From: Keerthy <j-keerthy@ti.com>
To: Lokesh Vutla <lokeshvutla@ti.com>, Tero Kristo <t-kristo@ti.com>,
Nishanth Menon <nm@ti.com>, <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org, Rob Herring <robh+dt@kernel.org>,
Linux ARM Mailing List <linux-arm-kernel@lists.infradead.org>,
Device Tree Mailing List <devicetree@vger.kernel.org>
Subject: Re: [PATCH 3/6] arm64: dts: ti: k3-j721e: Add gpio nodes in wakeup domain
Date: Fri, 9 Aug 2019 20:24:29 +0530 [thread overview]
Message-ID: <48fca046-d683-bb6c-d848-24ffada6ed85@ti.com> (raw)
In-Reply-To: <20190809082947.30590-4-lokeshvutla@ti.com>
On 09/08/19 1:59 PM, Lokesh Vutla wrote:
> Similar to the gpio groups in main domain, there is one gpio group
> in wakup domain with 2 module instances in it. This gpio group pins
> out 84 lines(6 banks). Add DT node for these 2 gpio module instances.
Reviewed-by: Keerthy <j-keerthy@ti.com>
>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
> .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 34 +++++++++++++++++++
> 1 file changed, 34 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index e616c2481f51..555dc7b7aedc 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -87,4 +87,38 @@
> ti,sci-dst-id = <14>;
> ti,sci-rm-range-girq = <0x5>;
> };
> +
> + wkup_gpio0: gpio@42110000 {
> + compatible = "ti,j721e-gpio", "ti,keystone-gpio";
> + reg = <0x0 0x42110000 0x0 0x100>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&wkup_gpio_intr>;
> + interrupts = <113 0>, <113 1>, <113 2>,
> + <113 3>, <113 4>, <113 5>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + ti,ngpio = <84>;
> + ti,davinci-gpio-unbanked = <0>;
> + power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 113 0>;
> + clock-names = "gpio";
> + };
> +
> + wkup_gpio1: gpio@42100000 {
> + compatible = "ti,j721e-gpio", "ti,keystone-gpio";
> + reg = <0x0 0x42100000 0x0 0x100>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&wkup_gpio_intr>;
> + interrupts = <114 0>, <114 1>, <114 2>,
> + <114 3>, <114 4>, <114 5>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + ti,ngpio = <84>;
> + ti,davinci-gpio-unbanked = <0>;
> + power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 114 0>;
> + clock-names = "gpio";
> + };
> };
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-09 14:54 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-09 8:29 [PATCH 0/6] arm64: dts: ti: k3-j721e: Add gpio nodes Lokesh Vutla
2019-08-09 8:29 ` [PATCH 1/6] dt-bindings: gpio: davinci: Add new compatible for J721E SoCs Lokesh Vutla
2019-08-09 10:55 ` Keerthy
2019-08-15 7:46 ` Linus Walleij
2019-08-09 8:29 ` [PATCH 2/6] arm64: dts: ti: k3-j721e: Add gpio nodes in main domain Lokesh Vutla
2019-08-09 14:53 ` Keerthy
2019-08-09 8:29 ` [PATCH 3/6] arm64: dts: ti: k3-j721e: Add gpio nodes in wakeup domain Lokesh Vutla
2019-08-09 14:54 ` Keerthy [this message]
2019-08-09 8:29 ` [PATCH 4/6] arm64: dts: ti: k3-j721e-common-proc-board: Disable unused gpio modules Lokesh Vutla
2019-08-09 14:55 ` Keerthy
2019-08-09 8:29 ` [PATCH 5/6] dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E Lokesh Vutla
2019-08-21 21:02 ` Rob Herring
2019-08-26 10:26 ` Lokesh Vutla
2019-08-26 11:25 ` Rob Herring
2019-08-09 8:29 ` [PATCH 6/6] arm64: dts: k3-j721e: Add gpio-keys on common processor board Lokesh Vutla
2019-08-09 14:56 ` Keerthy
2019-08-20 12:49 ` [PATCH 0/6] arm64: dts: ti: k3-j721e: Add gpio nodes Lokesh Vutla
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=48fca046-d683-bb6c-d848-24ffada6ed85@ti.com \
--to=j-keerthy@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=lokeshvutla@ti.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=t-kristo@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).