linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>,
	devicetree@vger.kernel.org, Li Yang <leoyang.li@nxp.com>,
	Claudiu Manoil <claudiu.manoil@nxp.com>,
	Vladimir Oltean <olteanv@gmail.com>,
	Shawn Guo <shawnguo@kernel.org>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 4.9 118/251] ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
Date: Thu, 16 Jan 2020 12:34:27 -0500	[thread overview]
Message-ID: <20200116173641.22137-78-sashal@kernel.org> (raw)
In-Reply-To: <20200116173641.22137-1-sashal@kernel.org>

From: Vladimir Oltean <olteanv@gmail.com>

[ Upstream commit c7861adbe37f576931650ad8ef805e0c47564b9a ]

Each eTSEC MAC has its own TBI (SGMII) PCS and private MDIO bus.
But due to a DTS oversight, both SGMII-compatible MACs of the LS1021 SoC
are pointing towards the same internal PCS. Therefore nobody is
controlling the internal PCS of eTSEC0.

Upon initial ndo_open, the SGMII link is ok by virtue of U-boot
initialization. But upon an ifdown/ifup sequence, the code path from
ndo_open -> init_phy -> gfar_configure_serdes does not get executed for
the PCS of eTSEC0 (and is executed twice for MAC eTSEC1). So the SGMII
link remains down for eTSEC0. On the LS1021A-TWR board, to signal this
failure condition, the PHY driver keeps printing
'803x_aneg_done: SGMII link is not ok'.

Also, it changes compatible of mdio0 to "fsl,etsec2-mdio" to match
mdio1 device.

Fixes: 055223d4d22d ("ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ls1021a-twr.dts |  9 ++++++++-
 arch/arm/boot/dts/ls1021a.dtsi    | 11 ++++++++++-
 2 files changed, 18 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/ls1021a-twr.dts
index 44715c8ef756..72a3fc63d0ec 100644
--- a/arch/arm/boot/dts/ls1021a-twr.dts
+++ b/arch/arm/boot/dts/ls1021a-twr.dts
@@ -143,7 +143,7 @@
 };
 
 &enet0 {
-	tbi-handle = <&tbi1>;
+	tbi-handle = <&tbi0>;
 	phy-handle = <&sgmii_phy2>;
 	phy-connection-type = "sgmii";
 	status = "okay";
@@ -222,6 +222,13 @@
 	sgmii_phy2: ethernet-phy@2 {
 		reg = <0x2>;
 	};
+	tbi0: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&mdio1 {
 	tbi1: tbi-phy@1f {
 		reg = <0x1f>;
 		device_type = "tbi-phy";
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
index 825f6eae3d1c..27133c3a4b12 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -505,13 +505,22 @@
 		};
 
 		mdio0: mdio@2d24000 {
-			compatible = "gianfar";
+			compatible = "fsl,etsec2-mdio";
 			device_type = "mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2d24000 0x0 0x4000>;
 		};
 
+		mdio1: mdio@2d64000 {
+			compatible = "fsl,etsec2-mdio";
+			device_type = "mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0x2d64000 0x0 0x4000>,
+			      <0x0 0x2d50030 0x0 0x4>;
+		};
+
 		ptp_clock@2d10e00 {
 			compatible = "fsl,etsec-ptp";
 			reg = <0x0 0x2d10e00 0x0 0xb0>;
-- 
2.20.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2020-01-16 18:22 UTC|newest]

Thread overview: 34+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-16 17:33 [PATCH AUTOSEL 4.9 041/251] media: s5p-jpeg: Correct step and max values for V4L2_CID_JPEG_RESTART_INTERVAL Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 043/251] ASoC: imx-sgtl5000: put of nodes if finding codec fails Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 046/251] clk: sunxi-ng: sun8i-a23: Enable PLL-MIPI LDOs when ungating it Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 050/251] ARM: dts: lpc32xx: add required clocks property to keypad device node Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 051/251] ARM: dts: lpc32xx: reparent keypad controller to SIC1 Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 052/251] ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller variant Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 053/251] ARM: dts: lpc32xx: fix ARM PrimeCell LCD controller clocks property Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 054/251] ARM: dts: lpc32xx: phy3250: fix SD card regulator voltage Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 058/251] thermal: mediatek: fix register index error Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 085/251] clocksource/drivers/sun5i: Fail gracefully when clock rate is unavailable Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 086/251] clocksource/drivers/exynos_mct: Fix error path in timer resources initialization Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 087/251] mmc: sdhci-brcmstb: handle mmc_of_parse() errors during probe Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 088/251] ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used Sasha Levin
2020-01-16 17:33 ` [PATCH AUTOSEL 4.9 089/251] ARM: 8848/1: virt: Align GIC version check with arm64 counterpart Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 104/251] ARM: OMAP2+: Fix potentially uninitialized return value for _setup_reset() Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 110/251] soc/fsl/qe: Fix an error code in qe_pin_request() Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 111/251] spi: bcm2835aux: fix driver to not allow 65535 (=-1) cs-gpios Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 114/251] ARM: pxa: ssp: Fix "WARNING: invalid free of devm_ allocated data" Sasha Levin
2020-01-16 17:34 ` Sasha Levin [this message]
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 138/251] pwm: meson: Don't disable PWM when setting duty repeatedly Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 139/251] ARM: riscpc: fix lack of keyboard interrupts after irq conversion Sasha Levin
2020-01-16 17:34 ` [PATCH AUTOSEL 4.9 146/251] serial: stm32: fix transmit_chars when tx is stopped Sasha Levin
2020-01-16 17:35 ` [PATCH AUTOSEL 4.9 184/251] ASoC: sun4i-i2s: RX and TX counter registers are swapped Sasha Levin
2020-01-16 17:35 ` [PATCH AUTOSEL 4.9 205/251] net: stmmac: dwmac-meson8b: Fix signedness bug in probe Sasha Levin
2020-01-16 17:35 ` [PATCH AUTOSEL 4.9 207/251] net: ethernet: stmmac: Fix signedness bug in ipq806x_gmac_of_parse() Sasha Levin
2020-01-16 17:35 ` [PATCH AUTOSEL 4.9 210/251] net: stmmac: gmac4+: Not all Unicast addresses may be available Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 214/251] net: stmmac: fix length of PTP clock's name string Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 218/251] dmaengine: imx-sdma: fix size check for sdma script_number Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 224/251] mt7601u: fix bbp version check in mt7601u_wait_bbp_ready Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 229/251] spi: atmel: fix handling of cs_change set on non-last xfer Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 232/251] clk: samsung: exynos5420: Preserve CPU clocks configuration during suspend/resume Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 235/251] media: exynos4-is: Fix recursive locking in isp_video_release() Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 240/251] tty: serial: imx: use the sg count from dma_map_sg Sasha Levin
2020-01-16 17:36 ` [PATCH AUTOSEL 4.9 249/251] arm64: dts: juno: Fix UART frequency Sasha Levin

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200116173641.22137-78-sashal@kernel.org \
    --to=sashal@kernel.org \
    --cc=claudiu.manoil@nxp.com \
    --cc=devicetree@vger.kernel.org \
    --cc=leoyang.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=olteanv@gmail.com \
    --cc=shawnguo@kernel.org \
    --cc=stable@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).