[PATCH 6/6] arm64: dts: allwinner: bananapi-m64: Enable S070WV20-CT16 DSI panel

From: Jagan Teki <jagan@amarulasolutions.com>
To: Andrzej Hajda <a.hajda@samsung.com>,
	Laurent Pinchart <Laurent.pinchart@ideasonboard.com>,
	Chen-Yu Tsai <wens@csie.org>,
	Maxime Ripard <maxime.ripard@bootlin.com>,
	David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	dri-devel@lists.freedesktop.org, linux-sunxi@googlegroups.com,
	Jagan Teki <jagan@amarulasolutions.com>,
	Michael Trimarchi <michael@amarulasolutions.com>,
	linux-amarula@amarulasolutions.com,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH 6/6] arm64: dts: allwinner: bananapi-m64: Enable S070WV20-CT16 DSI panel
Date: Fri, 15 Mar 2019 18:38:25 +0530	[thread overview]
Message-ID: <20190315130825.9005-7-jagan@amarulasolutions.com> (raw)
In-Reply-To: <20190315130825.9005-1-jagan@amarulasolutions.com>

This patch add support for Bananapi S070WV20-CT16 DSI panel to
BPI-M64 board.

Bananapi S070WV20-CT16 is a pure RGB output panel with ICN6211 DSI/RGB
convertor bridge, so enable bridge along with associated panel.

DSI panel connected via board DSI port with,
- DLDO1 as VCC-DSI supply
- PD6 gpio for reset pin
- PD5 gpio for backlight enable pin
- PD7 gpio for backlight vdd supply

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
---
 .../dts/allwinner/sun50i-a64-bananapi-m64.dts | 63 +++++++++++++++++++
 1 file changed, 63 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 7793ebb5d2b8..f31083aa4521 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -45,6 +45,7 @@
 #include "sun50i-a64.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "BananaPi-M64";
@@ -56,6 +57,15 @@
 		serial1 = &uart1;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <1 2 4 8 16 32 64 128 512>;
+		default-brightness-level = <2>;
+		enable-gpios = <&pio 3 5 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PD5 */
+		power-supply = <&reg_vdd_backlight>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -91,6 +101,26 @@
 		};
 	};
 
+	panel-connector {
+		compatible = "bananapi,s070wv20-ct16", "simple-panel";
+
+		port {
+			backlight = <&backlight>;
+			panel_ep: endpoint {
+				remote-endpoint = <&bridge_out_ep>;
+			};
+		};
+	};
+
+	reg_vdd_backlight: vdd-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-backlight";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* LCD-PWR-EN: PD7 */
+		enable-active-high;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
@@ -116,6 +146,33 @@
 	status = "okay";
 };
 
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	vcc-dsi-supply = <&reg_dldo1>;		/* VCC3V3-DSI */
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bridge@0 {
+		compatible = "bananapi,icn6211", "chipone, icn6211";
+		reg = <0>;
+		reset-gpios = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD6 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+
+			bridge_out_ep: endpoint {
+				remote-endpoint = <&panel_ep>;
+			};
+		};
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -208,6 +265,12 @@
 	status = "okay";
 };
 
+&r_pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_pwm_pin>;
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
-- 
2.18.0.321.gffc6fa0e3


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
