From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: "Sasha Levin" <sashal@kernel.org>,
devicetree@vger.kernel.org,
"Alexandre Belloni" <alexandre.belloni@bootlin.com>,
"Karl Rudbæk Olsen" <karl@micro-technic.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 4.4 061/100] ARM: dts: at91: sama5d3: fix maximum peripheral clock rates
Date: Fri, 14 Feb 2020 11:23:45 -0500 [thread overview]
Message-ID: <20200214162425.21071-61-sashal@kernel.org> (raw)
In-Reply-To: <20200214162425.21071-1-sashal@kernel.org>
From: Alexandre Belloni <alexandre.belloni@bootlin.com>
[ Upstream commit ee0aa926ddb0bd8ba59e33e3803b3b5804e3f5da ]
Currently the maximum rate for peripheral clock is calculated based on a
typical 133MHz MCK. The maximum frequency is defined in the datasheet as a
ratio to MCK. Some sama5d3 platforms are using a 166MHz MCK. Update the
device trees to match the maximum rate based on 166MHz.
Reported-by: Karl Rudbæk Olsen <karl@micro-technic.com>
Fixes: d2e8190b7916 ("ARM: at91/dt: define sama5d3 clocks")
Link: https://lore.kernel.org/r/20200110172007.1253659-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/arm/boot/dts/sama5d3.dtsi | 28 ++++++++++++++--------------
arch/arm/boot/dts/sama5d3_can.dtsi | 4 ++--
arch/arm/boot/dts/sama5d3_uart.dtsi | 4 ++--
3 files changed, 18 insertions(+), 18 deletions(-)
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index a53279160f983..6b1894400ccca 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -1106,49 +1106,49 @@
usart0_clk: usart0_clk {
#clock-cells = <0>;
reg = <12>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart1_clk: usart1_clk {
#clock-cells = <0>;
reg = <13>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart2_clk: usart2_clk {
#clock-cells = <0>;
reg = <14>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
usart3_clk: usart3_clk {
#clock-cells = <0>;
reg = <15>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
twi0_clk: twi0_clk {
reg = <18>;
#clock-cells = <0>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi1_clk: twi1_clk {
#clock-cells = <0>;
reg = <19>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
twi2_clk: twi2_clk {
#clock-cells = <0>;
reg = <20>;
- atmel,clk-output-range = <0 16625000>;
+ atmel,clk-output-range = <0 41500000>;
};
mci0_clk: mci0_clk {
@@ -1164,19 +1164,19 @@
spi0_clk: spi0_clk {
#clock-cells = <0>;
reg = <24>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
spi1_clk: spi1_clk {
#clock-cells = <0>;
reg = <25>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
tcb0_clk: tcb0_clk {
#clock-cells = <0>;
reg = <26>;
- atmel,clk-output-range = <0 133000000>;
+ atmel,clk-output-range = <0 166000000>;
};
pwm_clk: pwm_clk {
@@ -1187,7 +1187,7 @@
adc_clk: adc_clk {
#clock-cells = <0>;
reg = <29>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
dma0_clk: dma0_clk {
@@ -1218,13 +1218,13 @@
ssc0_clk: ssc0_clk {
#clock-cells = <0>;
reg = <38>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
ssc1_clk: ssc1_clk {
#clock-cells = <0>;
reg = <39>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
sha_clk: sha_clk {
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/sama5d3_can.dtsi
index c5a3772741bf6..0fac79f75c06c 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/sama5d3_can.dtsi
@@ -37,13 +37,13 @@
can0_clk: can0_clk {
#clock-cells = <0>;
reg = <40>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
can1_clk: can1_clk {
#clock-cells = <0>;
reg = <41>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index 2511d748867bd..71818c7bfb673 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -42,13 +42,13 @@
uart0_clk: uart0_clk {
#clock-cells = <0>;
reg = <16>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
uart1_clk: uart1_clk {
#clock-cells = <0>;
reg = <17>;
- atmel,clk-output-range = <0 66000000>;
+ atmel,clk-output-range = <0 83000000>;
};
};
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-02-14 16:58 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200214162425.21071-1-sashal@kernel.org>
2020-02-14 16:22 ` [PATCH AUTOSEL 4.4 014/100] scsi: ufs: Fix ufshcd_probe_hba() reture value in case ufshcd_scsi_add_wlus() fails Sasha Levin
2020-02-14 16:23 ` Sasha Levin [this message]
2020-02-14 16:23 ` [PATCH AUTOSEL 4.4 062/100] ARM: dts: at91: sama5d3: define clock rate range for tcb1 Sasha Levin
2020-02-14 16:23 ` [PATCH AUTOSEL 4.4 066/100] ASoC: atmel: fix build error with CONFIG_SND_ATMEL_SOC_DMA=m Sasha Levin
2020-02-14 16:23 ` [PATCH AUTOSEL 4.4 072/100] iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE Sasha Levin
2020-02-14 16:24 ` [PATCH AUTOSEL 4.4 082/100] ARM: 8951/1: Fix Kexec compilation issue Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200214162425.21071-61-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=karl@micro-technic.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).