Re: [PATCH v8 05/14] media: rkisp1: add Rockchip ISP1 subdev driver

[Helen Koike <helen.koike@collabora.com>]

Hi Sakari,

Thanks for your review. I just have some comments/questions below.

On 8/8/19 6:14 AM, Sakari Ailus wrote:
> Hi Helen,
> 
> On Tue, Jul 30, 2019 at 03:42:47PM -0300, Helen Koike wrote:
>> From: Jacob Chen <jacob2.chen@rock-chips.com>
>>
>> Add the subdev driver for rockchip isp1.
>>
>> Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
>> Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
>> Signed-off-by: Yichong Zhong <zyc@rock-chips.com>
>> Signed-off-by: Jacob Chen <cc@rock-chips.com>
>> Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
>> Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
>> Signed-off-by: Allon Huang <allon.huang@rock-chips.com>
>> Signed-off-by: Tomasz Figa <tfiga@chromium.org>
>> [fixed unknown entity type / switched to PIXEL_RATE]
>> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
>> [update for upstream]
>> Signed-off-by: Helen Koike <helen.koike@collabora.com>
>>
>> ---
>>
>> Changes in v8: None
>> Changes in v7:
>> - fixed warning because of unknown entity type
>> - fixed v4l2-compliance errors regarding rkisp1 formats, try formats
>> and default values
>> - fix typo riksp1/rkisp1
>> - redesign: remove mipi/csi subdevice, sensors connect directly to the
>> isp subdevice in the media topology now. As a consequence, remove the
>> hack in mipidphy_g_mbus_config() where information from the sensor was
>> being propagated through the topology.
>> - From the old dphy:
>>         * cache get_remote_sensor() in s_stream
>>         * use V4L2_CID_PIXEL_RATE instead of V4L2_CID_LINK_FREQ
>> - Replace stream state with a boolean
>> - code styling and checkpatch fixes
>> - fix stop_stream (return after calling stop, do not reenable the stream)
>> - fix rkisp1_isp_sd_get_selection when V4L2_SUBDEV_FORMAT_TRY is set
>> - fix get format in output (isp_sd->out_fmt.mbus_code was being ignored)
>> - s/intput/input
>> - remove #define sd_to_isp_sd(_sd), add a static inline as it will be
>> reused by the capture
>>
>>  drivers/media/platform/rockchip/isp1/rkisp1.c | 1286 +++++++++++++++++
>>  drivers/media/platform/rockchip/isp1/rkisp1.h |  111 ++
>>  2 files changed, 1397 insertions(+)
>>  create mode 100644 drivers/media/platform/rockchip/isp1/rkisp1.c
>>  create mode 100644 drivers/media/platform/rockchip/isp1/rkisp1.h
>>
>> diff --git a/drivers/media/platform/rockchip/isp1/rkisp1.c b/drivers/media/platform/rockchip/isp1/rkisp1.c
>> new file mode 100644
>> index 000000000000..6d0c0ffb5e03
>> --- /dev/null
>> +++ b/drivers/media/platform/rockchip/isp1/rkisp1.c
>> @@ -0,0 +1,1286 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +/*
>> + * Rockchip isp1 driver
>> + *
>> + * Copyright (C) 2017 Rockchip Electronics Co., Ltd.
>> + */
>> +
>> +#include <linux/iopoll.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/phy/phy-mipi-dphy.h>
>> +#include <linux/pm_runtime.h>
>> +#include <linux/videodev2.h>
>> +#include <linux/vmalloc.h>
>> +#include <media/v4l2-event.h>
>> +
>> +#include "common.h"
>> +#include "regs.h"
>> +
>> +#define CIF_ISP_INPUT_W_MAX		4032
>> +#define CIF_ISP_INPUT_H_MAX		3024
>> +#define CIF_ISP_INPUT_W_MIN		32
>> +#define CIF_ISP_INPUT_H_MIN		32
>> +#define CIF_ISP_OUTPUT_W_MAX		CIF_ISP_INPUT_W_MAX
>> +#define CIF_ISP_OUTPUT_H_MAX		CIF_ISP_INPUT_H_MAX
>> +#define CIF_ISP_OUTPUT_W_MIN		CIF_ISP_INPUT_W_MIN
>> +#define CIF_ISP_OUTPUT_H_MIN		CIF_ISP_INPUT_H_MIN
>> +
>> +/*
>> + * NOTE: MIPI controller and input MUX are also configured in this file,
>> + * because ISP Subdev is not only describe ISP submodule(input size,format,
>> + * output size, format), but also a virtual route device.
>> + */
>> +
>> +/*
>> + * There are many variables named with format/frame in below code,
>> + * please see here for their meaning.
>> + *
>> + * Cropping regions of ISP
>> + *
>> + * +---------------------------------------------------------+
>> + * | Sensor image                                            |
>> + * | +---------------------------------------------------+   |
>> + * | | ISP_ACQ (for black level)                         |   |
>> + * | | in_frm                                            |   |
>> + * | | +--------------------------------------------+    |   |
>> + * | | |    ISP_OUT                                 |    |   |
>> + * | | |    in_crop                                 |    |   |
>> + * | | |    +---------------------------------+     |    |   |
>> + * | | |    |   ISP_IS                        |     |    |   |
>> + * | | |    |   rkisp1_isp_subdev: out_crop   |     |    |   |
>> + * | | |    +---------------------------------+     |    |   |
>> + * | | +--------------------------------------------+    |   |
>> + * | +---------------------------------------------------+   |
>> + * +---------------------------------------------------------+
>> + */
>> +
>> +static inline struct rkisp1_device *sd_to_isp_dev(struct v4l2_subdev *sd)
>> +{
>> +	return container_of(sd->v4l2_dev, struct rkisp1_device, v4l2_dev);
>> +}
>> +
>> +/* Get sensor by enabled media link */
>> +static struct v4l2_subdev *get_remote_sensor(struct v4l2_subdev *sd)
>> +{
>> +	struct media_pad *local, *remote;
>> +	struct media_entity *sensor_me;
>> +
>> +	local = &sd->entity.pads[RKISP1_ISP_PAD_SINK];
>> +	remote = media_entity_remote_pad(local);
>> +	if (!remote) {
>> +		v4l2_warn(sd, "No link between isp and sensor\n");
>> +		return NULL;
>> +	}
>> +
>> +	sensor_me = media_entity_remote_pad(local)->entity;
>> +	return media_entity_to_v4l2_subdev(sensor_me);
>> +}
>> +
>> +static struct rkisp1_sensor *sd_to_sensor(struct rkisp1_device *dev,
>> +					       struct v4l2_subdev *sd)
> 
> Indentation.
> 
>> +{
>> +	struct rkisp1_sensor *sensor;
>> +
>> +	list_for_each_entry(sensor, &dev->sensors, list)
>> +		if (sensor->sd == sd)
>> +			return sensor;
>> +
>> +	return NULL;
>> +}
>> +
>> +/****************  register operations ****************/
>> +
>> +/*
>> + * Image Stabilization.
>> + * This should only be called when configuring CIF
>> + * or at the frame end interrupt
>> + */
>> +static void rkisp1_config_ism(struct rkisp1_device *dev)
>> +{
>> +	void __iomem *base = dev->base_addr;
>> +	struct v4l2_rect *out_crop = &dev->isp_sdev.out_crop;
>> +	u32 val;
>> +
>> +	writel(0, base + CIF_ISP_IS_RECENTER);
>> +	writel(0, base + CIF_ISP_IS_MAX_DX);
>> +	writel(0, base + CIF_ISP_IS_MAX_DY);
>> +	writel(0, base + CIF_ISP_IS_DISPLACE);
>> +	writel(out_crop->left, base + CIF_ISP_IS_H_OFFS);
>> +	writel(out_crop->top, base + CIF_ISP_IS_V_OFFS);
