From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: devicetree@vger.kernel.org,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Kevin Hilman <khilman@baylibre.com>,
linux-kernel@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
Yue Wang <yue.wang@Amlogic.com>,
Remi Pommarel <repk@triplefau.lt>,
linux-pci@vger.kernel.org, Bjorn Helgaas <bhelgaas@google.com>,
linux-amlogic@lists.infradead.org, kishon@ti.com,
Jerome Brunet <jbrunet@baylibre.com>
Subject: Re: [PATCH v6 5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver
Date: Wed, 4 Mar 2020 10:44:34 +0000 [thread overview]
Message-ID: <20200304104434.GA6613@e121166-lin.cambridge.arm.com> (raw)
In-Reply-To: <af715acf-9ea4-8a82-92d3-578d09aec760@baylibre.com>
On Wed, Mar 04, 2020 at 10:08:55AM +0100, Neil Armstrong wrote:
> Hi Lorenzo,
>
>
> On 03/03/2020 18:19, Lorenzo Pieralisi wrote:
> > On Fri, Jan 24, 2020 at 12:29:41AM +0100, Remi Pommarel wrote:
> >> This adds support for the MIPI analog PHY which is also used for PCIE
> >> found in the Amlogic AXG SoC Family.
> >>
> >> MIPI or PCIE selection is done by the #phy-cells, making the mode
> >> static and exclusive.
> >>
> >> For now only PCIE fonctionality is supported.
> >>
> >> This PHY will be used to replace the mipi_enable clock gating logic
> >> which was mistakenly added in the clock subsystem. This also activate
> >> a non documented band gap bit in those registers that allows reliable
> >> PCIE clock signal generation on AXG platforms.
> >>
> >> Signed-off-by: Remi Pommarel <repk@triplefau.lt>
> >> ---
> >> drivers/phy/amlogic/Kconfig | 11 +
> >> drivers/phy/amlogic/Makefile | 11 +-
> >> .../amlogic/phy-meson-axg-mipi-pcie-analog.c | 188 ++++++++++++++++++
> >> 3 files changed, 205 insertions(+), 5 deletions(-)
> >> create mode 100644 drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> >
> > Kishon, Neil,
> >
> > can you please review/ack this patch and patch 6 ?
>
> Sure, it was already acked by jerome, but it's also ok for me:
>
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Thanks. Sorry for the pedantry but on patch (6) too.
Lorenzo
> Neil
> >
> > I would like to queue the series shortly, thanks.
> >
> > Lorenzo
> >
> >> diff --git a/drivers/phy/amlogic/Kconfig b/drivers/phy/amlogic/Kconfig
> >> index af774ac2b934..8c9cf2403591 100644
> >> --- a/drivers/phy/amlogic/Kconfig
> >> +++ b/drivers/phy/amlogic/Kconfig
> >> @@ -59,3 +59,14 @@ config PHY_MESON_G12A_USB3_PCIE
> >> Enable this to support the Meson USB3 + PCIE Combo PHY found
> >> in Meson G12A SoCs.
> >> If unsure, say N.
> >> +
> >> +config PHY_MESON_AXG_MIPI_PCIE_ANALOG
> >> + tristate "Meson AXG MIPI + PCIE analog PHY driver"
> >> + default ARCH_MESON
> >> + depends on OF && (ARCH_MESON || COMPILE_TEST)
> >> + select GENERIC_PHY
> >> + select REGMAP_MMIO
> >> + help
> >> + Enable this to support the Meson MIPI + PCIE analog PHY
> >> + found in Meson AXG SoCs.
> >> + If unsure, say N.
> >> diff --git a/drivers/phy/amlogic/Makefile b/drivers/phy/amlogic/Makefile
> >> index 11d1c42ac2be..0aecf92d796a 100644
> >> --- a/drivers/phy/amlogic/Makefile
> >> +++ b/drivers/phy/amlogic/Makefile
> >> @@ -1,6 +1,7 @@
> >> # SPDX-License-Identifier: GPL-2.0-only
> >> -obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
> >> -obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
> >> -obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
> >> +obj-$(CONFIG_PHY_MESON8B_USB2) += phy-meson8b-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_GXL_USB2) += phy-meson-gxl-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_G12A_USB2) += phy-meson-g12a-usb2.o
> >> +obj-$(CONFIG_PHY_MESON_GXL_USB3) += phy-meson-gxl-usb3.o
> >> +obj-$(CONFIG_PHY_MESON_G12A_USB3_PCIE) += phy-meson-g12a-usb3-pcie.o
> >> +obj-$(CONFIG_PHY_MESON_AXG_MIPI_PCIE_ANALOG) += phy-meson-axg-mipi-pcie-analog.o
> >> diff --git a/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> >> new file mode 100644
> >> index 000000000000..1431cbf885e1
> >> --- /dev/null
> >> +++ b/drivers/phy/amlogic/phy-meson-axg-mipi-pcie-analog.c
> >> @@ -0,0 +1,188 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Amlogic AXG MIPI + PCIE analog PHY driver
> >> + *
> >> + * Copyright (C) 2019 Remi Pommarel <repk@triplefau.lt>
> >> + */
> >> +#include <linux/module.h>
> >> +#include <linux/phy/phy.h>
> >> +#include <linux/regmap.h>
> >> +#include <linux/platform_device.h>
> >> +#include <dt-bindings/phy/phy.h>
> >> +
> >> +#define HHI_MIPI_CNTL0 0x00
> >> +#define HHI_MIPI_CNTL0_COMMON_BLOCK GENMASK(31, 28)
> >> +#define HHI_MIPI_CNTL0_ENABLE BIT(29)
> >> +#define HHI_MIPI_CNTL0_BANDGAP BIT(26)
> >> +#define HHI_MIPI_CNTL0_DECODE_TO_RTERM GENMASK(15, 12)
> >> +#define HHI_MIPI_CNTL0_OUTPUT_EN BIT(3)
> >> +
> >> +#define HHI_MIPI_CNTL1 0x01
> >> +#define HHI_MIPI_CNTL1_CH0_CML_PDR_EN BIT(12)
> >> +#define HHI_MIPI_CNTL1_LP_ABILITY GENMASK(5, 4)
> >> +#define HHI_MIPI_CNTL1_LP_RESISTER BIT(3)
> >> +#define HHI_MIPI_CNTL1_INPUT_SETTING BIT(2)
> >> +#define HHI_MIPI_CNTL1_INPUT_SEL BIT(1)
> >> +#define HHI_MIPI_CNTL1_PRBS7_EN BIT(0)
> >> +
> >> +#define HHI_MIPI_CNTL2 0x02
> >> +#define HHI_MIPI_CNTL2_CH_PU GENMASK(31, 25)
> >> +#define HHI_MIPI_CNTL2_CH_CTL GENMASK(24, 19)
> >> +#define HHI_MIPI_CNTL2_CH0_DIGDR_EN BIT(18)
> >> +#define HHI_MIPI_CNTL2_CH_DIGDR_EN BIT(17)
> >> +#define HHI_MIPI_CNTL2_LPULPS_EN BIT(16)
> >> +#define HHI_MIPI_CNTL2_CH_EN(n) BIT(15 - (n))
> >> +#define HHI_MIPI_CNTL2_CH0_LP_CTL GENMASK(10, 1)
> >> +
> >> +struct phy_axg_mipi_pcie_analog_priv {
> >> + struct phy *phy;
> >> + unsigned int mode;
> >> + struct regmap *regmap;
> >> +};
> >> +
> >> +static const struct regmap_config phy_axg_mipi_pcie_analog_regmap_conf = {
> >> + .reg_bits = 8,
> >> + .val_bits = 32,
> >> + .reg_stride = 4,
> >> + .max_register = HHI_MIPI_CNTL2,
> >> +};
> >> +
> >> +static int phy_axg_mipi_pcie_analog_power_on(struct phy *phy)
> >> +{
> >> + struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> >> +
> >> + /* MIPI not supported yet */
> >> + if (priv->mode != PHY_TYPE_PCIE)
> >> + return -EINVAL;
> >> +
> >> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> + HHI_MIPI_CNTL0_BANDGAP, HHI_MIPI_CNTL0_BANDGAP);
> >> +
> >> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> + HHI_MIPI_CNTL0_ENABLE, HHI_MIPI_CNTL0_ENABLE);
> >> + return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_power_off(struct phy *phy)
> >> +{
> >> + struct phy_axg_mipi_pcie_analog_priv *priv = phy_get_drvdata(phy);
> >> +
> >> + /* MIPI not supported yet */
> >> + if (priv->mode != PHY_TYPE_PCIE)
> >> + return -EINVAL;
> >> +
> >> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> + HHI_MIPI_CNTL0_BANDGAP, 0);
> >> + regmap_update_bits(priv->regmap, HHI_MIPI_CNTL0,
> >> + HHI_MIPI_CNTL0_ENABLE, 0);
> >> + return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_init(struct phy *phy)
> >> +{
> >> + return 0;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_exit(struct phy *phy)
> >> +{
> >> + return 0;
> >> +}
> >> +
> >> +static const struct phy_ops phy_axg_mipi_pcie_analog_ops = {
> >> + .init = phy_axg_mipi_pcie_analog_init,
> >> + .exit = phy_axg_mipi_pcie_analog_exit,
> >> + .power_on = phy_axg_mipi_pcie_analog_power_on,
> >> + .power_off = phy_axg_mipi_pcie_analog_power_off,
> >> + .owner = THIS_MODULE,
> >> +};
> >> +
> >> +static struct phy *phy_axg_mipi_pcie_analog_xlate(struct device *dev,
> >> + struct of_phandle_args *args)
> >> +{
> >> + struct phy_axg_mipi_pcie_analog_priv *priv = dev_get_drvdata(dev);
> >> + unsigned int mode;
> >> +
> >> + if (args->args_count != 1) {
> >> + dev_err(dev, "invalid number of arguments\n");
> >> + return ERR_PTR(-EINVAL);
> >> + }
> >> +
> >> + mode = args->args[0];
> >> +
> >> + /* MIPI mode is not supported yet */
> >> + if (mode != PHY_TYPE_PCIE) {
> >> + dev_err(dev, "invalid phy mode select argument\n");
> >> + return ERR_PTR(-EINVAL);
> >> + }
> >> +
> >> + priv->mode = mode;
> >> + return priv->phy;
> >> +}
> >> +
> >> +static int phy_axg_mipi_pcie_analog_probe(struct platform_device *pdev)
> >> +{
> >> + struct phy_provider *phy;
> >> + struct device *dev = &pdev->dev;
> >> + struct phy_axg_mipi_pcie_analog_priv *priv;
> >> + struct device_node *np = dev->of_node;
> >> + struct regmap *map;
> >> + struct resource *res;
> >> + void __iomem *base;
> >> + int ret;
> >> +
> >> + priv = devm_kmalloc(dev, sizeof(*priv), GFP_KERNEL);
> >> + if (!priv)
> >> + return -ENOMEM;
> >> +
> >> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> >> + base = devm_ioremap_resource(dev, res);
> >> + if (IS_ERR(base)) {
> >> + dev_err(dev, "failed to get regmap base\n");
> >> + return PTR_ERR(base);
> >> + }
> >> +
> >> + map = devm_regmap_init_mmio(dev, base,
> >> + &phy_axg_mipi_pcie_analog_regmap_conf);
> >> + if (IS_ERR(map)) {
> >> + dev_err(dev, "failed to get HHI regmap\n");
> >> + return PTR_ERR(map);
> >> + }
> >> + priv->regmap = map;
> >> +
> >> + priv->phy = devm_phy_create(dev, np, &phy_axg_mipi_pcie_analog_ops);
> >> + if (IS_ERR(priv->phy)) {
> >> + ret = PTR_ERR(priv->phy);
> >> + if (ret != -EPROBE_DEFER)
> >> + dev_err(dev, "failed to create PHY\n");
> >> + return ret;
> >> + }
> >> +
