From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: balbi@kernel.org, gregkh@linuxfoundation.org,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
kishon@ti.com, hminas@synopsys.com,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue
Date: Wed, 20 Mar 2019 09:43:01 +0800 [thread overview]
Message-ID: <1553046181.10179.160.camel@mhfsdcap03> (raw)
In-Reply-To: <703e82ad-5e1e-a03d-796c-dc1ddde7d2dc@baylibre.com>
Hi,
On Tue, 2019-03-19 at 09:15 +0100, Neil Armstrong wrote:
> Hi,
>
> On 19/03/2019 02:57, Chunfeng Yun wrote:
> > Hi Neil,
> > On Mon, 2019-03-18 at 11:11 +0100, Neil Armstrong wrote:
> >> Adds support for Amlogic G12A USB Control Glue HW.
> >>
> >> The Amlogic G12A SoC Family embeds 2 USB Controllers :
> >> - a DWC3 IP configured as Host for USB2 and USB3
> >> - a DWC2 IP configured as Peripheral USB2 Only
> >>
> >> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
> >> to an USB3+PCIE Combo PHY shared with the PCIE controller.
> >>
> >> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
> >> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
> >> setups the on-chip OTG mode selection for this PHY.
> >>
> >> This drivers supports the on-probe setup of the OTG mode, and manually
> >> via a debugfs interface. The IRQ mode change detect is yet to be added
> >> in a future patchset, mainly due to lack of hardware to validate on.
> >>
> >> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> >> ---
> >> drivers/usb/dwc3/Kconfig | 10 +
> >> drivers/usb/dwc3/Makefile | 1 +
> >> drivers/usb/dwc3/dwc3-meson-g12a.c | 602 +++++++++++++++++++++++++++++
> >> 3 files changed, 613 insertions(+)
> >> create mode 100644 drivers/usb/dwc3/dwc3-meson-g12a.c
> >>
> >> diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> >> index 2b1494460d0c..d2ea9670563c 100644
> >> --- a/drivers/usb/dwc3/Kconfig
> >> +++ b/drivers/usb/dwc3/Kconfig
> >> @@ -95,6 +95,16 @@ config USB_DWC3_KEYSTONE
> >> Support of USB2/3 functionality in TI Keystone2 and AM654 platforms.
> >> Say 'Y' or 'M' here if you have one such device
> >>
> >> +config USB_DWC3_MESON_G12A
> >> + tristate "Amlogic Meson G12A Platforms"
> >> + depends on OF && COMMON_CLK
> >> + depends on ARCH_MESON || COMPILE_TEST
> >> + default USB_DWC3
> >> + select USB_ROLE_SWITCH
> >> + help
> >> + Support USB2/3 functionality in Amlogic G12A platforms.
> >> + Say 'Y' or 'M' if you have one such device.
> >> +
> >> config USB_DWC3_OF_SIMPLE
> >> tristate "Generic OF Simple Glue Layer"
> >> depends on OF && COMMON_CLK
> >> diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> >> index 6e3ef6144e5d..ae86da0dc5bd 100644
> >> --- a/drivers/usb/dwc3/Makefile
> >> +++ b/drivers/usb/dwc3/Makefile
> >> @@ -47,6 +47,7 @@ obj-$(CONFIG_USB_DWC3_EXYNOS) += dwc3-exynos.o
> >> obj-$(CONFIG_USB_DWC3_PCI) += dwc3-pci.o
> >> obj-$(CONFIG_USB_DWC3_HAPS) += dwc3-haps.o
> >> obj-$(CONFIG_USB_DWC3_KEYSTONE) += dwc3-keystone.o
> >> +obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
> >> obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
> >> obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
> >> obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
> >> diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c b/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> new file mode 100644
> >> index 000000000000..9f4554e8e6e7
> >> --- /dev/null
> >> +++ b/drivers/usb/dwc3/dwc3-meson-g12a.c
> >> @@ -0,0 +1,602 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * USB Glue for Amlogic G12A SoCs
> >> + *
> >> + * Copyright (c) 2019 BayLibre, SAS
> >> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> >> + */
> >> +
> >> +/*
> >> + * The USB is organized with a glue around the DWC3 Controller IP as :
> >> + * - Control registers for each USB2 Ports
> >> + * - Control registers for the USB PHY layer
> >> + * - SuperSpeed PHY can be enabled only if port is used
> >> + *
> >> + * TOFIX:
> >> + * - Add dynamic OTG switching with ID change interrupt
> >> + */
> >> +
>
> [..]
