sec_enqueue_burst(void *qp, struct rte_crypto_op **ops,
> ((auth_tail_len << 16) | auth_hdr_len);
> }
>
> +#ifdef RTE_LIBRTE_SECURITY
> /* In case of PDCP, per packet HFN is stored in
> * mbuf priv after sym_op.
> */
> @@ -1889,7 +1896,7 @@ dpaa_sec_enqueue_burst(void *qp, struct rte_crypto_op **ops,
> ses->pdcp.hfn_ovd_offset)),
> ses->pdcp.hfn_ovd);
> }
> -
> +#endif
> }
> send_pkts:
> loop = 0;
> @@ -2483,6 +2490,7 @@ dpaa_sec_sym_session_clear(struct rte_cryptodev *dev,
> }
> }
>
> +#ifdef RTE_LIBRTE_SECURITY
> static int
> dpaa_sec_set_ipsec_session(__rte_unused struct rte_cryptodev *dev,
> struct rte_security_session_conf *conf,
> @@ -2906,7 +2914,7 @@ dpaa_sec_security_session_destroy(void *dev __rte_unused,
> }
> return 0;
> }
> -
> +#endif
> static int
> dpaa_sec_dev_configure(struct rte_cryptodev *dev __rte_unused,
> struct rte_cryptodev_config *config __rte_unused)
> @@ -3152,6 +3160,7 @@ static struct rte_cryptodev_ops crypto_ops = {
> .sym_session_clear = dpaa_sec_sym_session_clear
> };
>
> +#ifdef RTE_LIBRTE_SECURITY
> static const struct rte_security_capability *
> dpaa_sec_capabilities_get(void *device __rte_unused)
> {
> @@ -3166,7 +3175,7 @@ static const struct rte_security_ops dpaa_sec_security_ops = {
> .set_pkt_metadata = NULL,
> .capabilities_get = dpaa_sec_capabilities_get
> };
> -
> +#endif
> static int
> dpaa_sec_uninit(struct rte_cryptodev *dev)
> {
> @@ -3190,7 +3199,9 @@ static int
> dpaa_sec_dev_init(struct rte_cryptodev *cryptodev)
> {
> struct dpaa_sec_dev_private *internals;
> +#ifdef RTE_LIBRTE_SECURITY
> struct rte_security_ctx *security_instance;
> +#endif
> struct dpaa_sec_qp *qp;
> uint32_t i, flags;
> int ret;
> @@ -3225,7 +3236,7 @@ dpaa_sec_dev_init(struct rte_cryptodev *cryptodev)
> DPAA_SEC_WARN("Device already init by primary process");
> return 0;
> }
> -
> +#ifdef RTE_LIBRTE_SECURITY
> /* Initialize security_ctx only for primary process*/
> security_instance = rte_malloc("rte_security_instances_ops",
> sizeof(struct rte_security_ctx), 0);
> @@ -3235,7 +3246,7 @@ dpaa_sec_dev_init(struct rte_cryptodev *cryptodev)
> security_instance->ops = &dpaa_sec_security_ops;
> security_instance->sess_cnt = 0;
> cryptodev->security_ctx = security_instance;
> -
> +#endif
> rte_spinlock_init(&internals->lock);
> for (i = 0; i < internals->max_nb_queue_pairs; i++) {
> /* init qman fq for queue pair */
> diff --git a/drivers/crypto/dpaa_sec/dpaa_sec.h b/drivers/crypto/dpaa_sec/dpaa_sec.h
> index a661d5a56..85aa6f6a0 100644
> --- a/drivers/crypto/dpaa_sec/dpaa_sec.h
> +++ b/drivers/crypto/dpaa_sec/dpaa_sec.h
> @@ -98,7 +98,7 @@ struct sec_cdb {
>
> uint32_t sh_desc[DPAA_SEC_MAX_DESC_SIZE];
> };
> -
> +#ifdef RTE_LIBRTE_SECURITY
> /*!
> * The structure is to be filled by user as a part of
> * dpaa_sec_proto_ctxt for PDCP Protocol
> @@ -115,14 +115,16 @@ struct sec_pdcp_ctxt {
> uint32_t hfn; /*!< Hyper Frame Number */
> uint32_t hfn_threshold; /*!< HFN Threashold for key renegotiation */
> };
> -
> +#endif
> typedef struct dpaa_sec_session_entry {
> uint8_t dir; /*!< Operation Direction */
> uint8_t ctxt; /*!< Session Context Type */
> enum rte_crypto_cipher_algorithm cipher_alg; /*!< Cipher Algorithm*/
> enum rte_crypto_auth_algorithm auth_alg; /*!< Authentication Algorithm*/
> enum rte_crypto_aead_algorithm aead_alg; /*!< AEAD Algorithm*/
> +#ifdef RTE_LIBRTE_SECURITY
> enum rte_security_session_protocol proto_alg; /*!< Security Algorithm*/
> +#endif
> union {
> struct {
> uint8_t *data; /**< pointer to key data */
> @@ -163,7 +165,9 @@ typedef struct dpaa_sec_session_entry {
> uint8_t auth_cipher_text;
> /**< Authenticate/cipher ordering */
> };
> +#ifdef RTE_LIBRTE_SECURITY
> struct sec_pdcp_ctxt pdcp;
> +#endif
> };
> struct dpaa_sec_qp *qp[MAX_DPAA_CORES];
> struct qman_fq *inq[MAX_DPAA_CORES];
> @@ -679,6 +683,7 @@ static const struct rte_cryptodev_capabilities dpaa_pdcp_capabilities[] = {
> RTE_CRYPTODEV_END_OF_CAPABILITIES_LIST()
> };
>
> +#ifdef RTE_LIBRTE_SECURITY
> static const struct rte_security_capability dpaa_sec_security_cap[] = {
> { /* IPsec Lookaside Protocol offload ESP Transport Egress */
> .action = RTE_SECURITY_ACTION_TYPE_LOOKASIDE_PROTOCOL,
> @@ -722,6 +727,7 @@ static const struct rte_security_capability dpaa_sec_security_cap[] = {
> .action = RTE_SECURITY_ACTION_TYPE_NONE
> }
> };
> +#endif
>
> /**
> * Checksum
> diff --git a/mk/rte.app.mk b/mk/rte.app.mk
> index e79f16e28..063c4605b 100644
> --- a/mk/rte.app.mk
> +++ b/mk/rte.app.mk
> @@ -275,14 +275,14 @@ _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_NITROX) += -lrte_pmd_nitrox
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_OCTEONTX_CRYPTO) += -lrte_pmd_octeontx_crypto
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_OCTEONTX2_CRYPTO) += -lrte_pmd_octeontx2_crypto
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_CRYPTO_SCHEDULER) += -lrte_pmd_crypto_scheduler
> -ifeq ($(CONFIG_RTE_LIBRTE_SECURITY),y)
> ifeq ($(CONFIG_RTE_EAL_VFIO)$(CONFIG_RTE_LIBRTE_FSLMC_BUS),yy)
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_DPAA2_SEC) += -lrte_pmd_dpaa2_sec
> endif # CONFIG_RTE_LIBRTE_FSLMC_BUS
> ifeq ($(CONFIG_RTE_LIBRTE_DPAA_BUS),y)
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_DPAA_SEC) += -lrte_pmd_dpaa_sec
> -_LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_CAAM_JR) += -lrte_pmd_caam_jr
> endif # CONFIG_RTE_LIBRTE_DPAA_BUS
> +ifeq ($(CONFIG_RTE_LIBRTE_SECURITY),y)
> +_LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_CAAM_JR) += -lrte_pmd_caam_jr
> endif # CONFIG_RTE_LIBRTE_SECURITY
> _LDLIBS-$(CONFIG_RTE_LIBRTE_PMD_VIRTIO_CRYPTO) += -lrte_pmd_virtio_crypto
> endif # CONFIG_RTE_LIBRTE_CRYPTODEV
>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
--
Thierry Herbelot
6WIND
Senior Software Engineer
next prev parent reply other threads:[~2019-10-18 8:11 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-18 7:56 [dpdk-dev] [PATCH] test/crypto: fix compilation issue without security Hemant Agrawal
2019-10-18 7:56 ` [dpdk-dev] [PATCH] app/proc-info: fix compilation with no security Hemant Agrawal
2019-10-18 8:09 ` Thierry Herbelot
2019-10-23 14:46 ` Akhil Goyal
2019-10-23 14:48 ` Akhil Goyal
2019-10-18 7:56 ` [dpdk-dev] [PATCH] crypto/dpaa_sec: enable compilation without security Hemant Agrawal
2019-10-18 8:11 ` Thierry Herbelot [this message]
2019-10-23 14:45 ` Akhil Goyal
2019-10-18 8:07 ` [dpdk-dev] [PATCH] test/crypto: fix compilation issue " Thierry Herbelot
2019-10-23 14:48 ` Akhil Goyal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=fb3f2bf2-5caa-448d-7fbd-240932ed52ef@6wind.com \
--to=thierry.herbelot@6wind.com \
--cc=akhil.goyal@nxp.com \
--cc=dev@dpdk.org \
--cc=hemant.agrawal@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.