linux-clk.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dmitry Osipenko <digetx@gmail.com>
To: Sowjanya Komatineni <skomatineni@nvidia.com>,
	thierry.reding@gmail.com, jonathanh@nvidia.com,
	mperttunen@nvidia.com, gregkh@linuxfoundation.org,
	sboyd@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com
Cc: pdeschrijver@nvidia.com, pgaikwad@nvidia.com, spujar@nvidia.com,
	josephl@nvidia.com, daniel.lezcano@linaro.org,
	mmaddireddy@nvidia.com, markz@nvidia.com,
	devicetree@vger.kernel.org, linux-clk@vger.kernel.org,
	linux-tegra@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 06/19] soc: tegra: Add Tegra PMC clock registrations into PMC driver
Date: Fri, 20 Dec 2019 07:34:13 +0300	[thread overview]
Message-ID: <42f39288-da11-e28d-2a0e-28f1b020e674@gmail.com> (raw)
In-Reply-To: <8fa81a47-63e5-d64d-7cc6-7fdd20ff89f0@nvidia.com>

20.12.2019 07:13, Sowjanya Komatineni пишет:
> 
> On 12/19/19 5:39 PM, Dmitry Osipenko wrote:
>> 20.12.2019 04:21, Sowjanya Komatineni пишет:
>>> On 12/18/19 4:41 PM, Sowjanya Komatineni wrote:
>>>> On 12/18/19 1:44 PM, Dmitry Osipenko wrote:
>>>>> 18.12.2019 11:35, Dmitry Osipenko пишет:
>>>>>> 18.12.2019 11:30, Dmitry Osipenko пишет:
>>>>>>> 17.12.2019 23:03, Sowjanya Komatineni пишет:
>>>>>>>> Tegra PMC has clk_out_1, clk_out_2, and clk_out_3 clocks and
>>>>>>>> currently
>>>>>>>> these PMC clocks are registered by Tegra clock driver with each
>>>>>>>> clock as
>>>>>>>> separate mux and gate clocks using clk_register_mux and
>>>>>>>> clk_register_gate
>>>>>>>> by passing PMC base address and register offsets and PMC
>>>>>>>> programming for
>>>>>>>> these clocks happens through direct PMC access by the clock driver.
>>>>>>>>
>>>>>>>> With this, when PMC is in secure mode any direct PMC access from
>>>>>>>> the
>>>>>>>> non-secure world does not go through and these clocks will not be
>>>>>>>> functional.
>>>>>>>>
>>>>>>>> This patch adds these PMC clocks registration to pmc driver with
>>>>>>>> PMC as
>>>>>>>> a clock provider and registers each clock as single clock.
>>>>>>>>
>>>>>>>> clk_ops callback implementations for these clocks uses
>>>>>>>> tegra_pmc_readl and
>>>>>>>> tegra_pmc_writel which supports PMC programming in both secure
>>>>>>>> mode and
>>>>>>>> non-secure mode.
>>>>>>>>
>>>>>>>> Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
>>>>>>>> ---
>>>>>>>>    drivers/soc/tegra/pmc.c | 248
>>>>>>>> ++++++++++++++++++++++++++++++++++++++++++++++++
>>>>>>>>    1 file changed, 248 insertions(+)
>>>>>>>>
>>>>>>>> diff --git a/drivers/soc/tegra/pmc.c b/drivers/soc/tegra/pmc.c
>>>>>>>> index ea0e11a09c12..6d65194a6e71 100644
>>>>>>>> --- a/drivers/soc/tegra/pmc.c
>>>>>>>> +++ b/drivers/soc/tegra/pmc.c
>>>>>>>> @@ -13,6 +13,9 @@
>>>>>>>>      #include <linux/arm-smccc.h>
