From: Rob Clark <robdclark@gmail.com>
To: Sharat Masetty <smasetty@codeaurora.org>
Cc: freedreno <freedreno@lists.freedesktop.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Douglas Anderson <dianders@chromium.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Jordan Crouse <jcrouse@codeaurora.org>,
Matthias Kaehlcke <mka@chromium.org>,
dri-devel@freedesktop.org
Subject: Re: [Freedreno] [PATCH v6] arm64: dts: qcom: sc7180: Add A618 gpu dt blob
Date: Thu, 20 Feb 2020 08:19:20 -0800 [thread overview]
Message-ID: <CAF6AEGuFfaYuYoXkGJHit4X0Hp2-i0yMkWCfoKtLwPyGkjpkVA@mail.gmail.com> (raw)
In-Reply-To: <1581320465-15854-2-git-send-email-smasetty@codeaurora.org>
On Sun, Feb 9, 2020 at 11:41 PM Sharat Masetty <smasetty@codeaurora.org> wrote:
>
> This patch adds the required dt nodes and properties
> to enabled A618 GPU.
>
> Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
> ---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 102 +++++++++++++++++++++++++++++++++++
> 1 file changed, 102 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index f3fcc5c..63fff15 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -1043,6 +1043,108 @@
> };
> };
>
> + gpu: gpu@5000000 {
> + compatible = "qcom,adreno-618.0", "qcom,adreno";
> + #stream-id-cells = <16>;
> + reg = <0 0x05000000 0 0x40000>, <0 0x0509e000 0 0x1000>,
> + <0 0x05061000 0 0x800>;
> + reg-names = "kgsl_3d0_reg_memory", "cx_mem", "cx_dbgc";
> + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
> + iommus = <&adreno_smmu 0>;
> + operating-points-v2 = <&gpu_opp_table>;
> + qcom,gmu = <&gmu>;
> +
> + gpu_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-800000000 {
> + opp-hz = /bits/ 64 <800000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
> + };
> +
> + opp-650000000 {
> + opp-hz = /bits/ 64 <650000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
> + };
> +
> + opp-565000000 {
> + opp-hz = /bits/ 64 <565000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
> + };
> +
> + opp-430000000 {
> + opp-hz = /bits/ 64 <430000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
> + };
> +
> + opp-355000000 {
> + opp-hz = /bits/ 64 <355000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
> + };
> +
> + opp-267000000 {
> + opp-hz = /bits/ 64 <267000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
> + };
> +
> + opp-180000000 {
> + opp-hz = /bits/ 64 <180000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
> + };
> + };
> + };
> +
> + adreno_smmu: iommu@5040000 {
> + compatible = "qcom,sc7180-smmu-v2", "qcom,smmu-v2";
> + reg = <0 0x05040000 0 0x10000>;
> + #iommu-cells = <1>;
> + #global-interrupts = <2>;
> + interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 366 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 367 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 368 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 369 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 370 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 371 IRQ_TYPE_EDGE_RISING>;
> + clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
> + <&gcc GCC_GPU_CFG_AHB_CLK>,
> + <&gcc GCC_DDRSS_GPU_AXI_CLK>;
> +
> + clock-names = "bus", "iface", "mem_iface_clk";
> + power-domains = <&gpucc CX_GDSC>;
> + };
> +
> + gmu: gmu@506a000 {
> + compatible="qcom,adreno-gmu-618.0", "qcom,adreno-gmu";
> + reg = <0 0x0506a000 0 0x31000>, <0 0x0b290000 0 0x10000>,
> + <0 0x0b490000 0 0x10000>;
> + reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
> + interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "hfi", "gmu";
> + clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
> + <&gpucc GPU_CC_CXO_CLK>,
> + <&gcc GCC_DDRSS_GPU_AXI_CLK>,
> + <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
> + clock-names = "gmu", "cxo", "axi", "memnoc";
> + power-domains = <&gpucc CX_GDSC>, <&gpucc GX_GDSC>;
> + power-domain-names = "cx", "gx";
> + iommus = <&adreno_smmu 5>;
> + operating-points-v2 = <&gmu_opp_table>;
jfyi, this will shortly require a dma-ranges property[1].. it might
simplify things, wrt. to which order patches land (this vs dma-ranges)
to go ahead and add the dma-ranges property now
BR,
-R
[1] https://lists.freedesktop.org/archives/freedreno/2020-February/006903.html
> +
> + gmu_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-200000000 {
> + opp-hz = /bits/ 64 <200000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
> + };
> + };
> + };
> +
> gpucc: clock-controller@5090000 {
> compatible = "qcom,sc7180-gpucc";
> reg = <0 0x05090000 0 0x9000>;
> --
> 1.9.1
> _______________________________________________
> Freedreno mailing list
> Freedreno@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/freedreno
prev parent reply other threads:[~2020-02-20 16:19 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-10 7:41 [PATCH v6] sc7180: Add A618 GPU bindings Sharat Masetty
2020-02-10 7:41 ` [PATCH v6] arm64: dts: qcom: sc7180: Add A618 gpu dt blob Sharat Masetty
2020-02-10 21:21 ` Doug Anderson
2020-02-20 8:20 ` Sharat Masetty
2020-02-20 16:19 ` Rob Clark [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAF6AEGuFfaYuYoXkGJHit4X0Hp2-i0yMkWCfoKtLwPyGkjpkVA@mail.gmail.com \
--to=robdclark@gmail.com \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=dri-devel@freedesktop.org \
--cc=freedreno@lists.freedesktop.org \
--cc=jcrouse@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=smasetty@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).