>> +	writel(out_crop->width, base + CIF_ISP_IS_H_SIZE);
>> +	writel(out_crop->height, base + CIF_ISP_IS_V_SIZE);
>> +
>> +	/* IS(Image Stabilization) is always on, working as output crop */
>> +	writel(1, base + CIF_ISP_IS_CTRL);
>> +	val = readl(base + CIF_ISP_CTRL);
>> +	val |= CIF_ISP_CTRL_ISP_CFG_UPD;
>> +	writel(val, base + CIF_ISP_CTRL);
>> +}
>> +
>> +/*
>> + * configure isp blocks with input format, size......
>> + */
>> +static int rkisp1_config_isp(struct rkisp1_device *dev)
>> +{
>> +	u32 isp_ctrl = 0, irq_mask = 0, acq_mult = 0, signal = 0;
>> +	struct v4l2_rect *out_crop, *in_crop;
>> +	void __iomem *base = dev->base_addr;
>> +	struct v4l2_mbus_framefmt *in_frm;
>> +	struct ispsd_out_fmt *out_fmt;
>> +	struct rkisp1_sensor *sensor;
>> +	struct ispsd_in_fmt *in_fmt;
>> +
>> +	sensor = dev->active_sensor;
>> +	in_frm = &dev->isp_sdev.in_frm;
>> +	in_fmt = &dev->isp_sdev.in_fmt;
>> +	out_fmt = &dev->isp_sdev.out_fmt;
>> +	out_crop = &dev->isp_sdev.out_crop;
>> +	in_crop = &dev->isp_sdev.in_crop;
>> +
>> +	if (in_fmt->fmt_type == FMT_BAYER) {
>> +		acq_mult = 1;
>> +		if (out_fmt->fmt_type == FMT_BAYER) {
>> +			if (sensor->mbus.type == V4L2_MBUS_BT656)
>> +				isp_ctrl =
>> +					CIF_ISP_CTRL_ISP_MODE_RAW_PICT_ITU656;
>> +			else
>> +				isp_ctrl =
>> +					CIF_ISP_CTRL_ISP_MODE_RAW_PICT;
>> +		} else {
>> +			writel(CIF_ISP_DEMOSAIC_TH(0xc),
>> +			       base + CIF_ISP_DEMOSAIC);
>> +
>> +			if (sensor->mbus.type == V4L2_MBUS_BT656)
>> +				isp_ctrl = CIF_ISP_CTRL_ISP_MODE_BAYER_ITU656;
>> +			else
>> +				isp_ctrl = CIF_ISP_CTRL_ISP_MODE_BAYER_ITU601;
>> +		}
>> +	} else if (in_fmt->fmt_type == FMT_YUV) {
>> +		acq_mult = 2;
>> +		if (sensor->mbus.type == V4L2_MBUS_CSI2_DPHY) {
>> +			isp_ctrl = CIF_ISP_CTRL_ISP_MODE_ITU601;
>> +		} else {
>> +			if (sensor->mbus.type == V4L2_MBUS_BT656)
>> +				isp_ctrl = CIF_ISP_CTRL_ISP_MODE_ITU656;
>> +			else
>> +				isp_ctrl = CIF_ISP_CTRL_ISP_MODE_ITU601;
>> +
>> +		}
>> +
>> +		irq_mask |= CIF_ISP_DATA_LOSS;
>> +	}
>> +
>> +	/* Set up input acquisition properties */
>> +	if (sensor->mbus.type == V4L2_MBUS_BT656 ||
>> +	    sensor->mbus.type == V4L2_MBUS_PARALLEL) {
>> +		if (sensor->mbus.flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
>> +			signal = CIF_ISP_ACQ_PROP_POS_EDGE;
>> +	}
>> +
>> +	if (sensor->mbus.type == V4L2_MBUS_PARALLEL) {
>> +		if (sensor->mbus.flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
>> +			signal |= CIF_ISP_ACQ_PROP_VSYNC_LOW;
>> +
>> +		if (sensor->mbus.flags & V4L2_MBUS_HSYNC_ACTIVE_LOW)
>> +			signal |= CIF_ISP_ACQ_PROP_HSYNC_LOW;
>> +	}
>> +
>> +	writel(isp_ctrl, base + CIF_ISP_CTRL);
>> +	writel(signal | in_fmt->yuv_seq |
>> +	       CIF_ISP_ACQ_PROP_BAYER_PAT(in_fmt->bayer_pat) |
>> +	       CIF_ISP_ACQ_PROP_FIELD_SEL_ALL, base + CIF_ISP_ACQ_PROP);
>> +	writel(0, base + CIF_ISP_ACQ_NR_FRAMES);
>> +
>> +	/* Acquisition Size */
>> +	writel(0, base + CIF_ISP_ACQ_H_OFFS);
>> +	writel(0, base + CIF_ISP_ACQ_V_OFFS);
>> +	writel(acq_mult * in_frm->width, base + CIF_ISP_ACQ_H_SIZE);
>> +	writel(in_frm->height, base + CIF_ISP_ACQ_V_SIZE);
>> +
>> +	/* ISP Out Area */
>> +	writel(in_crop->left, base + CIF_ISP_OUT_H_OFFS);
>> +	writel(in_crop->top, base + CIF_ISP_OUT_V_OFFS);
>> +	writel(in_crop->width, base + CIF_ISP_OUT_H_SIZE);
>> +	writel(in_crop->height, base + CIF_ISP_OUT_V_SIZE);
>> +
>> +	/* interrupt mask */
>> +	irq_mask |= CIF_ISP_FRAME | CIF_ISP_V_START | CIF_ISP_PIC_SIZE_ERROR |
>> +		    CIF_ISP_FRAME_IN;
>> +	writel(irq_mask, base + CIF_ISP_IMSC);
>> +
>> +	if (out_fmt->fmt_type == FMT_BAYER)
>> +		rkisp1_params_disable_isp(&dev->params_vdev);
>> +	else
>> +		rkisp1_params_configure_isp(&dev->params_vdev, in_fmt,
>> +					    dev->isp_sdev.quantization);
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_config_dvp(struct rkisp1_device *dev)
>> +{
>> +	struct ispsd_in_fmt *in_fmt = &dev->isp_sdev.in_fmt;
>> +	void __iomem *base = dev->base_addr;
>> +	u32 val, input_sel;
>> +
>> +	switch (in_fmt->bus_width) {
>> +	case 8:
>> +		input_sel = CIF_ISP_ACQ_PROP_IN_SEL_8B_ZERO;
>> +		break;
>> +	case 10:
>> +		input_sel = CIF_ISP_ACQ_PROP_IN_SEL_10B_ZERO;
>> +		break;
>> +	case 12:
>> +		input_sel = CIF_ISP_ACQ_PROP_IN_SEL_12B;
>> +		break;
>> +	default:
>> +		v4l2_err(&dev->v4l2_dev, "Invalid bus width\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	val = readl(base + CIF_ISP_ACQ_PROP);
>> +	writel(val | input_sel, base + CIF_ISP_ACQ_PROP);
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_config_mipi(struct rkisp1_device *dev)
>> +{
>> +	struct ispsd_in_fmt *in_fmt = &dev->isp_sdev.in_fmt;
>> +	struct rkisp1_sensor *sensor = dev->active_sensor;
>> +	void __iomem *base = dev->base_addr;
>> +	unsigned int lanes;
>> +	u32 mipi_ctrl;
>> +
>> +	/*
>> +	 * sensor->mbus is set in isp or d-phy notifier_bound function
>> +	 */
>> +	switch (sensor->mbus.flags & V4L2_MBUS_CSI2_LANES) {
>> +	case V4L2_MBUS_CSI2_4_LANE:
>> +		lanes = 4;
>> +		break;
>> +	case V4L2_MBUS_CSI2_3_LANE:
>> +		lanes = 3;
>> +		break;
>> +	case V4L2_MBUS_CSI2_2_LANE:
>> +		lanes = 2;
>> +		break;
>> +	case V4L2_MBUS_CSI2_1_LANE:
>> +		lanes = 1;
>> +		break;
>> +	default:
>> +		return -EINVAL;
>> +	}
>> +
>> +	mipi_ctrl = CIF_MIPI_CTRL_NUM_LANES(lanes - 1) |
>> +		    CIF_MIPI_CTRL_SHUTDOWNLANES(0xf) |
>> +		    CIF_MIPI_CTRL_ERR_SOT_SYNC_HS_SKIP |
>> +		    CIF_MIPI_CTRL_CLOCKLANE_ENA;
>> +
>> +	writel(mipi_ctrl, base + CIF_MIPI_CTRL);
>> +
>> +	/* Configure Data Type and Virtual Channel */
>> +	writel(CIF_MIPI_DATA_SEL_DT(in_fmt->mipi_dt) | CIF_MIPI_DATA_SEL_VC(0),
>> +	       base + CIF_MIPI_IMG_DATA_SEL);
>> +
>> +	/* Clear MIPI interrupts */
>> +	writel(~0, base + CIF_MIPI_ICR);
>> +	/*
>> +	 * Disable CIF_MIPI_ERR_DPHY interrupt here temporary for
>> +	 * isp bus may be dead when switch isp.
>> +	 */
>> +	writel(CIF_MIPI_FRAME_END | CIF_MIPI_ERR_CSI | CIF_MIPI_ERR_DPHY |
>> +	       CIF_MIPI_SYNC_FIFO_OVFLW(0x03) | CIF_MIPI_ADD_DATA_OVFLW,
>> +	       base + CIF_MIPI_IMSC);
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev, "\n  MIPI_CTRL 0x%08x\n"
>> +		 "  MIPI_IMG_DATA_SEL 0x%08x\n"
>> +		 "  MIPI_STATUS 0x%08x\n"
>> +		 "  MIPI_IMSC 0x%08x\n",
>> +		 readl(base + CIF_MIPI_CTRL),
>> +		 readl(base + CIF_MIPI_IMG_DATA_SEL),
>> +		 readl(base + CIF_MIPI_STATUS),
>> +		 readl(base + CIF_MIPI_IMSC));
>> +
>> +	return 0;
>> +}
>> +
>> +/* Configure MUX */
>> +static int rkisp1_config_path(struct rkisp1_device *dev)
>> +{
>> +	struct rkisp1_sensor *sensor = dev->active_sensor;
>> +	u32 dpcl = readl(dev->base_addr + CIF_VI_DPCL);
>> +	int ret = 0;
>> +
>> +	if (sensor->mbus.type == V4L2_MBUS_BT656 ||