>>>>>>>>    #include <linux/clk.h>
>>>>>>>> +#include <linux/clk-provider.h>
>>>>>>>> +#include <linux/clkdev.h>
>>>>>>>> +#include <linux/clk/clk-conf.h>
>>>>>>>>    #include <linux/clk/tegra.h>
>>>>>>>>    #include <linux/debugfs.h>
>>>>>>>>    #include <linux/delay.h>
>>>>>>>> @@ -48,6 +51,7 @@
>>>>>>>>    #include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
>>>>>>>>    #include <dt-bindings/gpio/tegra186-gpio.h>
>>>>>>>>    #include <dt-bindings/gpio/tegra194-gpio.h>
>>>>>>>> +#include <dt-bindings/soc/tegra-pmc.h>
>>>>>>>>      #define PMC_CNTRL            0x0
>>>>>>>>    #define  PMC_CNTRL_INTR_POLARITY    BIT(17) /* inverts INTR
>>>>>>>> polarity */
>>>>>>>> @@ -100,6 +104,7 @@
>>>>>>>>    #define PMC_WAKE2_STATUS        0x168
>>>>>>>>    #define PMC_SW_WAKE2_STATUS        0x16c
>>>>>>>>    +#define PMC_CLK_OUT_CNTRL        0x1a8
>>>>>>>>    #define PMC_SENSOR_CTRL            0x1b0
>>>>>>>>    #define  PMC_SENSOR_CTRL_SCRATCH_WRITE    BIT(2)
>>>>>>>>    #define  PMC_SENSOR_CTRL_ENABLE_RST    BIT(1)
>>>>>>>> @@ -155,6 +160,64 @@
>>>>>>>>    #define  TEGRA_SMC_PMC_READ    0xaa
>>>>>>>>    #define  TEGRA_SMC_PMC_WRITE    0xbb
>>>>>>>>    +struct pmc_clk {
>>>>>>>> +    struct clk_hw    hw;
>>>>>>>> +    unsigned long    offs;
>>>>>>>> +    u32        mux_mask;
>>>>>>>> +    u32        mux_shift;
>>>>>>>> +    u32        gate_shift;
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +#define to_pmc_clk(_hw) container_of(_hw, struct pmc_clk, hw)
>>>>>>>> +
>>>>>>>> +struct pmc_clk_init_data {
>>>>>>>> +    char *name;
>>>>>>>> +    const char *const *parents;
>>>>>>>> +    int num_parents;
>>>>>>>> +    int clk_id;
>>>>>>>> +    u8 mux_shift;
>>>>>>>> +    u8 gate_shift;
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +static const char * const clk_out1_parents[] = { "osc",
>>>>>>>> "osc_div2",
>>>>>>>> +    "osc_div4", "extern1",
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +static const char * const clk_out2_parents[] = { "osc",
>>>>>>>> "osc_div2",
>>>>>>>> +    "osc_div4", "extern2",
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +static const char * const clk_out3_parents[] = { "osc",
>>>>>>>> "osc_div2",
>>>>>>>> +    "osc_div4", "extern3",
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +static const struct pmc_clk_init_data tegra_pmc_clks_data[] = {
>>>>>>>> +    {
>>>>>>>> +        .name = "clk_out_1",
>>>>>>>> +        .parents = clk_out1_parents,
>>>>>>>> +        .num_parents = ARRAY_SIZE(clk_out1_parents),
>>>>>>>> +        .clk_id = TEGRA_PMC_CLK_OUT_1,
>>>>>>>> +        .mux_shift = 6,
>>>>>>>> +        .gate_shift = 2,
>>>>>>> I'd replace these with a single .shift, given that mux_shift =
>>>>>>> gate_shift + 4 for all clocks.
