Re: [PATCH v3 1/2] pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pins

From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To: Kevin Hilman <khilman@baylibre.com>
Cc: linus.luessing@c0d3.blue, jianxin.pan@amlogic.com,
	linus.walleij@linaro.org, linux-gpio@vger.kernel.org,
	ingrassia@epigenesys.com, linux-amlogic@lists.infradead.org,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v3 1/2] pinctrl: meson: meson8b: add the eth_rxd2 and eth_rxd3 pins
Date: Fri, 11 Jan 2019 20:52:05 +0100	[thread overview]
Message-ID: <CAFBinCB41iRf-5AdUir9Z9AYPGP4-yfD4B3Yn9+v+dxSFJoELA@mail.gmail.com> (raw)
In-Reply-To: <7hzhs8ovag.fsf@baylibre.com>

Hi Kevin,

On Fri, Jan 11, 2019 at 2:08 AM Kevin Hilman <khilman@baylibre.com> wrote:
>
> Martin Blumenstingl <martin.blumenstingl@googlemail.com> writes:
>
> > Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
> > Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
> > rely on the bootloader to set them up correctly.
> >
> > The vendor u-boot sources for Odroid-C1 use the following Ethernet
> > pinmux configuration:
> >   SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
> >   SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
> > This translates to the following pin groups in the mainline kernel:
> > - register 6 bit  0: eth_rxd1 (DIF_0_P)
> > - register 6 bit  1: eth_rxd0 (DIF_0_N)
> > - register 6 bit  2: eth_rx_dv (DIF_1_P)
> > - register 6 bit  3: eth_rx_clk (DIF_1_N)
> > - register 6 bit  6: eth_tx_en (DIF_3_P)
> > - register 6 bit  8: eth_ref_clk (DIF_3_N)
> > - register 6 bit  9: eth_mdc (DIF_4_P)
> > - register 6 bit 10: eth_mdio_en (DIF_4_N)
> > - register 6 bit 11: eth_tx_clk (GPIOH_9)
> > - register 6 bit 12: eth_txd2 (GPIOH_8)
> > - register 6 bit 13: eth_txd3 (GPIOH_7)
> > - register 7 bit 20: eth_txd0_0 (GPIOH_6)
> > - register 7 bit 21: eth_txd1_0 (GPIOH_5)
> > - register 7 bit 22: eth_rxd3 (DIF_2_P)
> > - register 7 bit 23: eth_rxd2 (DIF_2_N)
> >
> > All functions except eth_rxd2 and eth_rxd3 are already supported by the
> > pinctrl-meson8b driver.
> >
> > Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
> > Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>
> Reviewed-by: Kevin Hilman <khilman@baylibre.com>
thank you for reviewing this!

I just realized that I forgot to CC the linux-gpio mailing list as
well as Linus Walleij on this patch (fixing that with this mail) -
sorry for that.
right now this patch is applied to linux-amlogic.git's v5.1/dt branch.
please let me know whether you would like to keep it in your tree or
if you would like me to re-send it (including Linus and the linux-gpio
list this time...)

Regards
Martin

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel