From: Jianxin Pan <jianxin.pan@amlogic.com>
To: Jerome Brunet <jbrunet@baylibre.com>,
Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>,
Carlo Caione <carlo@caione.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Boris Brezillon <boris.brezillon@bootlin.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
Yixun Lan <yixun.lan@amlogic.com>,
Liang Yang <liang.yang@amlogic.com>,
Jian Hu <jian.hu@amlogic.com>,
Qiufang Dai <qiufang.dai@amlogic.com>,
Hanjie Lin <hanjie.lin@amlogic.com>,
Victor Wan <victor.wan@amlogic.com>, <linux-clk@vger.kernel.org>,
<linux-amlogic@lists.infradead.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>
Subject: Re: [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider
Date: Thu, 24 Jan 2019 17:10:47 +0800 [thread overview]
Message-ID: <609bae99-03d4-c338-a594-efae037ebac7@amlogic.com> (raw)
In-Reply-To: <024e1206ad8c103ef67a72fb2a48cdd5ec634a12.camel@baylibre.com>
Hi Jerome,
On 2019/1/22 17:25, Jerome Brunet wrote:
> On Tue, 2019-01-08 at 21:50 +0800, Jianxin Pan wrote:
>> When CLK_DIVIDER_ONE_BASED flag is set, the sclk divider will be:
>> one based divider (div = val), and zero value gates the clock
>>
>> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
>> ---
>> drivers/clk/meson/Makefile | 3 ++-
>> drivers/clk/meson/clkc-audio.h | 8 ------
>> drivers/clk/meson/clkc.h | 10 ++++++-
>> drivers/clk/meson/sclk-div.c | 59 ++++++++++++++++++++++++++++-----------
>> ---
>> 4 files changed, 50 insertions(+), 30 deletions(-)
>>
>> diff --git a/drivers/clk/meson/Makefile b/drivers/clk/meson/Makefile
>> index a849aa8..acd8694 100644
>> --- a/drivers/clk/meson/Makefile
>> +++ b/drivers/clk/meson/Makefile
>> @@ -4,7 +4,8 @@
>>
>> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-pll.o clk-mpll.o clk-phase.o vid-
>> pll-div.o
>> obj-$(CONFIG_COMMON_CLK_AMLOGIC) += clk-input.o
>> -obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o sclk-div.o
>> +obj-$(CONFIG_COMMON_CLK_AMLOGIC) += sclk-div.o
>> +obj-$(CONFIG_COMMON_CLK_AMLOGIC_AUDIO) += clk-triphase.o
>> obj-$(CONFIG_COMMON_CLK_MESON_AO) += meson-aoclk.o
>> obj-$(CONFIG_COMMON_CLK_MESON8B) += meson8b.o
>> obj-$(CONFIG_COMMON_CLK_GXBB) += gxbb.o gxbb-aoclk.o gxbb-aoclk-
>> 32k.o
>> diff --git a/drivers/clk/meson/clkc-audio.h b/drivers/clk/meson/clkc-audio.h
>> index 0a7c157..286ff12 100644
>> --- a/drivers/clk/meson/clkc-audio.h
>> +++ b/drivers/clk/meson/clkc-audio.h
>> @@ -15,14 +15,6 @@ struct meson_clk_triphase_data {
>> struct parm ph2;
>> };
>>
>> -struct meson_sclk_div_data {
>> - struct parm div;
>> - struct parm hi;
>> - unsigned int cached_div;
>> - struct clk_duty cached_duty;
>> -};
>> -
>> extern const struct clk_ops meson_clk_triphase_ops;
>> -extern const struct clk_ops meson_sclk_div_ops;
>>
>> #endif /* __MESON_CLKC_AUDIO_H */
>> diff --git a/drivers/clk/meson/clkc.h b/drivers/clk/meson/clkc.h
>> index 6183b22..00b3320 100644
>> --- a/drivers/clk/meson/clkc.h
>> +++ b/drivers/clk/meson/clkc.h
>> @@ -27,6 +27,14 @@ struct parm {
>> u8 width;
>> };
>>
>> +struct meson_sclk_div_data {
>> + struct parm div;
>> + struct parm hi;
>> + unsigned int cached_div;
>> + struct clk_duty cached_duty;
>> + u8 flags;
>> +};
>> +
>> static inline unsigned int meson_parm_read(struct regmap *map, struct parm
>> *p)
>> {
>> unsigned int val;
>> @@ -118,10 +126,10 @@ struct clk_regmap _name = {
>> \
>> extern const struct clk_ops meson_clk_mpll_ops;
>> extern const struct clk_ops meson_clk_phase_ops;
>> extern const struct clk_ops meson_vid_pll_div_ro_ops;
>> +extern const struct clk_ops meson_sclk_div_ops;
>>
>> struct clk_hw *meson_clk_hw_register_input(struct device *dev,
>> const char *of_name,
>> const char *clk_name,
>> unsigned long flags);
>> -
>> #endif /* __CLKC_H */
>> diff --git a/drivers/clk/meson/sclk-div.c b/drivers/clk/meson/sclk-div.c
>> index bc64019..a6c425b 100644
>> --- a/drivers/clk/meson/sclk-div.c
>> +++ b/drivers/clk/meson/sclk-div.c
>> @@ -4,42 +4,60 @@
>> * Author: Jerome Brunet <jbrunet@baylibre.com>
>> *
>> * Sample clock generator divider:
>> - * This HW divider gates with value 0 but is otherwise a zero based
>> divider:
>> + * This HW divider gates with value 0
>> *
>> * val >= 1
>> - * divider = val + 1
>> + * divider = val + 1 if ONE_BASED is not set, otherwise divider = val.
