From: Tero Kristo <t-kristo@ti.com>
To: Rob Herring <robh@kernel.org>, Vignesh Raghavendra <vigneshr@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
Santosh Shilimkar <ssantosh@kernel.org>,
<linux-clk@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, Nishanth Menon <nm@ti.com>,
Linux ARM Mailing List <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH 1/2] dt-bindings: clock: Add binding documentation for TI syscon gate clock
Date: Wed, 3 Apr 2019 12:30:05 +0300 [thread overview]
Message-ID: <a998b977-99ef-876e-a226-4f1738392f9f@ti.com> (raw)
In-Reply-To: <20190328123142.GA6229@bogus>
On 28/03/2019 14:31, Rob Herring wrote:
> On Tue, Mar 12, 2019 at 02:35:17PM +0530, Vignesh Raghavendra wrote:
>> Add dt bindings for TI syscon gate clock.
>>
>> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
>> ---
>> .../bindings/clock/ti,syscon-gate-clock.txt | 35 +++++++++++++++++++
>> 1 file changed, 35 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/clock/ti,syscon-gate-clock.txt
>>
>> diff --git a/Documentation/devicetree/bindings/clock/ti,syscon-gate-clock.txt b/Documentation/devicetree/bindings/clock/ti,syscon-gate-clock.txt
>> new file mode 100644
>> index 000000000000..f2bc4281ddba
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/ti,syscon-gate-clock.txt
>> @@ -0,0 +1,35 @@
>> +TI syscon gate clock
>> +
>> +The gate clock node must be provided inside a system controller node.
>> +
>> +Required:
>> +- comaptible: Must be "ti,syscon-gate-clock"
>> +- reg: Offset of register that controls the clock within syscon regmap
>> +- ti,clock-bit-idx: bit index that control gate/ungating of clock
>> +- clocks: phandle to the clock parent
>> +- #clock-cells: must be <0>
>> +
>> +Example:
>> + ctrlmmr_epwm_ctrl: syscon@104140{
>> + compatible = "syscon", "simple-bus";
>
> Can't be both of these...
Is this a hard requirement? We seem to have few instances in the various
DTS files for various vendors where this is done, syscon is paired with
simple-mfd or simple-bus, or something else.
Basically, syscon by itself does not probe its children, and you can't
have the simple syscon support from kernel side if you don't have the
syscon compatible. Alternative is that we don't add any of the syscon
children under the syscon but add them as separate nodes outside it.
The above is not an issue for this patch itself if we ditch the separate
clock nodes, but it is more of a question about the syscon functionality
itself.
-Tero
>
>> + reg = <0x0 0x104140 0x0 0x18>;
>> + ranges = <0x0 0x0 0x104140>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ehrpwm0_tbclk: clk@0 {
>> + compatible = "ti,syscon-gate-clock";
>> + reg = <0x0>;
>> + #clock-cells = <0>;
>> + clocks = <&k3_clks 40 0>;
>> + ti,clock-bit-idx = <0>;
>
> This would imply you have multiple nodes at one address which is
> discouraged.
>
>> + };
>
> We generally don't describe clocks as 1 clock per node. Give the parent
> a specific compatible and make it a clock provider.
>
>> +
>> + ehrpwm1_tbclk: clk@4 {
>> + compatible = "ti,syscon-gate-clock";
>> + reg = <0x4>;
>> + #clock-cells = <0>;
>> + clocks = <&k3_clks 41 0>;
>> + ti,clock-bit-idx = <0>;
>> + };
>> + };
>> --
>> 2.21.0
>>
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
next prev parent reply other threads:[~2019-04-03 9:31 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-12 9:05 [PATCH 0/2] clk: keystone: Add new driver to handle syscon based clock Vignesh Raghavendra
2019-03-12 9:05 ` [PATCH 1/2] dt-bindings: clock: Add binding documentation for TI syscon gate clock Vignesh Raghavendra
2019-03-28 12:31 ` Rob Herring
2019-04-03 9:30 ` Tero Kristo [this message]
2019-04-09 7:57 ` Vignesh Raghavendra
2019-03-12 9:05 ` [PATCH 2/2] clk: keystone: Add new driver to handle syscon based clock Vignesh Raghavendra
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a998b977-99ef-876e-a226-4f1738392f9f@ti.com \
--to=t-kristo@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=nm@ti.com \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=ssantosh@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).