From: Baruch Siach <baruch@tkos.co.il>
To: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>,
Kathiravan T <kathirav@codeaurora.org>,
Bjorn Helgaas <bhelgaas@google.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Thierry Reding <thierry.reding@gmail.com>,
Jonathan Hunter <jonathanh@nvidia.com>,
Jingoo Han <jingoohan1@gmail.com>,
Gustavo Pimentel <gustavo.pimentel@synopsys.com>,
Robert Marko <robert.marko@sartura.hr>,
devicetree@vger.kernel.org, linux-phy@lists.infradead.org,
PCI <linux-pci@vger.kernel.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
linux-arm-kernel <linux-arm-kernel@lists.infradead.org>,
linux-tegra <linux-tegra@vger.kernel.org>
Subject: Re: [PATCH v2 2/6] PCI: qcom: add support for IPQ60xx PCIe controller
Date: Wed, 25 Aug 2021 14:15:38 +0300 [thread overview]
Message-ID: <87o89lahqp.fsf@tarshish> (raw)
In-Reply-To: <CAL_JsqKOGo4eXKA7FZK7AQQ24MDDbg2-ngUQF9CJK=8eH_pxHQ@mail.gmail.com>
Hi Rob,
On Fri, Aug 06 2021, Rob Herring wrote:
> On Wed, May 5, 2021 at 3:18 AM Baruch Siach <baruch@tkos.co.il> wrote:
>>
>> From: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>>
>> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
>> platform.
>>
>> The code is based on downstream Codeaurora kernel v5.4. Split out the
>> DBI registers access part from .init into .post_init. DBI registers are
>> only accessible after phy_power_on().
>>
>> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
>> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
>> ---
>> v2:
>> * Drop ATU configuration; rely on common code instead
>>
>> * Use more common register macros
>>
>> * Use bulk clk and reset APIs
>> ---
>> drivers/pci/controller/dwc/pcie-designware.h | 1 +
>> drivers/pci/controller/dwc/pcie-qcom.c | 150 +++++++++++++++++++
>> 2 files changed, 151 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
>> index ceb359b6e6a6..346462c74a3e 100644
>> --- a/drivers/pci/controller/dwc/pcie-designware.h
>> +++ b/drivers/pci/controller/dwc/pcie-designware.h
>> @@ -76,6 +76,7 @@
>>
>> #define GEN3_RELATED_OFF 0x890
>> #define GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL BIT(0)
>> +#define GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS BIT(13)
>> #define GEN3_RELATED_OFF_GEN3_EQ_DISABLE BIT(16)
>> #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_SHIFT 24
>> #define GEN3_RELATED_OFF_RATE_SHADOW_SEL_MASK GENMASK(25, 24)
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
>> index 8a7a300163e5..93766aee3e7c 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>> @@ -52,6 +52,10 @@
>> #define PCIE20_PARF_DBI_BASE_ADDR 0x168
>> #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16C
>> #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174
>> +#define AHB_CLK_EN BIT(0)
>> +#define MSTR_AXI_CLK_EN BIT(1)
>> +#define BYPASS BIT(4)
>> +
>> #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x178
>> #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 0x1A8
>> #define PCIE20_PARF_LTSSM 0x1B0
>> @@ -94,6 +98,12 @@
>> #define SLV_ADDR_SPACE_SZ 0x10000000
>>
>> #define PCIE20_LNK_CONTROL2_LINK_STATUS2 0xa0
>> +#define PCIE_CAP_CURR_DEEMPHASIS BIT(16)
>
> Isn't this a standard register field?
I don't know. I could not find any reference to this field or the
registers it's part of.
n
>> +#define SPEED_GEN1 0x1
>> +#define SPEED_GEN2 0x2
>> +#define SPEED_GEN3 0x3
>
> And these?
>
> There's already some common DWC code for setting the link speed.
dw_pcie_link_set_max_speed() deals with other registers, as far as I can
see.
