On Mon, May 11, 2020 at 04:50:14PM -0500, Rob Herring wrote:
> On Fri, Apr 24, 2020 at 05:35:11PM +0200, Maxime Ripard wrote:
> > The HDMI controllers found in the BCM2711 SoC need some adjustments to the
> > bindings, especially since the registers have been shuffled around in more
> > register ranges.
> > 
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: devicetree@vger.kernel.org
> > Signed-off-by: Maxime Ripard <maxime@cerno.tech>
> > ---
> >  Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> >  1 file changed, 109 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> > new file mode 100644
> > index 000000000000..6091fe3d315b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
> > @@ -0,0 +1,109 @@
> > +# SPDX-License-Identifier: GPL-2.0
> 
> Dual license
> 
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/brcm,bcm2711-hdmi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
> > +
> > +maintainers:
> > +  - Eric Anholt <eric@anholt.net>
> > +
> > +properties:
> > +  compatible:
> > +    enum:
> > +      - brcm,bcm2711-hdmi0
> > +      - brcm,bcm2711-hdmi1
> > +
> > +  reg:
> > +    items:
> > +      - description: HDMI controller register range
> > +      - description: DVP register range
> > +      - description: HDMI PHY register range
> > +      - description: Rate Manager register range
> > +      - description: Packet RAM register range
> > +      - description: Metadata RAM register range
> > +      - description: CSC register range
> > +      - description: CEC register range
> > +      - description: HD register range
> > +
> > +  reg-names:
> > +    items:
> > +      - const: hdmi
> > +      - const: dvp
> > +      - const: phy
> > +      - const: rm
> > +      - const: packet
> > +      - const: metadata
> > +      - const: csc
> > +      - const: cec
> > +      - const: hd
> > +
> > +  clocks:
> > +    description: The HDMI state machine clock
> > +
> > +  clock-names:
> > +    const: hdmi
> > +
> > +  ddc:
> > +    allOf:
> > +      - $ref: /schemas/types.yaml#/definitions/phandle
> > +    description: >
> > +      Phandle of the I2C controller used for DDC EDID probing
> 
> This belongs in a connector node. (ddc-i2c-bus)
> 
> > +
> > +  hpd-gpios:
> > +    description: >
> > +      The GPIO pin for the HDMI hotplug detect (if it doesn't appear
> > +      as an interrupt/status bit in the HDMI controller itself)
> 
> This belongs in a connector node.

If we were to create a new binding, sure, but we're merely reusing the old
binding that is already there. The only reason it's in a separate file is
because you said it would be clearer in a separate file.

Maxime