>
> >> +
> >> + ret = of_platform_populate(np, NULL, NULL, dev);
> >> + if (ret) {
> >> + clk_disable_unprepare(priv->clk);
> >> + clk_put(priv->clk);
> > No need clk_put()
>
> Exact
>
> >> +
> >> + goto err_phys_exit;
> >> + }
> >> +
> >> + /* Setup OTG mode corresponding to the ID pin */
> >> + if (priv->otg_mode == USB_DR_MODE_OTG) {
> >> + /* TOFIX Handle ID mode toggling via IRQ */
> >> + otg_id = dwc3_meson_g12a_get_id(priv);
> >> + if (otg_id != priv->otg_phy_mode) {
> >> + if (dwc3_meson_g12a_otg_mode_set(priv, otg_id))
> >> + dev_warn(dev, "Failed to switch OTG mode\n");
> >> + }
> >> + }
> >> +
> >> + /* Setup role switcher */
> >> + priv->switch_desc.usb2_port = dwc3_meson_g12_find_child(dev,
> >> + "snps,dwc3");
> >> + priv->switch_desc.udc = dwc3_meson_g12_find_child(dev, "snps,dwc2");
> >> + priv->switch_desc.allow_userspace_control = true;
> >> + priv->switch_desc.set = dwc3_meson_g12a_role_set;
> >> + priv->switch_desc.get = dwc3_meson_g12a_role_get;
> >> +
> >> + priv->role_switch = usb_role_switch_register(dev, &priv->switch_desc);
> >> + if (IS_ERR(priv->role_switch))
> >> + dev_warn(dev, "Unable to register Role Switch\n");
> >> +
> >> + pm_runtime_set_active(dev);
> >> + pm_runtime_enable(dev);
> >> + pm_runtime_get_sync(dev);
> >> +
> >> + return 0;
> >> +
> >> +err_phys_exit:
> >> + for (i = 0 ; i < PHY_COUNT ; ++i)
> >> + phy_exit(priv->phys[i]);
> >> +
> >> +err_phys_power:
> >> + for (i = 0 ; i < PHY_COUNT ; ++i)
> >> + phy_power_off(priv->phys[i]);
> >> +
> >> +err_phys_put:
> >> + for (i = 0 ; i < PHY_COUNT ; ++i)
> >> + phy_put(priv->phys[i]);
> > you get phy by devm_phy_optional_get(), no need call phy_put(),
>
> Indeed, also forgot these
>
> >> +
> >> + return ret;
> >> +}
> >> +
> >> +static int dwc3_meson_g12a_remove(struct platform_device *pdev)
> >> +{
> >> + struct dwc3_meson_g12a *priv = platform_get_drvdata(pdev);
> >> + struct device *dev = &pdev->dev;
> >> + int i;
> >> +
> >> + usb_role_switch_unregister(priv->role_switch);
> >> +
> >> + of_platform_depopulate(dev);
> >> +
> >> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> >> + phy_power_off(priv->phys[i]);
> >> + phy_exit(priv->phys[i]);
> >> + phy_put(priv->phys[i]);
> > here, and remove others if have.
