From: Luca Weiss <luca@z3ntu.xyz>
To: linux-arm-msm@vger.kernel.org
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>,
Ohad Ben-Cohen <ohad@wizery.com>,
Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>,
linux-remoteproc@vger.kernel.org, linux-kernel@vger.kernel.org,
Sibi Sankar <sibis@codeaurora.org>,
Jeffrey Hugo <jeffrey.l.hugo@gmail.com>,
Brian Masney <masneyb@onstation.org>
Subject: Re: [PATCH v2 2/2] remoteproc: qcom_q6v5_mss: Validate each segment during loading
Date: Sun, 10 Nov 2019 15:05:54 +0100 [thread overview]
Message-ID: <393350950.66DGQb6nHQ@g550jk> (raw)
In-Reply-To: <20191109004033.1496871-3-bjorn.andersson@linaro.org>
[-- Attachment #1: Type: text/plain, Size: 7811 bytes --]
Hi Bjorn,
with your patches and modifications in qcom-msm8974.dtsi, I can boot the modem
successfully on the Fairphone 2, without the 'hack' commit we had in the tree
before! Thanks!
Tested-by: Luca Weiss <luca@z3ntu.xyz>
On Samstag, 9. November 2019 01:40:33 CET Bjorn Andersson wrote:
> The code used to sync with the MBA after each segment loaded and this is
> still what's done downstream. So reduce the delta towards downstream by
> switching to a model where the content is iteratively validated.
>
> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
> Tested-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>
> Changes since v1:
> - Picked up Jeff's r-b and t-b
>
> drivers/remoteproc/qcom_q6v5_mss.c | 76 ++++++++++++++++++++----------
> 1 file changed, 51 insertions(+), 25 deletions(-)
>
> diff --git a/drivers/remoteproc/qcom_q6v5_mss.c
> b/drivers/remoteproc/qcom_q6v5_mss.c index efab574b2e12..914d5546e1cf
> 100644
> --- a/drivers/remoteproc/qcom_q6v5_mss.c
> +++ b/drivers/remoteproc/qcom_q6v5_mss.c
> @@ -358,23 +358,29 @@ static void q6v5_pds_disable(struct q6v5 *qproc,
> struct device **pds, }
>
> static int q6v5_xfer_mem_ownership(struct q6v5 *qproc, int *current_perm,
> - bool remote_owner, phys_addr_t
addr,
> + bool local, bool remote,
phys_addr_t addr,
> size_t size)
> {
> - struct qcom_scm_vmperm next;
> + struct qcom_scm_vmperm next[2];
> + int perms = 0;
>
> if (!qproc->need_mem_protection)
> return 0;
> - if (remote_owner && *current_perm == BIT(QCOM_SCM_VMID_MSS_MSA))
> - return 0;
> - if (!remote_owner && *current_perm == BIT(QCOM_SCM_VMID_HLOS))
> - return 0;
>
> - next.vmid = remote_owner ? QCOM_SCM_VMID_MSS_MSA :
QCOM_SCM_VMID_HLOS;
> - next.perm = remote_owner ? QCOM_SCM_PERM_RW : QCOM_SCM_PERM_RWX;
> + if (local) {
> + next[perms].vmid = QCOM_SCM_VMID_HLOS;
> + next[perms].perm = QCOM_SCM_PERM_RWX;
> + perms++;
> + }
> +
> + if (remote) {
> + next[perms].vmid = QCOM_SCM_VMID_MSS_MSA;
> + next[perms].perm = QCOM_SCM_PERM_RW;
> + perms++;
> + }
>
> return qcom_scm_assign_mem(addr, ALIGN(size, SZ_4K),
> - current_perm, &next, 1);
> + current_perm, next, perms);
> }
>
> static int q6v5_load(struct rproc *rproc, const struct firmware *fw)
> @@ -681,7 +687,7 @@ static int q6v5_mpss_init_image(struct q6v5 *qproc,
> const struct firmware *fw)
>
> /* Hypervisor mapping to access metadata by modem */
> mdata_perm = BIT(QCOM_SCM_VMID_HLOS);
> - ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, true, phys,
size);
> + ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, false, true,
phys,
> size); if (ret) {
> dev_err(qproc->dev,
> "assigning Q6 access to metadata failed:
%d\n", ret);
> @@ -699,7 +705,7 @@ static int q6v5_mpss_init_image(struct q6v5 *qproc,
> const struct firmware *fw) dev_err(qproc->dev, "MPSS header authentication
> failed: %d\n", ret);
>
> /* Metadata authentication done, remove modem access */
> - xferop_ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, false,
phys,
> size); + xferop_ret = q6v5_xfer_mem_ownership(qproc, &mdata_perm, true,
> false, phys, size); if (xferop_ret)
> dev_warn(qproc->dev,
> "mdt buffer not reclaimed system may become
unstable\n");
> @@ -786,7 +792,7 @@ static int q6v5_mba_load(struct q6v5 *qproc)
> }
>
> /* Assign MBA image access in DDR to q6 */
> - ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true,
> + ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false, true,
> qproc->mba_phys, qproc-
>mba_size);
> if (ret) {
> dev_err(qproc->dev,
> @@ -820,8 +826,8 @@ static int q6v5_mba_load(struct q6v5 *qproc)
> q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc);
>
> reclaim_mba:
> - xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm,
false,
> - qproc-
>mba_phys,
> + xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm,
true,
> + false,
qproc->mba_phys,
> qproc-
>mba_size);
> if (xfermemop_ret) {
> dev_err(qproc->dev,
> @@ -888,7 +894,7 @@ static void q6v5_mba_reclaim(struct q6v5 *qproc)
> /* In case of failure or coredump scenario where reclaiming MBA
memory
> * could not happen reclaim it here.