>> +	    sensor->mbus.type == V4L2_MBUS_PARALLEL) {
>> +		ret = rkisp1_config_dvp(dev);
>> +		dpcl |= CIF_VI_DPCL_IF_SEL_PARALLEL;
>> +	} else if (sensor->mbus.type == V4L2_MBUS_CSI2_DPHY) {
>> +		ret = rkisp1_config_mipi(dev);
>> +		dpcl |= CIF_VI_DPCL_IF_SEL_MIPI;
>> +	}
>> +
>> +	writel(dpcl, dev->base_addr + CIF_VI_DPCL);
>> +
>> +	return ret;
>> +}
>> +
>> +/* Hareware configure Entry */
>> +static int rkisp1_config_cif(struct rkisp1_device *dev)
>> +{
>> +	u32 cif_id;
>> +	int ret;
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		 "SP streaming = %d, MP streaming = %d\n",
>> +		 dev->stream[RKISP1_STREAM_SP].streaming,
>> +		 dev->stream[RKISP1_STREAM_MP].streaming);
>> +
>> +	cif_id = readl(dev->base_addr + CIF_VI_ID);
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev, "CIF_ID 0x%08x\n", cif_id);
>> +
>> +	ret = rkisp1_config_isp(dev);
>> +	if (ret < 0)
>> +		return ret;
>> +	ret = rkisp1_config_path(dev);
>> +	if (ret < 0)
>> +		return ret;
>> +	rkisp1_config_ism(dev);
>> +
>> +	return 0;
>> +}
>> +
>> +/* Mess register operations to stop isp */
>> +static int rkisp1_isp_stop(struct rkisp1_device *dev)
>> +{
>> +	void __iomem *base = dev->base_addr;
>> +	u32 val;
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		 "SP streaming = %d, MP streaming = %d\n",
>> +		 dev->stream[RKISP1_STREAM_SP].streaming,
>> +		 dev->stream[RKISP1_STREAM_MP].streaming);
>> +
>> +	/*
>> +	 * ISP(mi) stop in mi frame end -> Stop ISP(mipi) ->
>> +	 * Stop ISP(isp) ->wait for ISP isp off
>> +	 */
>> +	/* stop and clear MI, MIPI, and ISP interrupts */
>> +	writel(0, base + CIF_MIPI_IMSC);
>> +	writel(~0, base + CIF_MIPI_ICR);
>> +
>> +	writel(0, base + CIF_ISP_IMSC);
>> +	writel(~0, base + CIF_ISP_ICR);
>> +
>> +	writel(0, base + CIF_MI_IMSC);
>> +	writel(~0, base + CIF_MI_ICR);
>> +	val = readl(base + CIF_MIPI_CTRL);
>> +	writel(val & (~CIF_MIPI_CTRL_OUTPUT_ENA), base + CIF_MIPI_CTRL);
>> +	/* stop ISP */
>> +	val = readl(base + CIF_ISP_CTRL);
>> +	val &= ~(CIF_ISP_CTRL_ISP_INFORM_ENABLE | CIF_ISP_CTRL_ISP_ENABLE);
>> +	writel(val, base + CIF_ISP_CTRL);
>> +
>> +	val = readl(base + CIF_ISP_CTRL);
>> +	writel(val | CIF_ISP_CTRL_ISP_CFG_UPD, base + CIF_ISP_CTRL);
>> +
>> +	readx_poll_timeout(readl, base + CIF_ISP_RIS,
>> +			   val, val & CIF_ISP_OFF, 20, 100);
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		"streaming(MP:%d, SP:%d), MI_CTRL:%x, ISP_CTRL:%x, MIPI_CTRL:%x\n",
>> +		 dev->stream[RKISP1_STREAM_SP].streaming,
>> +		 dev->stream[RKISP1_STREAM_MP].streaming,
>> +		 readl(base + CIF_MI_CTRL),
>> +		 readl(base + CIF_ISP_CTRL),
>> +		 readl(base + CIF_MIPI_CTRL));
>> +
>> +	writel(CIF_IRCL_MIPI_SW_RST | CIF_IRCL_ISP_SW_RST, base + CIF_IRCL);
>> +	writel(0x0, base + CIF_IRCL);
>> +
>> +	return 0;
>> +}
>> +
>> +/* Mess register operations to start isp */
>> +static int rkisp1_isp_start(struct rkisp1_device *dev)
>> +{
>> +	struct rkisp1_sensor *sensor = dev->active_sensor;
>> +	void __iomem *base = dev->base_addr;
>> +	u32 val;
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		 "SP streaming = %d, MP streaming = %d\n",
>> +		 dev->stream[RKISP1_STREAM_SP].streaming,
>> +		 dev->stream[RKISP1_STREAM_MP].streaming);
>> +
>> +	/* Activate MIPI */
>> +	if (sensor->mbus.type == V4L2_MBUS_CSI2_DPHY) {
>> +		val = readl(base + CIF_MIPI_CTRL);
>> +		writel(val | CIF_MIPI_CTRL_OUTPUT_ENA, base + CIF_MIPI_CTRL);
>> +	}
>> +	/* Activate ISP */
>> +	val = readl(base + CIF_ISP_CTRL);
>> +	val |= CIF_ISP_CTRL_ISP_CFG_UPD | CIF_ISP_CTRL_ISP_ENABLE |
>> +	       CIF_ISP_CTRL_ISP_INFORM_ENABLE;
>> +	writel(val, base + CIF_ISP_CTRL);
>> +
>> +	/* XXX: Is the 1000us too long?
>> +	 * CIF spec says to wait for sufficient time after enabling
>> +	 * the MIPI interface and before starting the sensor output.
>> +	 */
>> +	usleep_range(1000, 1200);
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		 "SP streaming = %d, MP streaming = %d MI_CTRL 0x%08x\n"
>> +		 "  ISP_CTRL 0x%08x MIPI_CTRL 0x%08x\n",
>> +		 dev->stream[RKISP1_STREAM_SP].streaming,
>> +		 dev->stream[RKISP1_STREAM_MP].streaming,
>> +		 readl(base + CIF_MI_CTRL),
>> +		 readl(base + CIF_ISP_CTRL),
>> +		 readl(base + CIF_MIPI_CTRL));
>> +
>> +	return 0;
>> +}
>> +
>> +static void rkisp1_config_clk(struct rkisp1_device *dev)
>> +{
>> +	u32 val = CIF_ICCL_ISP_CLK | CIF_ICCL_CP_CLK | CIF_ICCL_MRSZ_CLK |
>> +		  CIF_ICCL_SRSZ_CLK | CIF_ICCL_JPEG_CLK | CIF_ICCL_MI_CLK |
>> +		  CIF_ICCL_IE_CLK | CIF_ICCL_MIPI_CLK | CIF_ICCL_DCROP_CLK;
>> +
>> +	writel(val, dev->base_addr + CIF_ICCL);
>> +}
>> +
>> +/***************************** isp sub-devs *******************************/
>> +
>> +static const struct ispsd_in_fmt rkisp1_isp_input_formats[] = {
>> +	{
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW10,
>> +		.bayer_pat	= RAW_BGGR,
>> +		.bus_width	= 10,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW10,
>> +		.bayer_pat	= RAW_RGGB,
>> +		.bus_width	= 10,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW10,
>> +		.bayer_pat	= RAW_GBRG,
>> +		.bus_width	= 10,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW10,
>> +		.bayer_pat	= RAW_GRBG,
>> +		.bus_width	= 10,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW12,
>> +		.bayer_pat	= RAW_RGGB,
>> +		.bus_width	= 12,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW12,
>> +		.bayer_pat	= RAW_BGGR,
>> +		.bus_width	= 12,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW12,
>> +		.bayer_pat	= RAW_GBRG,
>> +		.bus_width	= 12,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW12,
>> +		.bayer_pat	= RAW_GRBG,
>> +		.bus_width	= 12,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW8,
>> +		.bayer_pat	= RAW_RGGB,
>> +		.bus_width	= 8,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW8,
>> +		.bayer_pat	= RAW_BGGR,
>> +		.bus_width	= 8,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW8,
>> +		.bayer_pat	= RAW_GBRG,
>> +		.bus_width	= 8,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +		.mipi_dt	= CIF_CSI2_DT_RAW8,
>> +		.bayer_pat	= RAW_GRBG,
>> +		.bus_width	= 8,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_YUYV8_1X16,
>> +		.fmt_type	= FMT_YUV,
>> +		.mipi_dt	= CIF_CSI2_DT_YUV422_8b,
>> +		.yuv_seq	= CIF_ISP_ACQ_PROP_YCBYCR,
>> +		.bus_width	= 16,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_YVYU8_1X16,
>> +		.fmt_type	= FMT_YUV,
>> +		.mipi_dt	= CIF_CSI2_DT_YUV422_8b,
>> +		.yuv_seq	= CIF_ISP_ACQ_PROP_YCRYCB,
>> +		.bus_width	= 16,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_UYVY8_1X16,
>> +		.fmt_type	= FMT_YUV,
>> +		.mipi_dt	= CIF_CSI2_DT_YUV422_8b,
>> +		.yuv_seq	= CIF_ISP_ACQ_PROP_CBYCRY,
>> +		.bus_width	= 16,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_VYUY8_1X16,
