linux-amlogic.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Guillaume La Roque <glaroque@baylibre.com>
To: amit.kucheria@linaro.org, rui.zhang@intel.com,
	edubezval@gmail.com, daniel.lezcano@linaro.org
Cc: devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org,
	linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org, linux-pm@vger.kernel.org
Subject: [PATCH v6 2/7] thermal: amlogic: Add thermal driver to support G12 SoCs
Date: Fri, 27 Sep 2019 20:43:47 +0200	[thread overview]
Message-ID: <20190927184352.28759-3-glaroque@baylibre.com> (raw)
In-Reply-To: <20190927184352.28759-1-glaroque@baylibre.com>

Amlogic G12A and G12B SoCs integrate two thermal sensors
with the same design. One is located close to the DDR controller
and the other one is located close to the PLLs (between the CPU and GPU).

The calibration data for each of the thermal sensors instance is stored
in a different location within the AO region.

Implement reading the temperature from each thermal sensor.

The IP block has more functionality, which may be added to this driver
in the future:
- chip reset when the temperature exceeds a configurable threshold
- up to four interrupts when the temperature has risen above a
configurable threshold
- up to four interrupts when the temperature has fallen below a
configurable threshold

Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
---
 drivers/thermal/Kconfig           |  11 +
 drivers/thermal/Makefile          |   1 +
 drivers/thermal/amlogic_thermal.c | 333 ++++++++++++++++++++++++++++++
 3 files changed, 345 insertions(+)
 create mode 100644 drivers/thermal/amlogic_thermal.c

diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 9966364a6deb..0f31bb4bc372 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -348,6 +348,17 @@ config MTK_THERMAL
 	  Enable this option if you want to have support for thermal management
 	  controller present in Mediatek SoCs
 
+config AMLOGIC_THERMAL
+	tristate "Amlogic Thermal Support"
+	default ARCH_MESON
+	depends on OF && ARCH_MESON
+	help
+	  If you say yes here you get support for Amlogic Thermal
+	  for G12 SoC Family.
+
+	  This driver can also be built as a module. If so, the module will
+	  be called amlogic_thermal.
+
 menu "Intel thermal drivers"
 depends on X86 || X86_INTEL_QUARK || COMPILE_TEST
 source "drivers/thermal/intel/Kconfig"
diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
index 74a37c7f847a..baeb70bf0568 100644
--- a/drivers/thermal/Makefile
+++ b/drivers/thermal/Makefile
@@ -54,3 +54,4 @@ obj-$(CONFIG_MTK_THERMAL)	+= mtk_thermal.o
 obj-$(CONFIG_GENERIC_ADC_THERMAL)	+= thermal-generic-adc.o
 obj-$(CONFIG_ZX2967_THERMAL)	+= zx2967_thermal.o
 obj-$(CONFIG_UNIPHIER_THERMAL)	+= uniphier_thermal.o
+obj-$(CONFIG_AMLOGIC_THERMAL)     += amlogic_thermal.o
diff --git a/drivers/thermal/amlogic_thermal.c b/drivers/thermal/amlogic_thermal.c
new file mode 100644
index 000000000000..8a9e9bc421c6
--- /dev/null
+++ b/drivers/thermal/amlogic_thermal.c
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Amlogic Thermal Sensor Driver
+ *
+ * Copyright (C) 2017 Huan Biao <huan.biao@amlogic.com>
+ * Copyright (C) 2019 Guillaume La Roque <glaroque@baylibre.com>
+ *
+ * Register value to celsius temperature formulas:
+ *	Read_Val	    m * U
+ * U = ---------, Uptat = ---------
+ *	2^16		  1 + n * U
+ *
+ * Temperature = A * ( Uptat + u_efuse / 2^16 )- B
+ *
+ *  A B m n : calibration parameters
+ *  u_efuse : fused calibration value, it's a signed 16 bits value
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#include "thermal_core.h"
+
+#define TSENSOR_CFG_REG1			0x4
+	#define TSENSOR_CFG_REG1_RSET_VBG	BIT(12)
+	#define TSENSOR_CFG_REG1_RSET_ADC	BIT(11)
+	#define TSENSOR_CFG_REG1_VCM_EN		BIT(10)
+	#define TSENSOR_CFG_REG1_VBG_EN		BIT(9)
+	#define TSENSOR_CFG_REG1_OUT_CTL	BIT(6)
+	#define TSENSOR_CFG_REG1_FILTER_EN	BIT(5)
+	#define TSENSOR_CFG_REG1_DEM_EN		BIT(3)
+	#define TSENSOR_CFG_REG1_CH_SEL		GENMASK(1, 0)
+	#define TSENSOR_CFG_REG1_ENABLE		\
+		(TSENSOR_CFG_REG1_FILTER_EN |	\
+		 TSENSOR_CFG_REG1_VCM_EN |	\
+		 TSENSOR_CFG_REG1_VBG_EN |	\
+		 TSENSOR_CFG_REG1_DEM_EN |	\
+		 TSENSOR_CFG_REG1_CH_SEL)
+
+#define TSENSOR_STAT0			0x40
+
+#define TSENSOR_STAT9			0x64
+
+#define TSENSOR_READ_TEMP_MASK		GENMASK(15, 0)
+#define TSENSOR_TEMP_MASK		GENMASK(11, 0)
+
+#define TSENSOR_TRIM_SIGN_MASK		BIT(15)
+#define TSENSOR_TRIM_TEMP_MASK		GENMASK(14, 0)
+#define TSENSOR_TRIM_VERSION_MASK	GENMASK(31, 24)
+
+#define TSENSOR_TRIM_VERSION(_version)	\
+	FIELD_GET(TSENSOR_TRIM_VERSION_MASK, _version)
+
+#define TSENSOR_TRIM_CALIB_VALID_MASK	(GENMASK(3, 2) | BIT(7))
+
+#define TSENSOR_CALIB_OFFSET	1
+#define TSENSOR_CALIB_SHIFT	4
+
+/**
+ * struct amlogic_thermal_soc_calib_data
+ * @A, B, m, n: calibration parameters
+ * This structure is required for configuration of amlogic thermal driver.
+ */
+struct amlogic_thermal_soc_calib_data {
+	int A;
+	int B;
+	int m;
+	int n;
+};
+
+/**
+ * struct amlogic_thermal_data
+ * @u_efuse_off: register offset to read fused calibration value
+ * @calibration_parameters: calibration parameters structure pointer
+ * @regmap_config: regmap config for the device
+ * This structure is required for configuration of amlogic thermal driver.
+ */
+struct amlogic_thermal_data {
+	int u_efuse_off;
+	const struct amlogic_thermal_soc_calib_data *calibration_parameters;
+	const struct regmap_config *regmap_config;
+};
+
+struct amlogic_thermal {
+	struct platform_device *pdev;
+	const struct amlogic_thermal_data *data;
+	struct regmap *regmap;
+	struct regmap *sec_ao_map;
+	struct clk *clk;
+	struct thermal_zone_device *tzd;
+	u32 trim_info;
+};
+
+/*
+ * Calculate a temperature value from a temperature code.
+ * The unit of the temperature is degree milliCelsius.
+ */
+static int amlogic_thermal_code_to_millicelsius(struct amlogic_thermal *pdata,
+						int temp_code)
+{
+	const struct amlogic_thermal_soc_calib_data *param =
+					pdata->data->calibration_parameters;
+	int temp;
+	s64 factor, Uptat, uefuse;
+
+	uefuse = pdata->trim_info & TSENSOR_TRIM_SIGN_MASK ?
+			     ~(pdata->trim_info & TSENSOR_TRIM_TEMP_MASK) + 1 :
+			     (pdata->trim_info & TSENSOR_TRIM_TEMP_MASK);
+
+	factor = param->n * temp_code;
+	factor = div_s64(factor, 100);
+
+	Uptat = temp_code * param->m;
+	Uptat = div_s64(Uptat, 100);
+	Uptat = Uptat * BIT(16);
+	Uptat = div_s64(Uptat, BIT(16) + factor);
+
+	temp = (Uptat + uefuse) * param->A;
+	temp = div_s64(temp, BIT(16));
+	temp = (temp - param->B) * 100;
+
+	return temp;
+}
+
+static int amlogic_thermal_initialize(struct amlogic_thermal *pdata)
+{
+	int ret = 0;
+	int ver;
+
+	regmap_read(pdata->sec_ao_map, pdata->data->u_efuse_off,
+		    &pdata->trim_info);
+
+	ver = TSENSOR_TRIM_VERSION(pdata->trim_info);