>> *
>> * The duty cycle may also be set for the LR clock variant. The duty cycle
>> * ratio is:
>> *
>> * hi = [0 - val]
>> - * duty_cycle = (1 + hi) / (1 + val)
>> + * duty_cycle = (1 + hi) / (1 + val) if ONE_BASED is not set, otherwise:
>> + * duty_cycle = hi / (1 + val)
>> */
>>
>> -#include "clkc-audio.h"
>> +#include "clkc.h"
>>
>> -static inline struct meson_sclk_div_data *
>> -meson_sclk_div_data(struct clk_regmap *clk)
>> +static inline int get_reg(int val, unsigned char flag)
>
> s/get_reg/sclk_get_reg
OK, I will rename get_reg and get_value in next version.
Thank you for the review.
>
>> {
>> - return (struct meson_sclk_div_data *)clk->data;
>> + WARN_ON(val < 1);
>
> I don't think this WARN is justified, especially since you are using this
> function to set the hi value.
OK, it will remove it. Thank you.
>
>> + if ((flag & CLK_DIVIDER_ONE_BASED) || !val)
>
> I don't like that you make a dependency on the generic divider just for this.
> Please make your own flag like MESON_SCLK_ONE_BASED
OK, I will define a new flag MESON_SCLK_ONE_BASED in drivers/clk/meson/clkc.h.
>
>> + return val;
>> + else
>> + return val - 1;
>> +}
>> +
>> +static inline int get_value(int reg, unsigned char flag)
>
> s/get_value/sclk_get_divider
OK, I will rename it.
>
>> +{
>> + if (flag & CLK_DIVIDER_ONE_BASED)
>> + return reg;
>> + else
>> + return reg + 1;
>> }
>>
>> -static int sclk_div_maxval(struct meson_sclk_div_data *sclk)
>> +static inline struct meson_sclk_div_data *
>> +meson_sclk_div_data(struct clk_regmap *clk)
>> {
>> - return (1 << sclk->div.width) - 1;
>> + return (struct meson_sclk_div_data *)clk->data;
>> }
>>
>> static int sclk_div_maxdiv(struct meson_sclk_div_data *sclk)
>> {
>> - return sclk_div_maxval(sclk) + 1;
>> + unsigned int reg = clk_div_mask(sclk->div.width);
>
> same here, leave the generic divider alone.
>
> `(1 << sclk->div.width) - 1` was fine to get max register value.
>
>> +
>> + return get_value(reg, sclk->flags);
>> }
>>
>> static int sclk_div_getdiv(struct clk_hw *hw, unsigned long rate,
>> unsigned long prate, int maxdiv)
>> {
>> int div = DIV_ROUND_CLOSEST_ULL((u64)prate, rate);
>> + struct clk_regmap *clk = to_clk_regmap(hw);
>> + struct meson_sclk_div_data *sclk = meson_sclk_div_data(clk);
>> + int mindiv = get_value(1, sclk->flags);
>
> maxdiv is provided as a param while mindiv is computed inside this function.
> let's be coherent and pick one approach.
OK, I will compute min and max in this function both.
Thank you for your review.
>
>>
>> - return clamp(div, 2, maxdiv);
>> + return clamp(div, mindiv, maxdiv);
>> }
>>
>> static int sclk_div_bestdiv(struct clk_hw *hw, unsigned long rate,
>> @@ -47,7 +65,7 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
>> long rate,
>> struct meson_sclk_div_data *sclk)
>> {
>> struct clk_hw *parent = clk_hw_get_parent(hw);
>> - int bestdiv = 0, i;
>> + int bestdiv = 0, i, mindiv;
>> unsigned long maxdiv, now, parent_now;
>> unsigned long best = 0, best_parent = 0;
>>
>> @@ -64,8 +82,9 @@ static int sclk_div_bestdiv(struct clk_hw *hw, unsigned
>> long rate,
>> * unsigned long in rate * i below
>> */
>> maxdiv = min(ULONG_MAX / rate, maxdiv);
>> + mindiv = get_value(1, sclk->flags);
>>
>> - for (i = 2; i <= maxdiv; i++) {
>> + for (i = mindiv; i <= maxdiv; i++) {
>> /*
>> * It's the most ideal case if the requested rate can be
>> * divided from parent clock without needing to change
>> @@ -111,10 +130,7 @@ static void sclk_apply_ratio(struct clk_regmap *clk,
>> sclk->cached_duty.num,
>> sclk->cached_duty.den);
>>
>> - if (hi)
>> - hi -= 1;
>> -
>> - meson_parm_write(clk->map, &sclk->hi, hi);
>> + meson_parm_write(clk->map, &sclk->hi, get_reg(hi, sclk->flags));
>> }
>>
>> static int sclk_div_set_duty_cycle(struct clk_hw *hw,
>> @@ -145,7 +161,7 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
>> }
>>
>> hi = meson_parm_read(clk->map, &sclk->hi);
>> - duty->num = hi + 1;
>> + duty->num = get_value(hi, sclk->flags);
>> duty->den = sclk->cached_div;
>> return 0;
>> }
>> @@ -153,10 +169,13 @@ static int sclk_div_get_duty_cycle(struct clk_hw *hw,
>> static void sclk_apply_divider(struct clk_regmap *clk,
>> struct meson_sclk_div_data *sclk)
>> {
>> + unsigned int div;
>> +
>> if (MESON_PARM_APPLICABLE(&sclk->hi))
>> sclk_apply_ratio(clk, sclk);
>>
>> - meson_parm_write(clk->map, &sclk->div, sclk->cached_div - 1);
>> + div = get_reg(sclk->cached_div, sclk->flags);
>> + meson_parm_write(clk->map, &sclk->div, div);
>> }
>>
>> static int sclk_div_set_rate(struct clk_hw *hw, unsigned long rate,
>> @@ -224,7 +243,7 @@ static void sclk_div_init(struct clk_hw *hw)
>> if (!val)
>> sclk->cached_div = sclk_div_maxdiv(sclk);
>> else
>> - sclk->cached_div = val + 1;
>> + sclk->cached_div = get_value(val, sclk->flags);
>>
>> sclk_div_get_duty_cycle(hw, &sclk->cached_duty);
>> }
>
>
> .
>
next prev parent reply other threads:[~2019-01-24 9:10 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-08 13:50 [PATCH RESEND v9 0/4] clk: meson: add a sub EMMC clock controller support Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 1/4] clk: meson: add one based divider support for sclk divider Jianxin Pan
2019-01-22 9:25 ` Jerome Brunet
2019-01-24 9:10 ` Jianxin Pan [this message]
2019-01-08 13:50 ` [PATCH v9 2/4] clk: meson: add emmc sub clock phase delay driver Jianxin Pan
2019-01-08 13:50 ` [PATCH v9 3/4] clk: meson: add DT documentation for emmc clock controller Jianxin Pan
2019-01-22 9:27 ` Jerome Brunet
2019-01-08 13:50 ` [PATCH v9 4/4] clk: meson: add sub MMC clock controller driver Jianxin Pan
2019-01-22 9:25 ` Jerome Brunet
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=609bae99-03d4-c338-a594-efae037ebac7@amlogic.com \
--to=jianxin.pan@amlogic.com \
--cc=boris.brezillon@bootlin.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=hanjie.lin@amlogic.com \
--cc=jbrunet@baylibre.com \
--cc=jian.hu@amlogic.com \
--cc=khilman@baylibre.com \
--cc=liang.yang@amlogic.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=martin.blumenstingl@googlemail.com \
--cc=miquel.raynal@bootlin.com \
--cc=mturquette@baylibre.com \
--cc=narmstrong@baylibre.com \
--cc=qiufang.dai@amlogic.com \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=victor.wan@amlogic.com \
--cc=yixun.lan@amlogic.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).