>> +		.fmt_type	= FMT_YUV,
>> +		.mipi_dt	= CIF_CSI2_DT_YUV422_8b,
>> +		.yuv_seq	= CIF_ISP_ACQ_PROP_CRYCBY,
>> +		.bus_width	= 16,
>> +	},
>> +};
>> +
>> +static const struct ispsd_out_fmt rkisp1_isp_output_formats[] = {
>> +	{
>> +		.mbus_code	= MEDIA_BUS_FMT_YUYV8_2X8,
>> +		.fmt_type	= FMT_YUV,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG12_1X12,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG10_1X10,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SRGGB8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SBGGR8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGBRG8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +	}, {
>> +		.mbus_code	= MEDIA_BUS_FMT_SGRBG8_1X8,
>> +		.fmt_type	= FMT_BAYER,
>> +	},
>> +};
>> +
>> +static const struct ispsd_in_fmt *find_in_fmt(u32 mbus_code)
>> +{
>> +	unsigned int i, array_size = ARRAY_SIZE(rkisp1_isp_input_formats);
> 
> I think it'd be nicer to just use ARRAY_SIZE(...) in the condition. Same
> below.
> 
>> +	const struct ispsd_in_fmt *fmt;
>> +
>> +	for (i = 0; i < array_size; i++) {
>> +		fmt = &rkisp1_isp_input_formats[i];
>> +		if (fmt->mbus_code == mbus_code)
>> +			return fmt;
>> +	}
>> +
>> +	return NULL;
>> +}
>> +
>> +static const struct ispsd_out_fmt *find_out_fmt(u32 mbus_code)
>> +{
>> +	unsigned int i, array_size = ARRAY_SIZE(rkisp1_isp_output_formats);
>> +	const struct ispsd_out_fmt *fmt;
>> +
>> +	for (i = 0; i < array_size; i++) {
>> +		fmt = &rkisp1_isp_output_formats[i];
>> +		if (fmt->mbus_code == mbus_code)
>> +			return fmt;
>> +	}
>> +
>> +	return NULL;
>> +}
>> +
>> +static int rkisp1_isp_sd_enum_mbus_code(struct v4l2_subdev *sd,
>> +					struct v4l2_subdev_pad_config *cfg,
>> +					struct v4l2_subdev_mbus_code_enum *code)
>> +{
>> +	unsigned int i = code->index;
>> +
>> +	if ((code->pad != RKISP1_ISP_PAD_SINK) &&
>> +	    (code->pad != RKISP1_ISP_PAD_SOURCE_PATH)) {
>> +		if (i > 0)
>> +			return -EINVAL;
>> +		code->code = MEDIA_BUS_FMT_FIXED;
>> +		return 0;
>> +	}
>> +
>> +	if (code->pad == RKISP1_ISP_PAD_SINK) {
>> +		if (i >= ARRAY_SIZE(rkisp1_isp_input_formats))
>> +			return -EINVAL;
>> +		code->code = rkisp1_isp_input_formats[i].mbus_code;
>> +	} else {
>> +		if (i >= ARRAY_SIZE(rkisp1_isp_output_formats))
>> +			return -EINVAL;
>> +		code->code = rkisp1_isp_output_formats[i].mbus_code;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_isp_sd_init_config(struct v4l2_subdev *sd,
>> +				     struct v4l2_subdev_pad_config *cfg)
>> +{
>> +	struct v4l2_rect *mf_in_crop, *mf_out_crop;
>> +	struct v4l2_mbus_framefmt *mf_in, *mf_out;
>> +
>> +	mf_in = v4l2_subdev_get_try_format(sd, cfg, RKISP1_ISP_PAD_SINK);
>> +	mf_in->width = RKISP1_DEFAULT_WIDTH;
>> +	mf_in->height = RKISP1_DEFAULT_HEIGHT;
>> +	mf_in->field = V4L2_FIELD_NONE;
>> +	mf_in->code = rkisp1_isp_input_formats[0].mbus_code;
>> +
>> +	mf_in_crop = v4l2_subdev_get_try_crop(sd, cfg, RKISP1_ISP_PAD_SINK);
>> +	mf_in_crop->width = RKISP1_DEFAULT_WIDTH;
>> +	mf_in_crop->height = RKISP1_DEFAULT_HEIGHT;
>> +	mf_in_crop->left = 0;
>> +	mf_in_crop->top = 0;
>> +
>> +	mf_out = v4l2_subdev_get_try_format(sd, cfg,
>> +					    RKISP1_ISP_PAD_SOURCE_PATH);
>> +	*mf_out = *mf_in;
>> +	mf_out->code = rkisp1_isp_output_formats[0].mbus_code;
>> +	mf_out->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> +
>> +	mf_out_crop = v4l2_subdev_get_try_crop(sd, cfg,
>> +					       RKISP1_ISP_PAD_SOURCE_PATH);
>> +	*mf_out_crop = *mf_in_crop;
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_isp_sd_get_fmt(struct v4l2_subdev *sd,
>> +				 struct v4l2_subdev_pad_config *cfg,
>> +				 struct v4l2_subdev_format *fmt)
>> +{
>> +	struct rkisp1_isp_subdev *isp_sd = sd_to_isp_sd(sd);
>> +	struct v4l2_mbus_framefmt *mf = &fmt->format;
>> +
>> +	if ((fmt->pad != RKISP1_ISP_PAD_SINK) &&
>> +	    (fmt->pad != RKISP1_ISP_PAD_SOURCE_PATH)) {
>> +		fmt->format.code = MEDIA_BUS_FMT_FIXED;
>> +		/*
>> +		 * NOTE: setting a format here doesn't make much sense
>> +		 * but v4l2-compliance complains
>> +		 */
>> +		fmt->format.width = RKISP1_DEFAULT_WIDTH;
>> +		fmt->format.height = RKISP1_DEFAULT_HEIGHT;
>> +		fmt->format.field = V4L2_FIELD_NONE;
>> +		return 0;
>> +	}
>> +
>> +	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
>> +		mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
>> +		fmt->format = *mf;
>> +		return 0;
>> +	}
>> +
>> +	if (fmt->pad == RKISP1_ISP_PAD_SINK) {
>> +		*mf = isp_sd->in_frm;
>> +	} else if (fmt->pad == RKISP1_ISP_PAD_SOURCE_PATH) {
>> +		/* format of source pad */
>> +		*mf = isp_sd->in_frm;
>> +		mf->code = isp_sd->out_fmt.mbus_code;
>> +		/* window size of source pad */
>> +		mf->width = isp_sd->out_crop.width;
>> +		mf->height = isp_sd->out_crop.height;
>> +		mf->quantization = isp_sd->quantization;
>> +	}
>> +	mf->field = V4L2_FIELD_NONE;
>> +
>> +	return 0;
>> +}
>> +
>> +static void rkisp1_isp_sd_try_fmt(struct v4l2_subdev *sd,
>> +				  unsigned int pad,
>> +				  struct v4l2_mbus_framefmt *fmt)
>> +{
>> +	struct rkisp1_device *isp_dev = sd_to_isp_dev(sd);
>> +	struct rkisp1_isp_subdev *isp_sd = &isp_dev->isp_sdev;
>> +	const struct ispsd_out_fmt *out_fmt;
>> +	const struct ispsd_in_fmt *in_fmt;
>> +
>> +	switch (pad) {
>> +	case RKISP1_ISP_PAD_SINK:
>> +		in_fmt = find_in_fmt(fmt->code);
>> +		if (in_fmt)
>> +			fmt->code = in_fmt->mbus_code;
>> +		else
>> +			fmt->code = MEDIA_BUS_FMT_SRGGB10_1X10;
>> +		fmt->width  = clamp_t(u32, fmt->width, CIF_ISP_INPUT_W_MIN,
>> +				      CIF_ISP_INPUT_W_MAX);
>> +		fmt->height = clamp_t(u32, fmt->height, CIF_ISP_INPUT_H_MIN,
>> +				      CIF_ISP_INPUT_H_MAX);
>> +		break;
>> +	case RKISP1_ISP_PAD_SOURCE_PATH:
>> +		out_fmt = find_out_fmt(fmt->code);
>> +		if (out_fmt)
>> +			fmt->code = out_fmt->mbus_code;
>> +		else
>> +			fmt->code = rkisp1_isp_output_formats[0].mbus_code;
>> +		/* window size is set in s_selection */
>> +		fmt->width  = isp_sd->out_crop.width;
>> +		fmt->height = isp_sd->out_crop.height;
>> +		/* full range by default */
>> +		if (!fmt->quantization)
>> +			fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> +		break;
>> +	}
>> +
>> +	fmt->field = V4L2_FIELD_NONE;
>> +}
>> +
>> +static int rkisp1_isp_sd_set_fmt(struct v4l2_subdev *sd,
>> +				 struct v4l2_subdev_pad_config *cfg,
>> +				 struct v4l2_subdev_format *fmt)
>> +{
>> +	struct rkisp1_device *isp_dev = sd_to_isp_dev(sd);
>> +	struct rkisp1_isp_subdev *isp_sd = &isp_dev->isp_sdev;
>> +	struct v4l2_mbus_framefmt *mf = &fmt->format;
>> +
> 
> Note that for sub-device nodes, the driver is itself responsible for
> serialising the access to its data structures.