+
+	if ((ver & TSENSOR_TRIM_CALIB_VALID_MASK) == 0) {
+		ret = -EINVAL;
+		dev_err(&pdata->pdev->dev,
+			"tsensor thermal calibration not supported: 0x%x!\n",
+			ver);
+	}
+
+	return ret;
+}
+
+static int amlogic_thermal_enable(struct amlogic_thermal *data)
+{
+	int ret;
+
+	ret = clk_prepare_enable(data->clk);
+	if (ret)
+		return ret;
+
+	regmap_update_bits(data->regmap, TSENSOR_CFG_REG1,
+			   TSENSOR_CFG_REG1_ENABLE, TSENSOR_CFG_REG1_ENABLE);
+
+	return 0;
+}
+
+static int amlogic_thermal_disable(struct amlogic_thermal *data)
+{
+	regmap_update_bits(data->regmap, TSENSOR_CFG_REG1,
+			   TSENSOR_CFG_REG1_ENABLE, 0);
+	clk_disable_unprepare(data->clk);
+
+	return 0;
+}
+
+static int amlogic_thermal_get_temp(void *data, int *temp)
+{
+	unsigned int tval;
+	struct amlogic_thermal *pdata = data;
+
+	if (!data)
+		return -EINVAL;
+
+	regmap_read(pdata->regmap, TSENSOR_STAT0, &tval);
+	*temp =
+	   amlogic_thermal_code_to_millicelsius(pdata,
+						tval & TSENSOR_READ_TEMP_MASK);
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops amlogic_thermal_ops = {
+	.get_temp	= amlogic_thermal_get_temp,
+};
+
+static const struct regmap_config amlogic_thermal_regmap_config_g12a = {
+	.reg_bits = 8,
+	.val_bits = 32,
+	.reg_stride = 4,
+	.max_register = TSENSOR_STAT9,
+};
+
+static const struct amlogic_thermal_soc_calib_data amlogic_thermal_g12a = {
+	.A = 9411,
+	.B = 3159,
+	.m = 424,
+	.n = 324,
+};
+
+static const struct amlogic_thermal_data amlogic_thermal_g12a_cpu_param = {
+	.u_efuse_off = 0x128,
+	.calibration_parameters = &amlogic_thermal_g12a,
+	.regmap_config = &amlogic_thermal_regmap_config_g12a,
+};
+
+static const struct amlogic_thermal_data amlogic_thermal_g12a_ddr_param = {
+	.u_efuse_off = 0xf0,
+	.calibration_parameters = &amlogic_thermal_g12a,
+	.regmap_config = &amlogic_thermal_regmap_config_g12a,
+};
+
+static const struct of_device_id of_amlogic_thermal_match[] = {
+	{
+		.compatible = "amlogic,g12a-ddr-thermal",
+		.data = &amlogic_thermal_g12a_ddr_param,
+	},
+	{
+		.compatible = "amlogic,g12a-cpu-thermal",
+		.data = &amlogic_thermal_g12a_cpu_param,
+	},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, of_amlogic_thermal_match);
+
+static int amlogic_thermal_probe(struct platform_device *pdev)
+{
+	struct amlogic_thermal *pdata;
+	struct device *dev = &pdev->dev;
+	void __iomem *base;
+	int ret;
+
+	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+	if (!pdata)
+		return -ENOMEM;
+
+	pdata->data = of_device_get_match_data(dev);
+	pdata->pdev = pdev;
+	platform_set_drvdata(pdev, pdata);
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base)) {
+		dev_err(dev, "failed to get io address\n");
+		return PTR_ERR(base);
+	}
+
+	pdata->regmap = devm_regmap_init_mmio(dev, base,
+					      pdata->data->regmap_config);
+	if (IS_ERR(pdata->regmap))
+		return PTR_ERR(pdata->regmap);
+
+	pdata->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(pdata->clk)) {
+		if (PTR_ERR(pdata->clk) != -EPROBE_DEFER)
+			dev_err(dev, "failed to get clock\n");
+		return PTR_ERR(pdata->clk);
+	}
+
+	pdata->sec_ao_map = syscon_regmap_lookup_by_phandle
+		(pdev->dev.of_node, "amlogic,ao-secure");
+	if (IS_ERR(pdata->sec_ao_map)) {
+		dev_err(dev, "syscon regmap lookup failed.\n");
+		return PTR_ERR(pdata->sec_ao_map);
+	}
+
+	pdata->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev,
+							  0,
+							  pdata,
+							  &amlogic_thermal_ops);
+	if (IS_ERR(pdata->tzd)) {
+		ret = PTR_ERR(pdata->tzd);
+		dev_err(dev, "Failed to register tsensor: %d\n", ret);
+		return ret;
+	}
+
+	ret = amlogic_thermal_initialize(pdata);
+	if (ret)
+		return ret;
+
+	ret = amlogic_thermal_enable(pdata);
+
+	return ret;
+}
+
+static int amlogic_thermal_remove(struct platform_device *pdev)
+{
+	struct amlogic_thermal *data = platform_get_drvdata(pdev);
+
+	return amlogic_thermal_disable(data);
+}
+
+static int __maybe_unused amlogic_thermal_suspend(struct device *dev)
+{
+	struct amlogic_thermal *data = dev_get_drvdata(dev);
+
+	return amlogic_thermal_disable(data);
+}
+
+static int __maybe_unused amlogic_thermal_resume(struct device *dev)
+{
+	struct amlogic_thermal *data = dev_get_drvdata(dev);
+
+	return amlogic_thermal_enable(data);
+}
+
+static SIMPLE_DEV_PM_OPS(amlogic_thermal_pm_ops,
+			 amlogic_thermal_suspend, amlogic_thermal_resume);
+
+static struct platform_driver amlogic_thermal_driver = {
+	.driver = {
+		.name		= "amlogic_thermal",
+		.pm		= &amlogic_thermal_pm_ops,
+		.of_match_table = of_amlogic_thermal_match,
+	},
+	.probe	= amlogic_thermal_probe,
+	.remove	= amlogic_thermal_remove,
+};
+
+module_platform_driver(amlogic_thermal_driver);
+
+MODULE_AUTHOR("Guillaume La Roque <glaroque@baylibre.com>");
+MODULE_DESCRIPTION("Amlogic thermal driver");
+MODULE_LICENSE("GPL v2");
-- 
2.17.1