> */
> - ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, false,
> + ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm, true, false,
> qproc->mba_phys,
> qproc->mba_size);
> WARN_ON(ret);
> @@ -915,6 +921,7 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
> phys_addr_t boot_addr;
> phys_addr_t min_addr = PHYS_ADDR_MAX;
> phys_addr_t max_addr = 0;
> + u32 code_length;
> bool relocate = false;
> char *fw_name;
> size_t fw_name_len;
> @@ -965,9 +972,19 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
> }
>
> /* Try to reset ownership back to Linux */
> - q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false,
> + q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true, false,
> qproc->mpss_phys, qproc-
>mpss_size);
>
> + /* Share ownership between Linux and MSS, during segment loading */
> + ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true, true,
> + qproc->mpss_phys, qproc-
>mpss_size);
> + if (ret) {
> + dev_err(qproc->dev,
> + "assigning Q6 access to mpss memory failed:
%d\n", ret);
> + ret = -EAGAIN;
> + goto release_firmware;
> + }
> +
> mpss_reloc = relocate ? min_addr : qproc->mpss_phys;
> qproc->mpss_reloc = mpss_reloc;
> /* Load firmware segments */
> @@ -1016,10 +1033,24 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
> phdr->p_memsz - phdr->p_filesz);
> }
> size += phdr->p_memsz;
> +
> + code_length = readl(qproc->rmb_base +
RMB_PMI_CODE_LENGTH_REG);
> + if (!code_length) {
> + boot_addr = relocate ? qproc->mpss_phys :
min_addr;
> + writel(boot_addr, qproc->rmb_base +
RMB_PMI_CODE_START_REG);
> + writel(RMB_CMD_LOAD_READY, qproc->rmb_base +
RMB_MBA_COMMAND_REG);
> + }
> + writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
> +
> + ret = readl(qproc->rmb_base + RMB_MBA_STATUS_REG);
> + if (ret < 0) {
> + dev_err(qproc->dev, "MPSS authentication
failed: %d\n", ret);
> + goto release_firmware;
> + }
> }
>
> /* Transfer ownership of modem ddr region to q6 */
> - ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true,
> + ret = q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, false,
true,
> qproc->mpss_phys, qproc-
>mpss_size);
> if (ret) {
> dev_err(qproc->dev,
> @@ -1028,11 +1059,6 @@ static int q6v5_mpss_load(struct q6v5 *qproc)
> goto release_firmware;
> }
>
> - boot_addr = relocate ? qproc->mpss_phys : min_addr;
> - writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG);
> - writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG);
> - writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG);
> -
> ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_AUTH_COMPLETE, 10000);
> if (ret == -ETIMEDOUT)
> dev_err(qproc->dev, "MPSS authentication timed out\n");
> @@ -1061,7 +1087,7 @@ static void qcom_q6v5_dump_segment(struct rproc
> *rproc, ret = q6v5_mba_load(qproc);
>
> /* Try to reset ownership back to Linux */
> - q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm,
false,
> + q6v5_xfer_mem_ownership(qproc, &qproc->mpss_perm, true,
false,
> qproc->mpss_phys,
qproc->mpss_size);
> }
>
> @@ -1101,8 +1127,8 @@ static int q6v5_start(struct rproc *rproc)
> goto reclaim_mpss;
> }
>
> - xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm,
false,
> - qproc-
>mba_phys,
> + xfermemop_ret = q6v5_xfer_mem_ownership(qproc, &qproc->mba_perm,
true,
> + false,
qproc->mba_phys,
> qproc-
>mba_size);
> if (xfermemop_ret)
> dev_err(qproc->dev,
[-- Attachment #2: This is a digitally signed message part. --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2019-11-10 14:06 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-09 0:40 [PATCH v2 0/2] remoteproc: mss: Improve mem_assign and firmware load Bjorn Andersson
2019-11-09 0:40 ` [PATCH v2 1/2] remoteproc: qcom_q6v5_mss: Don't reassign mpss region on shutdown Bjorn Andersson
2019-11-12 17:01 ` Jeffrey Hugo
2019-11-13 18:02 ` Jeffrey Hugo
2019-11-09 0:40 ` [PATCH v2 2/2] remoteproc: qcom_q6v5_mss: Validate each segment during loading Bjorn Andersson
2019-11-10 14:05 ` Luca Weiss [this message]
2019-11-11 6:45 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=393350950.66DGQb6nHQ@g550jk \
--to=luca@z3ntu.xyz \
--cc=akdwived@codeaurora.org \
--cc=bjorn.andersson@linaro.org \
--cc=jeffrey.l.hugo@gmail.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=masneyb@onstation.org \
--cc=ohad@wizery.com \
--cc=sibis@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).