But looking at subdev_do_ioctl_lock(), it seems that it serializes the
ioctl calls for subdevs, no? Or I'm misunderstanding something (which is
most probably) ?

> 
>> +	if ((fmt->pad != RKISP1_ISP_PAD_SINK) &&
>> +	    (fmt->pad != RKISP1_ISP_PAD_SOURCE_PATH))
>> +		return rkisp1_isp_sd_get_fmt(sd, cfg, fmt);
>> +
>> +	rkisp1_isp_sd_try_fmt(sd, fmt->pad, mf);
>> +
>> +	if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
>> +		struct v4l2_mbus_framefmt *try_mf;
>> +
>> +		try_mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
>> +		*try_mf = *mf;
>> +		return 0;
>> +	}
>> +
>> +	if (fmt->pad == RKISP1_ISP_PAD_SINK) {
>> +		const struct ispsd_in_fmt *in_fmt;
>> +
>> +		in_fmt = find_in_fmt(mf->code);
>> +		isp_sd->in_fmt = *in_fmt;
>> +		isp_sd->in_frm = *mf;
>> +	} else if (fmt->pad == RKISP1_ISP_PAD_SOURCE_PATH) {
>> +		const struct ispsd_out_fmt *out_fmt;
>> +
>> +		/* Ignore width/height */
>> +		out_fmt = find_out_fmt(mf->code);
>> +		isp_sd->out_fmt = *out_fmt;
>> +		/*
>> +		 * It is quantization for output,
>> +		 * isp use bt601 limit-range in internal
>> +		 */
>> +		isp_sd->quantization = mf->quantization;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static void rkisp1_isp_sd_try_crop(struct v4l2_subdev *sd,
>> +				  struct v4l2_subdev_pad_config *cfg,
>> +				  struct v4l2_subdev_selection *sel)
>> +{
>> +	struct rkisp1_isp_subdev *isp_sd = sd_to_isp_sd(sd);
>> +	struct v4l2_mbus_framefmt in_frm = isp_sd->in_frm;
>> +	struct v4l2_rect in_crop = isp_sd->in_crop;
>> +	struct v4l2_rect *input = &sel->r;
>> +
>> +	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
>> +		in_frm = *v4l2_subdev_get_try_format(sd, cfg,
>> +						     RKISP1_ISP_PAD_SINK);
>> +		in_crop = *v4l2_subdev_get_try_crop(sd, cfg,
>> +						    RKISP1_ISP_PAD_SINK);
>> +	}
>> +
>> +	input->left = ALIGN(input->left, 2);
>> +	input->width = ALIGN(input->width, 2);
>> +
>> +	if (sel->pad == RKISP1_ISP_PAD_SINK) {
>> +		input->left = clamp_t(u32, input->left, 0, in_frm.width);
>> +		input->top = clamp_t(u32, input->top, 0, in_frm.height);
>> +		input->width = clamp_t(u32, input->width, CIF_ISP_INPUT_W_MIN,
>> +				       in_frm.width - input->left);
>> +		input->height = clamp_t(u32, input->height,
>> +					CIF_ISP_INPUT_H_MIN,
>> +					in_frm.height - input->top);
>> +	} else if (sel->pad == RKISP1_ISP_PAD_SOURCE_PATH) {
>> +		input->left = clamp_t(u32, input->left, 0, in_crop.width);
>> +		input->top = clamp_t(u32, input->top, 0, in_crop.height);
>> +		input->width = clamp_t(u32, input->width, CIF_ISP_OUTPUT_W_MIN,
>> +				       in_crop.width - input->left);
>> +		input->height = clamp_t(u32, input->height,
>> +					CIF_ISP_OUTPUT_H_MIN,
>> +					in_crop.height - input->top);
>> +	}
>> +}
>> +
>> +static int rkisp1_isp_sd_get_selection(struct v4l2_subdev *sd,
>> +				       struct v4l2_subdev_pad_config *cfg,
>> +				       struct v4l2_subdev_selection *sel)
>> +{
>> +	struct rkisp1_isp_subdev *isp_sd = sd_to_isp_sd(sd);
>> +	struct v4l2_mbus_framefmt *frm;
>> +	struct v4l2_rect *rect;
>> +
>> +	if (sel->pad != RKISP1_ISP_PAD_SOURCE_PATH &&
>> +	    sel->pad != RKISP1_ISP_PAD_SINK)
>> +		return -EINVAL;
>> +
>> +	switch (sel->target) {
>> +	case V4L2_SEL_TGT_CROP_BOUNDS:
>> +		if (sel->pad == RKISP1_ISP_PAD_SINK) {
>> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
>> +				frm = v4l2_subdev_get_try_format(sd, cfg,
>> +								 sel->pad);
>> +			else
>> +				frm = &isp_sd->in_frm;
>> +
>> +			sel->r.height = frm->height;
>> +			sel->r.width = frm->width;
>> +			sel->r.left = 0;
>> +			sel->r.top = 0;
>> +		} else {
>> +			if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
>> +				rect = v4l2_subdev_get_try_crop(sd, cfg,
>> +							RKISP1_ISP_PAD_SINK);
>> +			else
>> +				rect = &isp_sd->in_crop;
>> +			sel->r = *rect;
>> +		}
>> +		break;
>> +	case V4L2_SEL_TGT_CROP:
>> +		if (sel->which == V4L2_SUBDEV_FORMAT_TRY)
>> +			rect = v4l2_subdev_get_try_crop(sd, cfg, sel->pad);
>> +		else if (sel->pad == RKISP1_ISP_PAD_SINK)
>> +			rect = &isp_sd->in_crop;
>> +		else
>> +			rect = &isp_sd->out_crop;
>> +		sel->r = *rect;
>> +		break;
>> +	default:
>> +		return -EINVAL;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_isp_sd_set_selection(struct v4l2_subdev *sd,
>> +				       struct v4l2_subdev_pad_config *cfg,
>> +				       struct v4l2_subdev_selection *sel)
>> +{
>> +	struct rkisp1_isp_subdev *isp_sd = sd_to_isp_sd(sd);
>> +	struct rkisp1_device *dev = sd_to_isp_dev(sd);
>> +
>> +	if (sel->pad != RKISP1_ISP_PAD_SOURCE_PATH &&
>> +	    sel->pad != RKISP1_ISP_PAD_SINK)
>> +		return -EINVAL;
>> +	if (sel->target != V4L2_SEL_TGT_CROP)
>> +		return -EINVAL;
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &dev->v4l2_dev,
>> +		 "%s: pad: %d sel(%d,%d)/%dx%d\n", __func__, sel->pad,
>> +		 sel->r.left, sel->r.top, sel->r.width, sel->r.height);
>> +	rkisp1_isp_sd_try_crop(sd, cfg, sel);
>> +
>> +	if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
>> +		struct v4l2_rect *try_sel =
>> +			v4l2_subdev_get_try_crop(sd, cfg, sel->pad);
>> +
>> +		*try_sel = sel->r;
>> +		return 0;
>> +	}
>> +
>> +	if (sel->pad == RKISP1_ISP_PAD_SINK)
>> +		isp_sd->in_crop = sel->r;
>> +	else
>> +		isp_sd->out_crop = sel->r;
>> +
>> +	return 0;
>> +}
>> +
>> +static int mipi_csi2_s_stream_start(struct rkisp1_isp_subdev *isp_sd,
>> +				    struct rkisp1_sensor *sensor)
>> +{
>> +	union phy_configure_opts opts = { 0 };
>> +	struct phy_configure_opts_mipi_dphy *cfg = &opts.mipi_dphy;
>> +	struct v4l2_ctrl *pixel_rate;
>> +	s64 pixel_clock;
>> +
>> +	pixel_rate = v4l2_ctrl_find(sensor->sd->ctrl_handler,
>> +				    V4L2_CID_PIXEL_RATE);
>> +	if (!pixel_rate) {
>> +		v4l2_warn(sensor->sd, "No pixel rate control in subdev\n");
>> +		return -EPIPE;
>> +	}
>> +
>> +	pixel_clock = v4l2_ctrl_g_ctrl_int64(pixel_rate);
>> +	if (!pixel_clock) {
>> +		v4l2_err(sensor->sd, "Invalid pixel rate value\n");
>> +		return -EINVAL;
>> +	}
>> +
>> +	phy_mipi_dphy_get_default_config(pixel_clock, isp_sd->in_fmt.bus_width,
>> +					 sensor->lanes, cfg);
>> +	phy_set_mode(sensor->dphy, PHY_MODE_MIPI_DPHY);
>> +	phy_configure(sensor->dphy, &opts);
>> +	phy_power_on(sensor->dphy);
>> +
>> +	return 0;
>> +}
>> +
>> +static void mipi_csi2_s_stream_stop(struct rkisp1_sensor *sensor)
>> +{
>> +	phy_power_off(sensor->dphy);
>> +}
>> +
>> +static int rkisp1_isp_sd_s_stream(struct v4l2_subdev *sd, int on)
>> +{
>> +	struct rkisp1_device *isp_dev = sd_to_isp_dev(sd);
>> +	struct v4l2_subdev *sensor_sd;
>> +	int ret = 0;
>> +
>> +	if (!on) {
>> +		ret = rkisp1_isp_stop(isp_dev);
>> +		if (ret < 0)
>> +			return ret;
>> +		mipi_csi2_s_stream_stop(isp_dev->active_sensor);
>> +		return 0;
>> +	}
>> +
>> +	sensor_sd = get_remote_sensor(sd);
>> +	if (!sensor_sd)
>> +		return -ENODEV;
>> +
>> +	isp_dev->active_sensor = sd_to_sensor(isp_dev, sensor_sd);
>> +	if (!isp_dev->active_sensor)
>> +		return -ENODEV;
>> +
>> +	atomic_set(&isp_dev->isp_sdev.frm_sync_seq, 0);
>> +	ret = rkisp1_config_cif(isp_dev);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	/* TODO: support other interfaces */
>> +	if (isp_dev->active_sensor->mbus.type != V4L2_MBUS_CSI2_DPHY)
>> +		return -EINVAL;
>> +
>> +	ret = mipi_csi2_s_stream_start(&isp_dev->isp_sdev,
>> +				       isp_dev->active_sensor);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	ret = rkisp1_isp_start(isp_dev);
>> +	if (ret)
>> +		mipi_csi2_s_stream_stop(isp_dev->active_sensor);
>> +
>> +	return ret;
>> +}
>> +
>> +static int rkisp1_isp_sd_s_power(struct v4l2_subdev *sd, int on)
> 
> If you support runtime PM, you shouldn't implement the s_power op.

