From: Jerome Brunet <jbrunet@baylibre.com>
To: Jianxin Pan <jianxin.pan@amlogic.com>,
Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>,
Carlo Caione <carlo@caione.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Boris Brezillon <boris.brezillon@bootlin.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Yixun Lan <yixun.lan@amlogic.com>,
Liang Yang <liang.yang@amlogic.com>,
Jian Hu <jian.hu@amlogic.com>,
Qiufang Dai <qiufang.dai@amlogic.com>,
Hanjie Lin <hanjie.lin@amlogic.com>,
Victor Wan <victor.wan@amlogic.com>,
linux-clk@vger.kernel.org, linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH RESEND v7 4/4] clk: meson: add one based divider support for sclk divider
Date: Tue, 11 Dec 2018 18:16:53 +0100 [thread overview]
Message-ID: <4da764c237b8f752af1dc33a011e2a4b73068f02.camel@baylibre.com> (raw)
In-Reply-To: <1544457877-51301-5-git-send-email-jianxin.pan@amlogic.com>
On Tue, 2018-12-11 at 00:04 +0800, Jianxin Pan wrote:
> When CLK_DIVIDER_ONE_BASED flag is set, the sclk divider will be:
> one based divider (div = val), and zero value gates the clock
>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
> ---
> drivers/clk/meson/clkc-audio.h | 1 +
> drivers/clk/meson/sclk-div.c | 28 ++++++++++++++++++----------
> 2 files changed, 19 insertions(+), 10 deletions(-)
Such a patch should be done earlier in the series, at least before using sclk
in your controller, otherwise thing will be broken in between
In general, I would prefer if you had added two helper function to deal with
the translation between register value and divider value.
Only these function should care about CLK_DIVIDER_ONE_BASED, the rest should
just call them.
This, we will be able to deal the with HI (duty cycle) part as well, which you
completly skiped.
I know your device does not have this, but still the code has to make sense.
>
> diff --git a/drivers/clk/meson/clkc-audio.h b/drivers/clk/meson/clkc-audio.h
> index 0a7c157..9bd6ced 100644
> --- a/drivers/clk/meson/clkc-audio.h
> +++ b/drivers/clk/meson/clkc-audio.h
> @@ -20,6 +20,7 @@ struct meson_sclk_div_data {
> struct parm hi;
> unsigned int cached_div;
> struct clk_duty cached_duty;
> + u8 flags;
> };
>
> extern const struct clk_ops meson_clk_triphase_ops;
> diff --git a/drivers/clk/meson/sclk-div.c b/drivers/clk/meson/sclk-div.c
> index bc64019..d98707b 100644
> --- a/drivers/clk/meson/sclk-div.c
> +++ b/drivers/clk/meson/sclk-div.c
> @@ -24,22 +24,23 @@
> return (struct meson_sclk_div_data *)clk->data;
> }
>
> -static int sclk_div_maxval(struct meson_sclk_div_data *sclk)
> -{
> - return (1 << sclk->div.width) - 1;
> -}
> -
> static int sclk_div_maxdiv(struct meson_sclk_div_data *sclk)
> {
> - return sclk_div_maxval(sclk) + 1;
> + if (sclk->flags & CLK_DIVIDER_ONE_BASED)
> + return clk_div_mask(sclk->div.width);
> + else
> + return clk_div_mask(sclk->div.width) + 1;
seems over complicated.
why no call clk_div_mask just once, and add 1 if necessary ?