>>>>>>>
>>>>>>>> +    },
>>>>>>>> +    {
>>>>>>>> +        .name = "clk_out_2",
>>>>>>>> +        .parents = clk_out2_parents,
>>>>>>>> +        .num_parents = ARRAY_SIZE(clk_out2_parents),
>>>>>>>> +        .clk_id = TEGRA_PMC_CLK_OUT_2,
>>>>>>>> +        .mux_shift = 14,
>>>>>>>> +        .gate_shift = 10,
>>>>>>>> +    },
>>>>>>>> +    {
>>>>>>>> +        .name = "clk_out_3",
>>>>>>>> +        .parents = clk_out3_parents,
>>>>>>>> +        .num_parents = ARRAY_SIZE(clk_out3_parents),
>>>>>>>> +        .clk_id = TEGRA_PMC_CLK_OUT_3,
>>>>>>>> +        .mux_shift = 22,
>>>>>>>> +        .gate_shift = 18,
>>>>>>>> +    },
>>>>>>>> +};
>>>>>>>> +
>>>>>>>>    struct tegra_powergate {
>>>>>>>>        struct generic_pm_domain genpd;
>>>>>>>>        struct tegra_pmc *pmc;
>>>>>>>> @@ -254,6 +317,9 @@ struct tegra_pmc_soc {
>>>>>>>>         */
>>>>>>>>        const struct tegra_wake_event *wake_events;
>>>>>>>>        unsigned int num_wake_events;
>>>>>>>> +
>>>>>>>> +    const struct pmc_clk_init_data *pmc_clks_data;
>>>>>>>> +    unsigned int num_pmc_clks;
>>>>>>>>    };
>>>>>>>>      static const char * const tegra186_reset_sources[] = {
>>>>>>>> @@ -2163,6 +2229,173 @@ static int tegra_pmc_clk_notify_cb(struct
>>>>>>>> notifier_block *nb,
>>>>>>>>        return NOTIFY_OK;
>>>>>>>>    }
>>>>>>>>    +static void pmc_clk_fence_udelay(u32 offset)
>>>>>>>> +{
>>>>>>>> +    tegra_pmc_readl(pmc, offset);
>>>>>>>> +    /* pmc clk propagation delay 2 us */
>>>>>>>> +    udelay(2);
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static u8 pmc_clk_mux_get_parent(struct clk_hw *hw)
>>>>>>>> +{
>>>>>>>> +    struct pmc_clk *clk = to_pmc_clk(hw);
>>>>>>>> +    u32 val;
>>>>>>>> +
>>>>>>>> +    val = tegra_pmc_readl(pmc, clk->offs) >> clk->mux_shift;
>>>>>>>> +    val &= clk->mux_mask;
>>>>>>>> +
>>>>>>>> +    return val;
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static int pmc_clk_mux_set_parent(struct clk_hw *hw, u8 index)
>>>>>>>> +{
>>>>>>>> +    struct pmc_clk *clk = to_pmc_clk(hw);
>>>>>>>> +    u32 val;
>>>>>>>> +
>>>>>>>> +    val = tegra_pmc_readl(pmc, clk->offs);
>>>>>>>> +    val &= ~(clk->mux_mask << clk->mux_shift);
>>>>>>>> +    val |= index << clk->mux_shift;
>>>>>>>> +    tegra_pmc_writel(pmc, val, clk->offs);
>>>>>>>> +    pmc_clk_fence_udelay(clk->offs);
>> Is this fencing applies only to clock changes or maybe it won't hurt to
>> move it into tegra_pmc_writel()?
>>
>>>>>>>> +    return 0;
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static int pmc_clk_is_enabled(struct clk_hw *hw)
>>>>>>>> +{
>>>>>>>> +    struct pmc_clk *clk = to_pmc_clk(hw);
>>>>>>>> +
>>>>>>>> +    return tegra_pmc_readl(pmc, clk->offs) & BIT(clk->gate_shift)
>>>>>>>> ? 1 : 0;
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static void pmc_clk_set_state(unsigned long offs, u32 shift, int
>>>>>>>> state)
>>>>>>>> +{
>>>>>>>> +    u32 val;
>>>>>>>> +
>>>>>>>> +    val = tegra_pmc_readl(pmc, offs);
>>>>>>>> +    val = state ? (val | BIT(shift)) : (val & ~BIT(shift));