Is is ok to completly remove the usage of runtime PM then?
Like this http://ix.io/1RJb ?

tbh I'm not that familar with runtime PM and I'm not sure what is the
difference of it and using s_power op (and Documentation/power/runtime_pm.rst
is not being that helpful tbh).

> 
> You'll still need to call s_power on external subdevs though.
> 
>> +{
>> +	struct rkisp1_device *isp_dev = sd_to_isp_dev(sd);
>> +	int ret;
>> +
>> +	v4l2_dbg(1, rkisp1_debug, &isp_dev->v4l2_dev, "s_power: %d\n", on);
>> +
>> +	if (on) {
>> +		ret = pm_runtime_get_sync(isp_dev->dev);

If this is not ok to remove suport for runtime PM, then where should I put
the call to pm_runtime_get_sync() if not in this s_power op ?

>> +		if (ret < 0)
>> +			return ret;
>> +
>> +		rkisp1_config_clk(isp_dev);
>> +	} else {
>> +		ret = pm_runtime_put(isp_dev->dev);
>> +		if (ret < 0)
>> +			return ret;
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int rkisp1_subdev_link_validate(struct media_link *link)
>> +{
>> +	if (link->source->index == RKISP1_ISP_PAD_SINK_PARAMS)
> 
> Is this test correct? The source is the source end of the link, i.e. the
> video node.

Ah yes, it should be link->sink->index (and not source), thanks for spotting this.

> 
> How about the links that end in a video node?

I thought that the only possibilities were sensor->isp1 and params->isp1 (where params
is an output video node that should be catched by the corrected version of the if
statement above.

Or do you mean another thing?

> 
>> +		return 0;
>> +
>> +	return v4l2_subdev_link_validate(link);
>> +}
>> +
>> +static int rkisp1_subdev_fmt_link_validate(struct v4l2_subdev *sd,
>> +					struct media_link *link,
>> +					struct v4l2_subdev_format *source_fmt,
>> +					struct v4l2_subdev_format *sink_fmt)
>> +{
>> +	if (source_fmt->format.code != sink_fmt->format.code)
>> +		return -EINVAL;

ops, should be -EPIPE

>> +
>> +	/* Crop is available */
>> +	if (source_fmt->format.width < sink_fmt->format.width ||
>> +	    source_fmt->format.height < sink_fmt->format.height)
>> +		return -EINVAL;

-EPIPE

>> +
> 
> Could you use v4l2_subdev_link_validate_default()?

v4l2_subdev_link_validate_default() only allows for an exact width/height match,
but here we allow the sink to be smaller then the source for cropping, no?