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

  parent reply	other threads:[~2019-09-27 18:45 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-09-27 18:43 [PATCH v6 0/7] Add support of New Amlogic temperature sensor for G12 SoCs Guillaume La Roque
2019-09-27 18:43 ` [PATCH v6 1/7] dt-bindings: thermal: Add DT bindings documentation for Amlogic Thermal Guillaume La Roque
2019-09-30  9:34   ` Amit Kucheria
2019-09-30  9:35   ` Amit Kucheria
2019-09-27 18:43 ` Guillaume La Roque [this message]
2019-09-30  9:37   ` [PATCH v6 2/7] thermal: amlogic: Add thermal driver to support G12 SoCs Amit Kucheria
2019-09-27 18:43 ` [PATCH v6 3/7] arm64: dts: amlogic: g12: add temperature sensor Guillaume La Roque
2019-09-30  8:19   ` Neil Armstrong
2019-09-30  9:39   ` Amit Kucheria
2019-09-27 18:43 ` [PATCH v6 4/7] arm64: dts: meson: g12: Add minimal thermal zone Guillaume La Roque
2019-09-30  8:19   ` Neil Armstrong
2019-09-30  9:44   ` Amit Kucheria
2019-09-27 18:43 ` [PATCH v6 5/7] arm64: dts: amlogic: g12a: add cooling properties Guillaume La Roque
2019-09-30  8:19   ` Neil Armstrong
2019-09-27 18:43 ` [PATCH v6 6/7] arm64: dts: amlogic: g12b: " Guillaume La Roque
2019-09-30  8:19   ` Neil Armstrong
2019-09-27 18:43 ` [PATCH v6 7/7] MAINTAINERS: add entry for Amlogic Thermal driver Guillaume La Roque

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190927184352.28759-3-glaroque@baylibre.com \
    --to=glaroque@baylibre.com \
    --cc=amit.kucheria@linaro.org \
    --cc=daniel.lezcano@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=edubezval@gmail.com \
    --cc=linux-amlogic@lists.infradead.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=rui.zhang@intel.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).