> }
>
> static int sclk_div_getdiv(struct clk_hw *hw, unsigned long rate,
> unsigned long prate, int maxdiv)
> {
> int div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
> + struct clk_regmap *clk = to_clk_regmap(hw);
> + struct meson_sclk_div_data *sclk = meson_sclk_div_data(clk);
> + int mindiv = (sclk->flags & CLK_DIVIDER_ONE_BASED) ? 1 : 2;
This is why I want helpers, don't like this above
>
> - return clamp(div, 2, maxdiv);
> + return clamp(div, mindiv, maxdiv);
> }
>
> static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
> @@ -47,7 +48,7 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
> long rate,
> struct meson_sclk_div_data *sclk)
> {
> struct clk_hw *parent = clk_hw_get_parent(hw);
> - int bestdiv = 0, i;
> + int bestdiv = 0, i, mindiv;
> unsigned long maxdiv, now, parent_now;
> unsigned long best = 0, best_parent = 0;
>
> @@ -64,8 +65,9 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
> long rate,
> * unsigned long in rate * i below
> */
> maxdiv = min(ULONG_MAX / rate, maxdiv);
> + mindiv = (sclk->flags & CLK_DIVIDER_ONE_BASED) ? 1 : 2;
>
> - for (i = 2; i <= maxdiv; i++) {
> + for (i = mindiv; i <= maxdiv; i++) {
> /*
> * It's the most ideal case if the requested rate can be
> * divided from parent clock without needing to change
> @@ -153,10 +155,14 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
> static void sclk_apply_divider(struct clk_regmap *clk,
> struct meson_sclk_div_data *sclk)
> {
> + unsigned int div;
> +
> if (MESON_PARM_APPLICABLE(&sclk->hi))
> sclk_apply_ratio(clk, sclk);
>
> - meson_parm_write(clk->map, &sclk->div, sclk->cached_div - 1);
> + div = (sclk->flags & CLK_DIVIDER_ONE_BASED) ?
> + sclk->cached_div : (sclk->cached_div - 1);
helpers again.
> + meson_parm_write(clk->map, &sclk->div, div);
> }
>
> static int sclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
> @@ -223,6 +229,8 @@ static void sclk_div_init(struct clk_hw *hw)
> /* if the divider is initially disabled, assume max */
> if (!val)
> sclk->cached_div = sclk_div_maxdiv(sclk);
> + else if (sclk->flags & CLK_DIVIDER_ONE_BASED)
> + sclk->cached_div = val;
> else
> sclk->cached_div = val + 1;
same ...
>
next prev parent reply other threads:[~2018-12-11 17:17 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-10 16:04 [PATCH RESEND v7 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
2018-12-10 16:04 ` [PATCH RESEND v7 1/4] clk: meson: add emmc sub clock phase delay driver Jianxin Pan
2018-12-11 16:28 ` Jerome Brunet
2018-12-13 4:42 ` Jianxin Pan
2018-12-10 16:04 ` [PATCH RESEND v7 2/4] clk: meson: add DT documentation for emmc clock controller Jianxin Pan
2018-12-10 16:04 ` [PATCH RESEND v7 3/4] clk: meson: add sub MMC clock controller driver Jianxin Pan
2018-12-11 16:59 ` Jerome Brunet
2018-12-13 4:55 ` Jianxin Pan
2018-12-13 9:01 ` Jerome Brunet
2018-12-14 4:19 ` Jianxin Pan
2018-12-10 16:04 ` [PATCH RESEND v7 4/4] clk: meson: add one based divider support for sclk divider Jianxin Pan
2018-12-11 17:16 ` Jerome Brunet [this message]
2018-12-13 8:03 ` Jianxin Pan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4da764c237b8f752af1dc33a011e2a4b73068f02.camel@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=boris.brezillon@bootlin.com \
--cc=carlo@caione.org \
--cc=hanjie.lin@amlogic.com \
--cc=jian.hu@amlogic.com \
--cc=jianxin.pan@amlogic.com \
--cc=khilman@baylibre.com \
--cc=liang.yang@amlogic.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=miquel.raynal@bootlin.com \
--cc=mturquette@baylibre.com \
--cc=narmstrong@baylibre.com \
--cc=qiufang.dai@amlogic.com \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=victor.wan@amlogic.com \
--cc=yixun.lan@amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).