Thanks again for your review!
Helen

> 
>> +	return 0;
>> +}
>> +
>> +static void rkisp1_isp_queue_event_sof(struct rkisp1_isp_subdev *isp)
>> +{
>> +	struct v4l2_event event = {
>> +		.type = V4L2_EVENT_FRAME_SYNC,
>> +		.u.frame_sync.frame_sequence =
>> +			atomic_inc_return(&isp->frm_sync_seq) - 1,
>> +	};
>> +	v4l2_event_queue(isp->sd.devnode, &event);
>> +}
>> +
>> +static int rkisp1_isp_sd_subs_evt(struct v4l2_subdev *sd, struct v4l2_fh *fh,
>> +				  struct v4l2_event_subscription *sub)
>> +{
>> +	if (sub->type != V4L2_EVENT_FRAME_SYNC)
>> +		return -EINVAL;
>> +
>> +	/* Line number. For now only zero accepted. */
>> +	if (sub->id != 0)
>> +		return -EINVAL;
>> +
>> +	return v4l2_event_subscribe(fh, sub, 0, NULL);
>> +}
>> +
>> +static const struct v4l2_subdev_pad_ops rkisp1_isp_sd_pad_ops = {
>> +	.enum_mbus_code = rkisp1_isp_sd_enum_mbus_code,
>> +	.get_selection = rkisp1_isp_sd_get_selection,
>> +	.set_selection = rkisp1_isp_sd_set_selection,
>> +	.init_cfg = rkisp1_isp_sd_init_config,
>> +	.get_fmt = rkisp1_isp_sd_get_fmt,
>> +	.set_fmt = rkisp1_isp_sd_set_fmt,
>> +	.link_validate = rkisp1_subdev_fmt_link_validate,
>> +};
>> +
>> +static const struct media_entity_operations rkisp1_isp_sd_media_ops = {
>> +	.link_validate = rkisp1_subdev_link_validate,
>> +};
>> +
>> +static const struct v4l2_subdev_video_ops rkisp1_isp_sd_video_ops = {
>> +	.s_stream = rkisp1_isp_sd_s_stream,
>> +};
>> +
>> +static const struct v4l2_subdev_core_ops rkisp1_isp_core_ops = {
>> +	.subscribe_event = rkisp1_isp_sd_subs_evt,
>> +	.unsubscribe_event = v4l2_event_subdev_unsubscribe,
>> +	.s_power = rkisp1_isp_sd_s_power,
>> +};
>> +
>> +static struct v4l2_subdev_ops rkisp1_isp_sd_ops = {
> 
> const
> 
>> +	.core = &rkisp1_isp_core_ops,
>> +	.video = &rkisp1_isp_sd_video_ops,
>> +	.pad = &rkisp1_isp_sd_pad_ops,
>> +};
>> +
>> +static void rkisp1_isp_sd_init_default_fmt(struct rkisp1_isp_subdev *isp_sd)
>> +{
>> +	struct v4l2_mbus_framefmt *in_frm = &isp_sd->in_frm;
>> +	struct v4l2_rect *in_crop = &isp_sd->in_crop;
>> +	struct v4l2_rect *out_crop = &isp_sd->out_crop;
>> +	struct ispsd_in_fmt *in_fmt = &isp_sd->in_fmt;
>> +	struct ispsd_out_fmt *out_fmt = &isp_sd->out_fmt;
>> +
>> +	*in_fmt = rkisp1_isp_input_formats[0];
>> +	in_frm->width = RKISP1_DEFAULT_WIDTH;
>> +	in_frm->height = RKISP1_DEFAULT_HEIGHT;
>> +	in_frm->code = in_fmt->mbus_code;
>> +
>> +	in_crop->width = in_frm->width;
>> +	in_crop->height = in_frm->height;
>> +	in_crop->left = 0;
>> +	in_crop->top = 0;
>> +
>> +	/* propagate to source */
>> +	*out_crop = *in_crop;
>> +	*out_fmt = rkisp1_isp_output_formats[0];
>> +	isp_sd->quantization = V4L2_QUANTIZATION_FULL_RANGE;
>> +}
>> +
>> +int rkisp1_register_isp_subdev(struct rkisp1_device *isp_dev,
>> +			       struct v4l2_device *v4l2_dev)
>> +{
>> +	struct rkisp1_isp_subdev *isp_sdev = &isp_dev->isp_sdev;
>> +	struct v4l2_subdev *sd = &isp_sdev->sd;
>> +	int ret;
>> +
>> +	v4l2_subdev_init(sd, &rkisp1_isp_sd_ops);
>> +	sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS;
>> +	sd->entity.ops = &rkisp1_isp_sd_media_ops;
>> +	snprintf(sd->name, sizeof(sd->name), "rkisp1-isp-subdev");
> 
> strscpy()
> 
>> +
>> +	isp_sdev->pads[RKISP1_ISP_PAD_SINK].flags =
>> +		MEDIA_PAD_FL_SINK | MEDIA_PAD_FL_MUST_CONNECT;
>> +	isp_sdev->pads[RKISP1_ISP_PAD_SINK_PARAMS].flags = MEDIA_PAD_FL_SINK;
>> +	isp_sdev->pads[RKISP1_ISP_PAD_SOURCE_PATH].flags = MEDIA_PAD_FL_SOURCE;
>> +	isp_sdev->pads[RKISP1_ISP_PAD_SOURCE_STATS].flags = MEDIA_PAD_FL_SOURCE;
>> +	sd->entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
>> +	ret = media_entity_pads_init(&sd->entity, RKISP1_ISP_PAD_MAX,
>> +				     isp_sdev->pads);
>> +	if (ret < 0)
>> +		return ret;
>> +
>> +	sd->owner = THIS_MODULE;
>> +	v4l2_set_subdevdata(sd, isp_dev);
>> +
>> +	sd->grp_id = GRP_ID_ISP;
>> +	ret = v4l2_device_register_subdev(v4l2_dev, sd);
>> +	if (ret < 0) {
>> +		v4l2_err(sd, "Failed to register isp subdev\n");
>> +		goto err_cleanup_media_entity;
>> +	}
>> +
>> +	rkisp1_isp_sd_init_default_fmt(isp_sdev);
>> +
>> +	return 0;
> 
> A newline would be nice here.
> 
>> +err_cleanup_media_entity:
>> +	media_entity_cleanup(&sd->entity);
> 
> And here.
> 
>> +	return ret;
>> +}
>> +
>> +void rkisp1_unregister_isp_subdev(struct rkisp1_device *isp_dev)
>> +{
>> +	struct v4l2_subdev *sd = &isp_dev->isp_sdev.sd;
>> +
>> +	v4l2_device_unregister_subdev(sd);
>> +	media_entity_cleanup(&sd->entity);
>> +}
>> +
>> +/****************  Interrupter Handler ****************/
>> +
>> +void rkisp1_mipi_isr(unsigned int mis, struct rkisp1_device *dev)
>> +{
>> +	struct v4l2_device *v4l2_dev = &dev->v4l2_dev;
>> +	void __iomem *base = dev->base_addr;
>> +	u32 val;
>> +
>> +	writel(~0, base + CIF_MIPI_ICR);
>> +
>> +	/*
>> +	 * Disable DPHY errctrl interrupt, because this dphy
>> +	 * erctrl signal is asserted until the next changes
>> +	 * of line state. This time is may be too long and cpu
>> +	 * is hold in this interrupt.
>> +	 */
>> +	if (mis & CIF_MIPI_ERR_CTRL(0x0f)) {
>> +		val = readl(base + CIF_MIPI_IMSC);
>> +		writel(val & ~CIF_MIPI_ERR_CTRL(0x0f), base + CIF_MIPI_IMSC);
>> +		dev->isp_sdev.dphy_errctrl_disabled = true;
>> +	}
>> +
>> +	/*
>> +	 * Enable DPHY errctrl interrupt again, if mipi have receive
>> +	 * the whole frame without any error.
>> +	 */
>> +	if (mis == CIF_MIPI_FRAME_END) {
>> +		/*
>> +		 * Enable DPHY errctrl interrupt again, if mipi have receive
>> +		 * the whole frame without any error.
>> +		 */
>> +		if (dev->isp_sdev.dphy_errctrl_disabled) {
>> +			val = readl(base + CIF_MIPI_IMSC);
>> +			val |= CIF_MIPI_ERR_CTRL(0x0f);
>> +			writel(val, base + CIF_MIPI_IMSC);
>> +			dev->isp_sdev.dphy_errctrl_disabled = false;
>> +		}
>> +	} else {
>> +		v4l2_warn(v4l2_dev, "MIPI mis error: 0x%08x\n", mis);