>
> This is the last one I hope
>
> >> + }
> >> +
> >> + pm_runtime_disable(dev);
> >> + pm_runtime_put_noidle(dev);
> >> + pm_runtime_set_suspended(dev);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int __maybe_unused dwc3_meson_g12a_runtime_suspend(struct device *dev)
> >> +{
> >> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> >> +
> >> + clk_disable(priv->clk);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int __maybe_unused dwc3_meson_g12a_runtime_resume(struct device *dev)
> >> +{
> >> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> >> +
> >> + return clk_enable(priv->clk);
> >> +}
> >> +
> >> +static int __maybe_unused dwc3_meson_g12a_suspend(struct device *dev)
> >> +{
> >> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> >> + int i;
> >> +
> >> + for (i = 0 ; i < PHY_COUNT ; ++i)
> >> + phy_exit(priv->phys[i]);
> >> +
> >> + reset_control_assert(priv->reset);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static int __maybe_unused dwc3_meson_g12a_resume(struct device *dev)
> >> +{
> >> + struct dwc3_meson_g12a *priv = dev_get_drvdata(dev);
> >> + int i, ret;
> >> +
> >> + reset_control_deassert(priv->reset);
> >> +
> >> + dwc3_meson_g12a_usb_init(priv);
> >> +
> >> + /* Init PHYs */
> >> + for (i = 0 ; i < PHY_COUNT ; ++i) {
> >> + ret = phy_init(priv->phys[i]);
> >> + if (ret)
> >> + return ret;
> >> + }
> > Do you need power on phys?
>
> Regulators can be tied to the PHYs, should I disable power on suspend aswell ?
I find that the phy driver you used doesn't provide .power_on/off, so
the current flow won't cause something wrong, but if the phy driver
provides .power_on/off, it will do.
>
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +static const struct dev_pm_ops dwc3_meson_g12a_dev_pm_ops = {
> >> + SET_SYSTEM_SLEEP_PM_OPS(dwc3_meson_g12a_suspend, dwc3_meson_g12a_resume)
> >> + SET_RUNTIME_PM_OPS(dwc3_meson_g12a_runtime_suspend,
> >> + dwc3_meson_g12a_runtime_resume, NULL)
> >> +};
> >> +
> >> +static const struct of_device_id dwc3_meson_g12a_match[] = {
> >> + { .compatible = "amlogic,meson-g12a-usb-ctrl" },
> >> + { /* Sentinel */ }
> >> +};
> >> +MODULE_DEVICE_TABLE(of, dwc3_meson_g12a_match);
> >> +
> >> +static struct platform_driver dwc3_meson_g12a_driver = {
> >> + .probe = dwc3_meson_g12a_probe,
> >> + .remove = dwc3_meson_g12a_remove,
> >> + .driver = {
> >> + .name = "dwc3-meson-g12a",
> >> + .of_match_table = dwc3_meson_g12a_match,
> >> + .pm = &dwc3_meson_g12a_dev_pm_ops,
> >> + },
> >> +};
> >> +
> >> +module_platform_driver(dwc3_meson_g12a_driver);
> >> +MODULE_LICENSE("GPL v2");
> >> +MODULE_DESCRIPTION("Amlogic Meson G12A USB Glue Layer");
> >> +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
> >
> >
>
> Thanks,
> Neil
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-03-20 1:43 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-18 10:11 [PATCH v3 0/8] arm64: meson: Add support for USB on Amlogic G12A Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 1/8] dt-bindings: phy: Add Amlogic G12A USB2 PHY Bindings Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 2/8] dt-bindings: phy: Add Amlogic G12A USB3+PCIE Combo " Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 3/8] dt-bindings: usb: dwc2: Add Amlogic G12A DWC2 Compatible Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 4/8] dt-bindings: usb: dwc3: Add Amlogic G12A DWC3 Glue Bindings Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 5/8] phy: amlogic: add Amlogic G12A USB2 PHY Driver Neil Armstrong
2019-03-18 10:18 ` Kishon Vijay Abraham I
2019-03-18 11:28 ` Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 6/8] phy: amlogic: Add Amlogic G12A USB3 + PCIE Combo " Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 7/8] usb: dwc2: Add Amlogic G12A DWC2 Params Neil Armstrong
2019-03-18 10:11 ` [PATCH v3 8/8] usb: dwc3: Add Amlogic G12A DWC3 glue Neil Armstrong
2019-03-19 1:57 ` Chunfeng Yun
2019-03-19 8:15 ` Neil Armstrong
2019-03-20 1:43 ` Chunfeng Yun [this message]
2019-03-18 13:27 ` [PATCH v3 0/8] arm64: meson: Add support for USB on Amlogic G12A Neil Armstrong
2019-03-18 19:41 ` Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1553046181.10179.160.camel@mhfsdcap03 \
--to=chunfeng.yun@mediatek.com \
--cc=balbi@kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=hminas@synopsys.com \
--cc=kishon@ti.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=narmstrong@baylibre.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).