>>>>>>>> +    tegra_pmc_writel(pmc, val, offs);
>>>>>>>> +    pmc_clk_fence_udelay(offs);
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static int pmc_clk_enable(struct clk_hw *hw)
>>>>>>>> +{
>>>>>>>> +    struct pmc_clk *clk = to_pmc_clk(hw);
>>>>>>>> +
>>>>>>>> +    pmc_clk_set_state(clk->offs, clk->gate_shift, 1);
>>>>>>>> +
>>>>>>>> +    return 0;
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static void pmc_clk_disable(struct clk_hw *hw)
>>>>>>>> +{
>>>>>>>> +    struct pmc_clk *clk = to_pmc_clk(hw);
>>>>>>>> +
>>>>>>>> +    pmc_clk_set_state(clk->offs, clk->gate_shift, 0);
>>>>>>>> +}
>>>>>>>> +
>>>>>>>> +static const struct clk_ops pmc_clk_ops = {
>>>>>>>> +    .get_parent = pmc_clk_mux_get_parent,
>>>>>>>> +    .set_parent = pmc_clk_mux_set_parent,
>>>>>>>> +    .determine_rate = __clk_mux_determine_rate,
>>>>>>>> +    .is_enabled = pmc_clk_is_enabled,
>>>>>>>> +    .enable = pmc_clk_enable,
>>>>>>>> +    .disable = pmc_clk_disable,
>>>>>>>> +};
>>>>>>>> +
>>>>>>>> +static struct clk *
>>>>>>>> +tegra_pmc_clk_out_register(const struct pmc_clk_init_data *data,
>>>>>>>> +               unsigned long offset)
>>>>>>>> +{
>>>>>>>> +    struct clk_init_data init;
>>>>>>>> +    struct pmc_clk *pmc_clk;
>>>>>>>> +
>>>>>>>> +    pmc_clk = kzalloc(sizeof(*pmc_clk), GFP_KERNEL);
>>>>>>>> +    if (!pmc_clk)
>>>>>>>> +        return ERR_PTR(-ENOMEM);
>>>>>>>> +
>>>>>>>> +    init.name = data->name;
>>>>>>>> +    init.ops = &pmc_clk_ops;
>>>>>>>> +    init.parent_names = data->parents;
>>>>>>>> +    init.num_parents = data->num_parents;
>>>>>>>> +    init.flags = CLK_SET_RATE_NO_REPARENT | CLK_SET_RATE_PARENT |
>>>>>>>> +             CLK_SET_PARENT_GATE;
>>>>>>>> +
>>>>>>>> +    pmc_clk->hw.init = &init;
>>>>>>>> +    pmc_clk->offs = offset;
>>>>>>>> +    pmc_clk->mux_mask = 3;
>>>>>>> If mux_mask is a constant value, perhaps will be better to
>>>>>>> replace the
>>>>>>> variable with a literal?
>>>>>>>
>>>>>>> #define PMC_CLK_OUT_MUX_MASK    GENMASK(1, 0)
>>>>>> Maybe even:
>>>>>>
>>>>>> #define PMC_CLK_OUT_MUX_MASK(c)    GENMASK(c->shift + 1, c->shift)
>>>> MUX Mask is used only here for PMC clock out and is same for all
>>>> clk_out mux so will use
>>>>
>>>> #define PMC_CLK_OUT_MUX_MASK    GENMASK(1, 0)
>>>>
>>>>> I want to point out that may be a separated gate/mux shifts is a fine
>>>>> variant, you should try and see whether another variants produce more
>>>>> concise result.
>>>>>
>>>>> [snip]
>>> We can do mux_shift as gate_shift + 4 and that restricts this clk
>>> register only for clk1/2/3 as well and there are no other clocks in pmc
>>> anyway.
>>>
>>> How about using bit shift define for CLK1, CLK2, and CLK3?
>>>
>>> .mux_shift = PMC_CLK1_SRC_SEL_SHIFT,
>>>
>>> .gate_shift = PMC_CLK1_FORCE_EN_SHIFT,
>>>
>>>
>> I think that just renaming ".gate_shift" -> ".force_en_shift" should be
>> good enough.
> You meant to assign bit position directly instead of defines like what I
> have now in v4 and use force_en_shift instead of gate_shift?