>> +	}
>> +}
>> +
>> +void rkisp1_isp_isr(unsigned int isp_mis, struct rkisp1_device *dev)
>> +{
>> +	void __iomem *base = dev->base_addr;
>> +	unsigned int isp_mis_tmp = 0;
>> +	unsigned int isp_err = 0;
>> +
>> +	/* start edge of v_sync */
>> +	if (isp_mis & CIF_ISP_V_START) {
>> +		rkisp1_isp_queue_event_sof(&dev->isp_sdev);
>> +
>> +		writel(CIF_ISP_V_START, base + CIF_ISP_ICR);
>> +		isp_mis_tmp = readl(base + CIF_ISP_MIS);
>> +		if (isp_mis_tmp & CIF_ISP_V_START)
>> +			v4l2_err(&dev->v4l2_dev, "isp icr v_statr err: 0x%x\n",
>> +				 isp_mis_tmp);
>> +	}
>> +
>> +	if ((isp_mis & CIF_ISP_PIC_SIZE_ERROR)) {
> 
> Extra parentheses.
> 
>> +		/* Clear pic_size_error */
>> +		writel(CIF_ISP_PIC_SIZE_ERROR, base + CIF_ISP_ICR);
>> +		isp_err = readl(base + CIF_ISP_ERR);
>> +		v4l2_err(&dev->v4l2_dev,
>> +			 "CIF_ISP_PIC_SIZE_ERROR (0x%08x)", isp_err);
>> +		writel(isp_err, base + CIF_ISP_ERR_CLR);
>> +	} else if ((isp_mis & CIF_ISP_DATA_LOSS)) {
>> +		/* Clear data_loss */
>> +		writel(CIF_ISP_DATA_LOSS, base + CIF_ISP_ICR);
>> +		v4l2_err(&dev->v4l2_dev, "CIF_ISP_DATA_LOSS\n");
>> +		writel(CIF_ISP_DATA_LOSS, base + CIF_ISP_ICR);
>> +	}
>> +
>> +	/* sampled input frame is complete */
>> +	if (isp_mis & CIF_ISP_FRAME_IN) {
>> +		writel(CIF_ISP_FRAME_IN, base + CIF_ISP_ICR);
>> +		isp_mis_tmp = readl(base + CIF_ISP_MIS);
>> +		if (isp_mis_tmp & CIF_ISP_FRAME_IN)
>> +			v4l2_err(&dev->v4l2_dev, "isp icr frame_in err: 0x%x\n",
>> +				 isp_mis_tmp);
>> +	}
>> +
>> +	/* frame was completely put out */
>> +	if (isp_mis & CIF_ISP_FRAME) {
>> +		u32 isp_ris = 0;
>> +		/* Clear Frame In (ISP) */
>> +		writel(CIF_ISP_FRAME, base + CIF_ISP_ICR);
>> +		isp_mis_tmp = readl(base + CIF_ISP_MIS);
>> +		if (isp_mis_tmp & CIF_ISP_FRAME)
>> +			v4l2_err(&dev->v4l2_dev,
>> +				 "isp icr frame end err: 0x%x\n", isp_mis_tmp);
>> +
>> +		isp_ris = readl(base + CIF_ISP_RIS);
>> +		if (isp_ris & (CIF_ISP_AWB_DONE | CIF_ISP_AFM_FIN |
>> +			       CIF_ISP_EXP_END | CIF_ISP_HIST_MEASURE_RDY))
>> +			rkisp1_stats_isr(&dev->stats_vdev, isp_ris);
>> +	}
>> +
>> +	/*
>> +	 * Then update changed configs. Some of them involve
>> +	 * lot of register writes. Do those only one per frame.
>> +	 * Do the updates in the order of the processing flow.
>> +	 */
>> +	rkisp1_params_isr(&dev->params_vdev, isp_mis);
>> +}
>> diff --git a/drivers/media/platform/rockchip/isp1/rkisp1.h b/drivers/media/platform/rockchip/isp1/rkisp1.h
>> new file mode 100644
>> index 000000000000..b0366e354ec2
>> --- /dev/null
>> +++ b/drivers/media/platform/rockchip/isp1/rkisp1.h
>> @@ -0,0 +1,111 @@
>> +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
>> +/*
>> + * Rockchip isp1 driver
>> + *
>> + * Copyright (C) 2017 Rockchip Electronics Co., Ltd.
>> + */
>> +
>> +#ifndef _RKISP1_H
>> +#define _RKISP1_H
>> +
>> +#include <linux/platform_device.h>
>> +#include <media/v4l2-fwnode.h>
>> +
>> +#include "common.h"
>> +
>> +struct rkisp1_stream;
>> +
>> +/*
>> + * struct ispsd_in_fmt - ISP intput-pad format
>> + *
>> + * Translate mbus_code to hardware format values
>> + *
>> + * @bus_width: used for parallel
>> + */
>> +struct ispsd_in_fmt {
>> +	u32 mbus_code;
>> +	u8 fmt_type;
>> +	u32 mipi_dt;
>> +	u32 yuv_seq;
>> +	enum rkisp1_fmt_raw_pat_type bayer_pat;
>> +	u8 bus_width;
>> +};
>> +
>> +struct ispsd_out_fmt {
>> +	u32 mbus_code;
>> +	u8 fmt_type;
>> +};
>> +
>> +struct rkisp1_ie_config {
>> +	unsigned int effect;
>> +};
>> +
>> +enum rkisp1_isp_pad {
>> +	RKISP1_ISP_PAD_SINK,
>> +	RKISP1_ISP_PAD_SINK_PARAMS,
>> +	RKISP1_ISP_PAD_SOURCE_PATH,
>> +	RKISP1_ISP_PAD_SOURCE_STATS,
>> +	RKISP1_ISP_PAD_MAX
>> +};
>> +
>> +/*
>> + * struct rkisp1_isp_subdev - ISP sub-device
>> + *
>> + * See Cropping regions of ISP in rkisp1.c for details
>> + * @in_frm: input size, don't have to be equal to sensor size
>> + * @in_fmt: input format
>> + * @in_crop: crop for sink pad
>> + * @out_fmt: output format
>> + * @out_crop: output size
>> + *
>> + * @dphy_errctrl_disabled: if dphy errctrl is disabled(avoid endless interrupt)
>> + * @frm_sync_seq: frame sequence, to sync frame_id between video devices.
>> + * @quantization: output quantization
>> + */
>> +struct rkisp1_isp_subdev {
>> +	struct v4l2_subdev sd;
>> +	struct media_pad pads[RKISP1_ISP_PAD_MAX];
>> +	struct v4l2_ctrl_handler ctrl_handler;
>> +	struct v4l2_mbus_framefmt in_frm;
>> +	struct ispsd_in_fmt in_fmt;
>> +	struct v4l2_rect in_crop;
>> +	struct ispsd_out_fmt out_fmt;
>> +	struct v4l2_rect out_crop;
>> +	bool dphy_errctrl_disabled;
>> +	atomic_t frm_sync_seq;
>> +	enum v4l2_quantization quantization;
>> +};
>> +
>> +int rkisp1_register_isp_subdev(struct rkisp1_device *isp_dev,
>> +			       struct v4l2_device *v4l2_dev);
>> +
>> +void rkisp1_unregister_isp_subdev(struct rkisp1_device *isp_dev);
>> +
>> +void rkisp1_mipi_isr(unsigned int mipi_mis, struct rkisp1_device *dev);
>> +
>> +void rkisp1_isp_isr(unsigned int isp_mis, struct rkisp1_device *dev);
>> +
>> +static inline
>> +struct ispsd_out_fmt *rkisp1_get_ispsd_out_fmt(struct rkisp1_isp_subdev *isp_sdev)
>> +{
>> +	return &isp_sdev->out_fmt;
>> +}
>> +
>> +static inline
>> +struct ispsd_in_fmt *rkisp1_get_ispsd_in_fmt(struct rkisp1_isp_subdev *isp_sdev)
>> +{
>> +	return &isp_sdev->in_fmt;
>> +}
>> +
>> +static inline
>> +struct v4l2_rect *rkisp1_get_isp_sd_win(struct rkisp1_isp_subdev *isp_sdev)
>> +{
>> +	return &isp_sdev->out_crop;
>> +}
> 
> I'd just use the struct fields directly in the code as it's easier to
> figure out which field in the struct is being accessed.
> 
>> +
>> +static inline struct rkisp1_isp_subdev *sd_to_isp_sd(struct v4l2_subdev *sd)
>> +{
>> +	return container_of(sd, struct rkisp1_isp_subdev, sd);
>> +}
>> +
>> +#endif /* _RKISP1_H */
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel