Re: [PATCH 1/6] ASoC: Intel: cht_bsw_rt5672: Change bus format to I2S 2 channel

[Hans de Goede <hdegoede@redhat.com>]

Hi All,

Oops, I remembered a few seconds into git send-email(ing) these, that Mark
asked me to add a cover-letter to my series last time. So I've control-C-ed
that git send-email and I will resend right away with a cover-letter added.

Regards,

Hans

On 6/28/20 5:39 PM, Hans de Goede wrote:
> The default mode for SSP configuration is TDM 4 slot and so far we were
> using this for the bus format on cht-bsw-rt56732 boards.
> 
> One board, the Lenovo Miix 2 10 uses not 1 but 2 codecs connected to SSP2.
> The second piggy-backed, output-only codec is inside the keyboard-dock
> (which has extra speakers). Unlike the main rt5672 codec, we cannot
> configure this codec, it is hard coded to use 2 channel 24 bit I2S.
> 
> Using 4 channel TDM leads to the dock speakers codec (which listens in on
> the data send from the SSP to the rt5672 codec) emiting horribly distorted
> sound.
> 
> Since we only support 2 channels anyways, there is no need for TDM on any
> cht-bsw-rt5672 designs. So we can simply use I2S 2ch everywhere.
> 
> This commit fixes the Lenovo Miix 2 10 dock speakers issue by changing
> the bus format set in cht_codec_fixup() to I2S 2 channel.
> 
> This change has been tested on the following devices with a rt5672 codec:
> 
> Lenovo Miix 2 10
> Lenovo Thinkpad 8
> Lenovo Thinkpad 10 (gen 1)
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>   sound/soc/intel/boards/cht_bsw_rt5672.c | 23 +++++++++++------------
>   1 file changed, 11 insertions(+), 12 deletions(-)
> 
> diff --git a/sound/soc/intel/boards/cht_bsw_rt5672.c b/sound/soc/intel/boards/cht_bsw_rt5672.c
> index 7a43c70a1378..22e432768edb 100644
> --- a/sound/soc/intel/boards/cht_bsw_rt5672.c
> +++ b/sound/soc/intel/boards/cht_bsw_rt5672.c
> @@ -253,21 +253,20 @@ static int cht_codec_fixup(struct snd_soc_pcm_runtime *rtd,
>   	params_set_format(params, SNDRV_PCM_FORMAT_S24_LE);
>   
>   	/*
> -	 * Default mode for SSP configuration is TDM 4 slot
> +	 * Default mode for SSP configuration is TDM 4 slot. One board/design,
> +	 * the Lenovo Miix 2 10 uses not 1 but 2 codecs connected to SSP2. The
> +	 * second piggy-backed, output-only codec is inside the keyboard-dock
> +	 * (which has extra speakers). Unlike the main rt5672 codec, we cannot
> +	 * configure this codec, it is hard coded to use 2 channel 24 bit I2S.
> +	 * Since we only support 2 channels anyways, there is no need for TDM
> +	 * on any cht-bsw-rt5672 designs. So we simply use I2S 2ch everywhere.
>   	 */
> -	ret = snd_soc_dai_set_fmt(asoc_rtd_to_codec(rtd, 0),
> -				  SND_SOC_DAIFMT_DSP_B |
> -				  SND_SOC_DAIFMT_IB_NF |
> +	ret = snd_soc_dai_set_fmt(asoc_rtd_to_cpu(rtd, 0),
> +				  SND_SOC_DAIFMT_I2S     |
> +				  SND_SOC_DAIFMT_NB_NF   |
>   				  SND_SOC_DAIFMT_CBS_CFS);
>   	if (ret < 0) {
> -		dev_err(rtd->dev, "can't set format to TDM %d\n", ret);
> -		return ret;
> -	}
> -
> -	/* TDM 4 slots 24 bit, set Rx & Tx bitmask to 4 active slots */
> -	ret = snd_soc_dai_set_tdm_slot(asoc_rtd_to_codec(rtd, 0), 0xF, 0xF, 4, 24);
> -	if (ret < 0) {
> -		dev_err(rtd->dev, "can't set codec TDM slot %d\n", ret);
> +		dev_err(rtd->dev, "can't set format to I2S, err %d\n", ret);
>   		return ret;
>   	}
>   
>