>> +#define AXI_CLK_RATE 200000000
>> +#define RCHNG_CLK_RATE 100000000
>>
>> #define DEVICE_TYPE_RC 0x4
[snip]
>> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
>> +{
>> + struct dw_pcie *pci = pcie->pci;
>> + u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
>> + u32 val;
>> + int i;
>> +
>> + writel(SLV_ADDR_SPACE_SZ,
>> + pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
>> +
>> + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
>> + val &= ~BIT(0);
>> + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
>> +
>> + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
>> +
>> + writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
>> + writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
>> + pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
>> + writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
>> + | GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,
>> + pci->dbi_base + GEN3_RELATED_OFF);
>> +
>> + writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
>> + | SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |
>> + AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
>> + pcie->parf + PCIE20_PARF_SYS_CTRL);
>> +
>> + writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
>> +
>> + dw_pcie_dbi_ro_wr_en(pci);
>> + writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>> +
>> + /* Configure PCIe link capabilities for ASPM */
>> + val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> + val &= ~PCI_EXP_LNKCAP_ASPMS;
>> + writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
>> +
>> + writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
>> + PCI_EXP_DEVCTL2);
>> +
>> + writel(PCIE_CAP_CURR_DEEMPHASIS | SPEED_GEN3,
>> + pci->dbi_base + offset + PCI_EXP_DEVCTL2);
>
> Doesn't this overwrite the prior register write?
It does. There are two mistakes here. The writel() above should set
PCIE20_DEVICE_CONTROL2_STATUS2 (offset 0x98). This writel() should set
PCIE20_LNK_CONTROL2_LINK_STATUS2 (offset 0xa0). So both are wrong.
>> +
>> + for (i = 0;i < 256;i++)
>> + writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
>> + + (4 * i));
>> +
>> + return 0;
>> +}
Thanks,
baruch
--
~. .~ Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
- baruch@tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -
next prev parent reply other threads:[~2021-08-25 11:25 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-05 9:18 [PATCH v2 0/6] arm64: IPQ6018 PCIe support Baruch Siach
2021-05-05 9:18 ` [PATCH v2 1/6] PCI: dwc: tegra: move GEN3_RELATED DBI register to common header Baruch Siach
2021-08-06 19:47 ` Rob Herring
2021-05-05 9:18 ` [PATCH v2 2/6] PCI: qcom: add support for IPQ60xx PCIe controller Baruch Siach
2021-08-06 19:59 ` Rob Herring
2021-08-25 11:15 ` Baruch Siach [this message]
2021-08-25 13:38 ` Rob Herring
2021-08-25 14:09 ` Baruch Siach
2021-08-25 15:03 ` Rob Herring
2021-08-25 16:05 ` Bjorn Helgaas
2021-08-25 16:37 ` Bjorn Helgaas
2021-05-05 9:18 ` [PATCH v2 3/6] phy: qcom-qmp: add QMP V2 PCIe PHY support for ipq60xx Baruch Siach
2021-05-14 11:43 ` Vinod Koul
2021-05-05 9:18 ` [PATCH v2 4/6] arm64: dts: ipq6018: Add pcie support Baruch Siach
2021-05-05 9:18 ` [PATCH v2 5/6] dt-bindings: phy: qcom,qmp: Add IPQ60xx PCIe PHY bindings Baruch Siach
2021-05-14 11:43 ` Vinod Koul
2021-05-05 9:18 ` [PATCH v2 6/6] dt-bindings: pci: qcom: Document PCIe bindings for IPQ6018 SoC Baruch Siach
2021-05-14 11:43 ` Vinod Koul
2021-08-05 6:58 ` [PATCH v2 0/6] arm64: IPQ6018 PCIe support Baruch Siach
2021-08-05 9:42 ` Lorenzo Pieralisi
2021-08-06 12:48 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87o89lahqp.fsf@tarshish \
--to=baruch@tkos.co.il \
--cc=agross@kernel.org \
--cc=bhelgaas@google.com \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=gustavo.pimentel@synopsys.com \
--cc=jingoohan1@gmail.com \
--cc=jonathanh@nvidia.com \
--cc=kathirav@codeaurora.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=linux-tegra@vger.kernel.org \
--cc=robert.marko@sartura.hr \
--cc=robh+dt@kernel.org \
--cc=speriaka@codeaurora.org \
--cc=thierry.reding@gmail.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).