From: Neil Armstrong <narmstrong@baylibre.com>
To: agust@denx.de, Tom Rini <trini@konsulko.com>
Cc: mjourdan@baylibre.com, u-boot@lists.denx.de,
linux-amlogic@lists.infradead.org, jbrunet@baylibre.com
Subject: Re: [PATCH u-boot 00/11] meson: add support for Video Output
Date: Mon, 28 Jan 2019 10:10:10 +0100 [thread overview]
Message-ID: <f18da31d-d1ac-efcb-099c-cdfcd225fd60@baylibre.com> (raw)
In-Reply-To: <20190115161759.1657-1-narmstrong@baylibre.com>
Hi Anatolij, Tom,
Could you have a look at patches 2, 3 & 4 ?
Is there a more dedicated reviewer for this ?
Thanks,
Neil
On 15/01/2019 17:17, Neil Armstrong wrote:
> This patchset adds support for CVBS and/or HDMI output for Amlogic
> Meson GX SoCs (GXBB, GXL and GXM) based on the Linux Meson DRM driver
> ported to the U-Boot Video DM model. It supports only the "DMT" video
> modes reported by the monitors since AVI InfoFrame management is
> missing from the U-Boot video model.
>
> The port includes some changes in the dw-hdmi driver to support custom
> PHY calls and support for the ColorSpace converter since the
> Amlogic Meson GX video pipeline can only output un YUV444 mode, thus
> activating the CSC is needed to output RGB for HDMI.
>
> Video Support needs some tweaks in the DT like the u-boot,dm-pre-reloc for
> the VPU node and a tweak to access the HHI registers from the DW-HDMI
> glue driver. A port of a linux patch is also necessary to hook a regulator
> to enable HDMI.
>
> Finally, it enables console mux and console env for all Amlogic boards
> and enabled Video Support for the Libre Computer AML-S905X-CC board.
>
> Jorge Ramirez-Ortiz (2):
> video: dw_hdmi: support SoC specific read/write ops
> video: dw_hdmi: add support for color conversion
>
> Maxime Jourdan (6):
> power: domain: meson-gx-pwrc-vpu: add missing depends
> arm64: dts: meson-gx: vpu should be probed before relocation
> arm64: dts: meson-gx: add hhi reg entry to hdmi_tx
> arm: meson: board-gx: Setup VPU in fdt
> arm: meson64: enable console mux and console env by default
> arm: libretech-cc: enable video by default
>
> Neil Armstrong (3):
> video: Add Meson Video Processing Unit Driver
> arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply
> configs: meson64: use vidconsole and usbkbd if enabled
>
> arch/arm/dts/meson-gx-u-boot.dtsi | 21 +
> arch/arm/dts/meson-gxbb-nanopi-k2-u-boot.dtsi | 7 +
> arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi | 7 +
> .../meson-gxl-s905x-khadas-vim-u-boot.dtsi | 7 +
> arch/arm/dts/meson-gxl-s905x-khadas-vim.dts | 1 +
> .../meson-gxl-s905x-libretech-cc-u-boot.dtsi | 7 +
> arch/arm/dts/meson-gxl-s905x-libretech-cc.dts | 1 +
> arch/arm/dts/meson-gxl-s905x-p212-u-boot.dtsi | 7 +
> arch/arm/dts/meson-gxl-s905x-p212.dts | 1 +
> .../arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi | 7 +
> arch/arm/dts/meson-gxm-khadas-vim2.dts | 1 +
> arch/arm/include/asm/arch-meson/meson-vpu.h | 13 +
> arch/arm/mach-meson/board-gx.c | 5 +
> configs/khadas-vim2_defconfig | 2 +
> configs/khadas-vim_defconfig | 2 +
> configs/libretech-cc_defconfig | 8 +
> configs/odroid-c2_defconfig | 2 +
> configs/p212_defconfig | 2 +
> drivers/power/domain/Kconfig | 2 +-
> drivers/video/Kconfig | 2 +
> drivers/video/Makefile | 1 +
> drivers/video/dw_hdmi.c | 267 ++-
> drivers/video/meson/Kconfig | 12 +
> drivers/video/meson/Makefile | 9 +
> drivers/video/meson/meson_canvas.c | 45 +
> drivers/video/meson/meson_dw_hdmi.c | 445 +++++
> drivers/video/meson/meson_dw_hdmi.h | 134 ++
> drivers/video/meson/meson_plane.c | 177 ++
> drivers/video/meson/meson_registers.h | 1393 ++++++++++++++++
> drivers/video/meson/meson_vclk.c | 893 ++++++++++
> drivers/video/meson/meson_venc.c | 1464 +++++++++++++++++
> drivers/video/meson/meson_vpu.c | 211 +++
> drivers/video/meson/meson_vpu.h | 97 ++
