From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: stefan.wahren@i2se.com, Florian Fainelli <f.fainelli@gmail.com>,
Ray Jui <rjui@broadcom.com>,
Scott Branden <sbranden@broadcom.com>,
bcm-kernel-feedback-list@broadcom.com,
Eric Anholt <eric@anholt.net>
Cc: linux-arm-kernel@lists.infradead.org, ptesarik@suse.com,
sboyd@kernel.org, viresh.kumar@linaro.org,
mturquette@baylibre.com, linux-pm@vger.kernel.org,
rjw@rjwysocki.net, linux-kernel@vger.kernel.org,
Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
linux-rpi-kernel@lists.infradead.org, linux-clk@vger.kernel.org,
mbrugger@suse.de, ssuloev@orpaltech.com
Subject: [RFC v2 1/5] clk: bcm2835: set CLK_GET_RATE_NOCACHE on CPU clocks
Date: Mon, 20 May 2019 12:47:03 +0200 [thread overview]
Message-ID: <20190520104708.11980-2-nsaenzjulienne@suse.de> (raw)
In-Reply-To: <20190520104708.11980-1-nsaenzjulienne@suse.de>
Raspberry Pi's firmware is responsible for updating the cpu clocks and
pll. This makes sure we get the right rates anytime.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
---
drivers/clk/bcm/clk-bcm2835.c | 6 ++++--
1 file changed, 4 insertions(+), 2 deletions(-)
diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c
index 770bb01f523e..c2772dfb155a 100644
--- a/drivers/clk/bcm/clk-bcm2835.c
+++ b/drivers/clk/bcm/clk-bcm2835.c
@@ -411,6 +411,7 @@ struct bcm2835_pll_data {
u32 reference_enable_mask;
/* Bit in CM_LOCK to indicate when the PLL has locked. */
u32 lock_mask;
+ u32 flags;
const struct bcm2835_pll_ana_bits *ana;
@@ -1299,7 +1300,7 @@ static struct clk_hw *bcm2835_register_pll(struct bcm2835_cprman *cprman,
init.num_parents = 1;
init.name = data->name;
init.ops = &bcm2835_pll_clk_ops;
- init.flags = CLK_IGNORE_UNUSED;
+ init.flags = data->flags | CLK_IGNORE_UNUSED;
pll = kzalloc(sizeof(*pll), GFP_KERNEL);
if (!pll)
@@ -1660,6 +1661,7 @@ static const struct bcm2835_clk_desc clk_desc_array[] = {
.ana_reg_base = A2W_PLLB_ANA0,
.reference_enable_mask = A2W_XOSC_CTRL_PLLB_ENABLE,
.lock_mask = CM_LOCK_FLOCKB,
+ .flags = CLK_GET_RATE_NOCACHE,
.ana = &bcm2835_ana_default,
@@ -1674,7 +1676,7 @@ static const struct bcm2835_clk_desc clk_desc_array[] = {
.load_mask = CM_PLLB_LOADARM,
.hold_mask = CM_PLLB_HOLDARM,
.fixed_divider = 1,
- .flags = CLK_SET_RATE_PARENT),
+ .flags = CLK_SET_RATE_PARENT | CLK_GET_RATE_NOCACHE),
/*
* PLLC is the core PLL, used to drive the core VPU clock.
--
2.21.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-05-20 10:48 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-20 10:47 [RFC v2 0/5] cpufreq support for the Raspberry Pi Nicolas Saenz Julienne
2019-05-20 10:47 ` Nicolas Saenz Julienne [this message]
2019-05-20 11:42 ` [RFC v2 1/5] clk: bcm2835: set CLK_GET_RATE_NOCACHE on CPU clocks Stefan Wahren
2019-05-20 10:47 ` [RFC v2 2/5] clk: bcm2835: set pllb_arm divisor as readonly Nicolas Saenz Julienne
2019-05-20 11:43 ` Stefan Wahren
2019-05-20 10:47 ` [RFC v2 3/5] clk: bcm2835: use firmware interface to update pllb Nicolas Saenz Julienne
2019-05-20 12:11 ` Stefan Wahren
2019-05-20 12:14 ` Stefan Wahren
2019-05-21 12:40 ` Stefan Wahren
2019-05-21 15:47 ` Nicolas Saenz Julienne
2019-05-21 21:43 ` Stefan Wahren
2019-05-23 8:51 ` Nicolas Saenz Julienne
2019-05-20 12:43 ` Oliver Neukum
2019-05-21 11:39 ` Nicolas Saenz Julienne
2019-05-21 12:14 ` Petr Tesarik
2019-05-21 12:18 ` Nicolas Saenz Julienne
2019-05-20 10:47 ` [RFC v2 4/5] dts: bcm2837: add per-cpu clock devices Nicolas Saenz Julienne
2019-05-20 12:19 ` Stefan Wahren
2019-05-21 11:40 ` Nicolas Saenz Julienne
2019-05-20 10:47 ` [RFC v2 5/5] cpufreq: add driver for Raspbery Pi Nicolas Saenz Julienne
2019-05-20 10:51 ` Viresh Kumar
2019-05-20 12:30 ` Stefan Wahren
2019-05-20 10:51 ` [RFC v2 0/5] cpufreq support for the Raspberry Pi Viresh Kumar
2019-05-21 12:02 ` Nicolas Saenz Julienne
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190520104708.11980-2-nsaenzjulienne@suse.de \
--to=nsaenzjulienne@suse.de \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=eric@anholt.net \
--cc=f.fainelli@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=mbrugger@suse.de \
--cc=mturquette@baylibre.com \
--cc=ptesarik@suse.com \
--cc=rjui@broadcom.com \
--cc=rjw@rjwysocki.net \
--cc=sboyd@kernel.org \
--cc=sbranden@broadcom.com \
--cc=ssuloev@orpaltech.com \
--cc=stefan.wahren@i2se.com \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).