From: Sergio Paracuellos <sergio.paracuellos@gmail.com>
To: gregkh@linuxfoundation.org
Cc: ryder.lee@mediatek.com, driverdev-devel@linuxdriverproject.org,
weijie.gao@mediatek.com, gerg@kernel.org, neil@brown.name
Subject: [PATCH v4 4/6] staging: mt7621-pci: bindings: update doc accordly to last changes
Date: Fri, 13 Mar 2020 21:09:11 +0100 [thread overview]
Message-ID: <20200313200913.24321-5-sergio.paracuellos@gmail.com> (raw)
In-Reply-To: <20200313200913.24321-1-sergio.paracuellos@gmail.com>
Properly update bindings documentation with added 'reset-gpios'
property. Delete also 'perst-gpio' which is not being used anymore.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
---
drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt b/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
index 604ec813bd45..327a68267309 100644
--- a/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
+++ b/drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
@@ -6,7 +6,6 @@ Required properties:
- reg: Base addresses and lengths of the PCIe subsys and root ports.
- bus-range: Range of bus numbers associated with this controller.
- #address-cells: Address representation for root ports (must be 3)
-- perst-gpio: PCIe reset signal line.
- pinctrl-names : The pin control state names.
- pinctrl-0: The "default" pinctrl state.
- #size-cells: Size representation for root ports (must be 2)
@@ -24,6 +23,7 @@ Required properties:
See ../clocks/clock-bindings.txt for details.
- clock-names: Must be "pcie0", "pcie1", "pcieN"... based on the number of
root ports.
+- reset-gpios: GPIO specs for the reset pins.
In addition, the device tree node must have sub-nodes describing each PCIe port
interface, having the following mandatory properties:
@@ -49,7 +49,6 @@ Example for MT7621:
#address-cells = <3>;
#size-cells = <2>;
- perst-gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_pins>;
@@ -74,6 +73,10 @@ Example for MT7621:
clocks = <&clkctrl 24 &clkctrl 25 &clkctrl 26>;
clock-names = "pcie0", "pcie1", "pcie2";
+ reset-gpios = <&gpio 19 GPIO_ACTIVE_LOW>,
+ <&gpio 8 GPIO_ACTIVE_LOW>,
+ <&gpio 7 GPIO_ACTIVE_LOW>;
+
pcie@0,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <3>;
--
2.25.1
_______________________________________________
devel mailing list
devel@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
next prev parent reply other threads:[~2020-03-13 20:09 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-13 20:09 [PATCH v4 0/6] staging: mt7621-pci: re-do reset boot process Sergio Paracuellos
2020-03-13 20:09 ` [PATCH v4 1/6] staging: mt7621-pci: use gpios for properly reset Sergio Paracuellos
2020-03-13 20:09 ` [PATCH v4 2/6] staging: mt7621-pci: change value for 'PERST_DELAY_MS' Sergio Paracuellos
2020-03-13 20:09 ` [PATCH v4 3/6] staging: mt7621-dts: make use of 'reset-gpios' property for pci Sergio Paracuellos
2020-03-13 20:09 ` Sergio Paracuellos [this message]
2020-03-13 20:09 ` [PATCH v4 5/6] staging: mt7621-pci: release gpios after pci initialization Sergio Paracuellos
2020-03-20 14:59 ` Chuanhong Guo
2020-03-20 15:28 ` Sergio Paracuellos
2020-03-20 15:39 ` Chuanhong Guo
2020-03-20 16:32 ` Sergio Paracuellos
2020-03-20 16:34 ` Sergio Paracuellos
2020-03-21 6:36 ` Chuanhong Guo
2020-03-21 7:28 ` Sergio Paracuellos
2020-03-13 20:09 ` [PATCH v4 6/6] staging: mt7621-pci: delete no more needed 'mt7621_reset_port' Sergio Paracuellos
2020-03-14 10:42 ` [PATCH v4 0/6] staging: mt7621-pci: re-do reset boot process Sergio Paracuellos
2020-03-15 12:35 ` Sergio Paracuellos
2020-03-19 12:42 ` Greg Ungerer
2020-03-19 13:43 ` Sergio Paracuellos
2020-03-19 13:47 ` Sergio Paracuellos
2020-03-19 14:28 ` Greg Ungerer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200313200913.24321-5-sergio.paracuellos@gmail.com \
--to=sergio.paracuellos@gmail.com \
--cc=driverdev-devel@linuxdriverproject.org \
--cc=gerg@kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=neil@brown.name \
--cc=ryder.lee@mediatek.com \
--cc=weijie.gao@mediatek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).