Yes

  reply	other threads:[~2019-12-20  4:34 UTC|newest]

Thread overview: 54+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-17 20:03 [PATCH v4 00/19] Move PMC clocks into Tegra PMC driver Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 01/19] dt-bindings: clock: tegra: Change CLK_M_DIV to OSC_DIV clocks Sowjanya Komatineni
2019-12-18 21:19   ` Rob Herring
2019-12-17 20:03 ` [PATCH v4 02/19] clk: tegra: Change CLK_M_DIV clocks " Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 03/19] clk: tegra: Fix Tegra PMC clock out parents Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 04/19] dt-bindings: tegra: Convert Tegra PMC bindings to YAML Sowjanya Komatineni
2019-12-18 21:29   ` Rob Herring
2019-12-18 22:31     ` Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 05/19] dt-bindings: soc: tegra-pmc: Add Tegra PMC clock bindings Sowjanya Komatineni
2019-12-18  7:56   ` Dmitry Osipenko
2019-12-17 20:03 ` [PATCH v4 06/19] soc: tegra: Add Tegra PMC clock registrations into PMC driver Sowjanya Komatineni
2019-12-18  8:30   ` Dmitry Osipenko
2019-12-18  8:35     ` Dmitry Osipenko
2019-12-18 15:46       ` Sowjanya Komatineni
2019-12-18 15:50         ` Sowjanya Komatineni
2019-12-18 16:52           ` Dmitry Osipenko
2019-12-18 17:00             ` Sowjanya Komatineni
2019-12-18 16:48         ` Dmitry Osipenko
2019-12-18 21:44       ` Dmitry Osipenko
2019-12-19  0:41         ` Sowjanya Komatineni
2019-12-20  1:21           ` Sowjanya Komatineni
2019-12-20  1:39             ` Dmitry Osipenko
2019-12-20  4:13               ` Sowjanya Komatineni
2019-12-20  4:34                 ` Dmitry Osipenko [this message]
2019-12-20 19:06                   ` Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 07/19] dt-bindings: soc: tegra-pmc: Add id for Tegra PMC 32KHz blink clock Sowjanya Komatineni
2019-12-18 21:30   ` Rob Herring
2019-12-17 20:03 ` [PATCH v4 08/19] soc: tegra: Add support for " Sowjanya Komatineni
2019-12-18  5:08   ` Dmitry Osipenko
2019-12-17 20:03 ` [PATCH v4 09/19] clk: tegra: Remove tegra_pmc_clk_init along with clk ids Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 10/19] dt-bindings: clock: tegra: Remove pmc clock ids from clock dt-bindings Sowjanya Komatineni
2019-12-18 21:32   ` Rob Herring
2019-12-17 20:03 ` [PATCH v4 11/19] ASoC: tegra: Use device managed resource APIs to get the clock Sowjanya Komatineni
2019-12-17 20:03 ` [PATCH v4 12/19] ASoC: tegra: Add initial parent configuration for audio mclk Sowjanya Komatineni
2019-12-17 20:04 ` [PATCH v4 13/19] ASoC: tegra: Add fallback implementation " Sowjanya Komatineni
2019-12-18  6:59   ` Dmitry Osipenko
2019-12-18  7:01     ` Dmitry Osipenko
2019-12-18  7:14       ` Sowjanya Komatineni
2019-12-18  7:22         ` Dmitry Osipenko
2019-12-18  7:31           ` Dmitry Osipenko
2019-12-18 15:43             ` Sowjanya Komatineni
2019-12-18 16:29               ` Dmitry Osipenko
2019-12-18 16:32                 ` Sowjanya Komatineni
2019-12-18 16:34                   ` Dmitry Osipenko
2019-12-17 20:04 ` [PATCH v4 14/19] clk: tegra: Remove audio related clock enables from clocks init_table Sowjanya Komatineni
2019-12-17 20:04 ` [PATCH v4 15/19] ARM: dts: tegra: Add clock-cells property to pmc Sowjanya Komatineni
2019-12-18 21:36   ` Dmitry Osipenko
2019-12-17 20:04 ` [PATCH v4 16/19] arm64: tegra: Add clock-cells property to Tegra PMC node Sowjanya Komatineni
2019-12-17 20:04 ` [PATCH v4 17/19] ARM: tegra: Update sound node clocks in device tree Sowjanya Komatineni
2019-12-18  6:39   ` Dmitry Osipenko
2019-12-18  7:47   ` Dmitry Osipenko
2019-12-17 20:04 ` [PATCH v4 18/19] arm64: tegra: smaug: Change clk_out_2 provider to pmc Sowjanya Komatineni
2019-12-17 20:04 ` [PATCH v4 19/19] ASoC: nau8825: change Tegra clk_out_2 provider from tegra_car " Sowjanya Komatineni
2019-12-18 21:32   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=42f39288-da11-e28d-2a0e-28f1b020e674@gmail.com \
    --to=digetx@gmail.com \
    --cc=daniel.lezcano@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=jonathanh@nvidia.com \
    --cc=josephl@nvidia.com \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-tegra@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=markz@nvidia.com \
    --cc=mmaddireddy@nvidia.com \
    --cc=mperttunen@nvidia.com \
    --cc=pdeschrijver@nvidia.com \
    --cc=pgaikwad@nvidia.com \
    --cc=robh+dt@kernel.org \
    --cc=sboyd@kernel.org \
    --cc=skomatineni@nvidia.com \
    --cc=spujar@nvidia.com \
    --cc=thierry.reding@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).