> drivers/video/meson/meson_vpu_init.c | 440 +++++
> drivers/video/meson/simplefb_common.c | 29 +
> drivers/video/meson/simplefb_common.h | 21 +
> include/configs/meson64.h | 23 +
> include/dw_hdmi.h | 74 +
> include/media_bus_format.h | 156 ++
> 39 files changed, 5992 insertions(+), 4 deletions(-)
> create mode 100644 arch/arm/dts/meson-gx-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxbb-nanopi-k2-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxbb-odroidc2-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxl-s905x-khadas-vim-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxl-s905x-libretech-cc-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxl-s905x-p212-u-boot.dtsi
> create mode 100644 arch/arm/dts/meson-gxm-khadas-vim2-u-boot.dtsi
> create mode 100644 arch/arm/include/asm/arch-meson/meson-vpu.h
> create mode 100644 drivers/video/meson/Kconfig
> create mode 100644 drivers/video/meson/Makefile
> create mode 100644 drivers/video/meson/meson_canvas.c
> create mode 100644 drivers/video/meson/meson_dw_hdmi.c
> create mode 100644 drivers/video/meson/meson_dw_hdmi.h
> create mode 100644 drivers/video/meson/meson_plane.c
> create mode 100644 drivers/video/meson/meson_registers.h
> create mode 100644 drivers/video/meson/meson_vclk.c
> create mode 100644 drivers/video/meson/meson_venc.c
> create mode 100644 drivers/video/meson/meson_vpu.c
> create mode 100644 drivers/video/meson/meson_vpu.h
> create mode 100644 drivers/video/meson/meson_vpu_init.c
> create mode 100644 drivers/video/meson/simplefb_common.c
> create mode 100644 drivers/video/meson/simplefb_common.h
> create mode 100644 include/media_bus_format.h
>
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
prev parent reply other threads:[~2019-01-28 9:10 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-15 16:17 [PATCH u-boot 00/11] meson: add support for Video Output Neil Armstrong
2019-01-15 16:17 ` [PATCH u-boot 01/11] power: domain: meson-gx-pwrc-vpu: add missing depends Neil Armstrong
2019-01-28 19:58 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 02/11] video: dw_hdmi: support SoC specific read/write ops Neil Armstrong
2019-01-28 16:00 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 03/11] video: dw_hdmi: add support for color conversion Neil Armstrong
2019-01-28 16:01 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 04/11] video: Add Meson Video Processing Unit Driver Neil Armstrong
2019-01-28 19:56 ` Anatolij Gustschin
2019-01-29 8:26 ` Neil Armstrong
2019-01-29 10:28 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 05/11] arm64: dts: meson-gx: vpu should be probed before relocation Neil Armstrong
2019-01-15 16:17 ` [PATCH u-boot 06/11] arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply Neil Armstrong
2019-01-15 16:17 ` [PATCH u-boot 07/11] arm64: dts: meson-gx: add hhi reg entry to hdmi_tx Neil Armstrong
2019-01-15 16:17 ` [PATCH u-boot 08/11] arm: meson: board-gx: Setup VPU in fdt Neil Armstrong
2019-01-28 20:07 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 09/11] configs: meson64: use vidconsole and usbkbd if enabled Neil Armstrong
2019-01-28 20:09 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 10/11] arm: meson64: enable console mux and console env by default Neil Armstrong
2019-01-28 20:11 ` Anatolij Gustschin
2019-01-15 16:17 ` [PATCH u-boot 11/11] arm: libretech-cc: enable video " Neil Armstrong
2019-01-28 20:12 ` Anatolij Gustschin
2019-01-28 9:10 ` Neil Armstrong [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f18da31d-d1ac-efcb-099c-cdfcd225fd60@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=agust@denx.de \
--cc=jbrunet@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=mjourdan@baylibre.com \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).