> >> + phy_set_drvdata(priv->phy, priv);
> >> + dev_set_drvdata(dev, priv);
> >> +
> >> + phy = devm_of_phy_provider_register(dev,
> >> + phy_axg_mipi_pcie_analog_xlate);
> >> +
> >> + return PTR_ERR_OR_ZERO(phy);
> >> +}
> >> +
> >> +static const struct of_device_id phy_axg_mipi_pcie_analog_of_match[] = {
> >> + {
> >> + .compatible = "amlogic,axg-mipi-pcie-analog-phy",
> >> + },
> >> + { },
> >> +};
> >> +MODULE_DEVICE_TABLE(of, phy_axg_mipi_pcie_analog_of_match);
> >> +
> >> +static struct platform_driver phy_axg_mipi_pcie_analog_driver = {
> >> + .probe = phy_axg_mipi_pcie_analog_probe,
> >> + .driver = {
> >> + .name = "phy-axg-mipi-pcie-analog",
> >> + .of_match_table = phy_axg_mipi_pcie_analog_of_match,
> >> + },
> >> +};
> >> +module_platform_driver(phy_axg_mipi_pcie_analog_driver);
> >> +
> >> +MODULE_AUTHOR("Remi Pommarel <repk@triplefau.lt>");
> >> +MODULE_DESCRIPTION("Amlogic AXG MIPI + PCIE analog PHY driver");
> >> +MODULE_LICENSE("GPL v2");
> >> --
> >> 2.24.1
> >>
>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2020-03-04 10:44 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-23 23:29 [PATCH v6 0/7] PCI: amlogic: Make PCIe working reliably on AXG platforms Remi Pommarel
2020-01-23 23:29 ` [PATCH v6 1/7] dt-bindings: Add AXG PCIE PHY bindings Remi Pommarel
2020-01-24 8:27 ` Remi Pommarel
2020-01-23 23:29 ` [PATCH v6 2/7] dt-bindings: Add AXG shared MIPI/PCIE analog " Remi Pommarel
2020-01-24 8:28 ` Remi Pommarel
2020-01-23 23:29 ` [PATCH v6 3/7] dt-bindings: PCI: meson: Update PCIE bindings documentation Remi Pommarel
2020-01-24 8:30 ` Remi Pommarel
2020-01-23 23:29 ` [PATCH v6 4/7] arm64: dts: meson-axg: Add PCIE PHY nodes Remi Pommarel
2020-01-24 8:34 ` Remi Pommarel
2020-01-23 23:29 ` [PATCH v6 5/7] phy: amlogic: Add Amlogic AXG MIPI/PCIE analog PHY Driver Remi Pommarel
2020-01-24 8:32 ` Remi Pommarel
2020-03-03 17:19 ` Lorenzo Pieralisi
2020-03-04 9:08 ` Neil Armstrong
2020-03-04 10:44 ` Lorenzo Pieralisi [this message]
2020-01-23 23:29 ` [PATCH v6 6/7] phy: amlogic: Add Amlogic AXG PCIE " Remi Pommarel
2020-03-04 10:47 ` Neil Armstrong
2020-03-04 11:01 ` Kishon Vijay Abraham I
2020-03-04 13:08 ` Remi Pommarel
2020-03-05 4:56 ` Kishon Vijay Abraham I
2020-03-05 7:00 ` Neil Armstrong
2020-01-23 23:29 ` [PATCH v6 7/7] PCI: amlogic: Use AXG PCIE Remi Pommarel
2020-01-24 8:35 ` Remi Pommarel
2020-01-24 8:02 ` [PATCH v6 0/7] PCI: amlogic: Make PCIe working reliably on AXG platforms Neil Armstrong
2020-01-24 8:37 ` Remi Pommarel
2020-02-24 14:15 ` Lorenzo Pieralisi
2020-02-29 16:07 ` Kevin Hilman
2020-02-29 17:10 ` Remi Pommarel
2020-03-03 15:03 ` Lorenzo Pieralisi
2020-03-04 12:28 ` Lorenzo Pieralisi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200304104434.GA6613@e121166-lin.cambridge.arm.com \
--to=lorenzo.pieralisi@arm.com \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=jbrunet@baylibre.com \
--cc=khilman@baylibre.com \
--cc=kishon@ti.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=narmstrong@baylibre.com \
--cc=repk@triplefau.lt \
--cc=robh+dt@kernel.org \
--cc=yue.wang@Amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).