From: Krzysztof Kozlowski <krzk@kernel.org>
To: Kukjin Kim <kgene@kernel.org>,
Krzysztof Kozlowski <k.kozlowski@samsung.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Marek Szyprowski <m.szyprowski@samsung.com>,
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>,
Sylwester Nawrocki <s.nawrocki@samsung.com>,
Tomasz Figa <tomasz.figa@gmail.com>,
Arnd Bergmann <arnd@arndb.de>, Olof Johansson <olof@lixom.net>,
Kevin Hilman <khilman@kernel.org>,
Chanwoo Choi <cw00.choi@samsung.com>,
Inki Dae <inki.dae@samsung.com>,
Javier Martinez Canillas <javier@osg.samsung.com>,
Krzysztof Kozlowski <krzk@kernel.org>
Subject: [RFC PATCH 00/12] ARM: dts: exynos: Reorganize before adding Odroid XU board
Date: Tue, 3 May 2016 19:52:17 +0200 [thread overview]
Message-ID: <1462297949-13824-1-git-send-email-krzk@kernel.org> (raw)
Hi,
I am in the middle (or beginning) of adding DTS for Odroid XU. This
patchset is a preparation for that. I still did not figure out two
things:
1. clock IDs, should we follow Exynos5420 (or maybe reuse entirely?)
see patch 1.
2. sd0_rclk - see patch 5.
The Odroid XU board is based on Exynos5410: an octal-core design where
apparently only one cluster (big or little) could be active. The Exynos5410
is a first big.LITTLE design... with its early child issues (naughty kid).
The board itself is a mix between Odroid U3 (based on Exynos4412) and XU3.
For example it has usb3503+smsc95xx LAN as Odroid U3 so probably
same issues as U3 will happen (USB/LAN fails after TFTP boot). On the
other hand it has size, look (case) and most of components the same
as in XU3 and XU3-lite.
As for now you can boot it with Hardkernel U-Boot and SMDK5410 DTB.
Comments welcome!
BR,
Krzysztof
Krzysztof Kozlowski (12):
dt-bindings: clock: Add license and reformat Exynos5410 clock IDs
dt-bindings: clock: Add PWM clock ID to Exynos5410
ARM: dts: exynos: Re-order alphabetically Exynos5420 SD0/SD1 pinctrl
nodes
ARM: dts: exynos: Use lowercase for Exynos5410 CPU node labels
ARM: dts: exynos: Configure Exynos5410 pinctrl for eMMC and SD card
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in
exynos5410.dtsi
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Enable UART3 on Exynos5410
arch/arm/boot/dts/exynos5.dtsi | 171 +-
arch/arm/boot/dts/exynos5250-snow-common.dtsi | 2 +-
arch/arm/boot/dts/exynos5250.dtsi | 1718 ++++++++++---------
arch/arm/boot/dts/exynos5410-pinctrl.dtsi | 87 +
arch/arm/boot/dts/exynos5410-smdk5410.dts | 6 +-
arch/arm/boot/dts/exynos5410.dtsi | 112 +-
arch/arm/boot/dts/exynos5420-pinctrl.dtsi | 12 +-
arch/arm/boot/dts/exynos5420.dtsi | 2058 +++++++++++------------
arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts | 35 +-
arch/arm/boot/dts/exynos5422-odroidxu3.dts | 35 +-
arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi | 50 +
include/dt-bindings/clock/exynos5410.h | 56 +-
12 files changed, 2197 insertions(+), 2145 deletions(-)
create mode 100644 arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi
--
2.5.0
next reply other threads:[~2016-05-03 17:52 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-03 17:52 Krzysztof Kozlowski [this message]
2016-05-03 17:52 ` [RFC PATCH 01/12] dt-bindings: clock: Add license and reformat Exynos5410 clock IDs Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 02/12] dt-bindings: clock: Add PWM clock ID to Exynos5410 Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 03/12] ARM: dts: exynos: Re-order alphabetically Exynos5420 SD0/SD1 pinctrl nodes Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 04/12] ARM: dts: exynos: Use lowercase for Exynos5410 CPU node labels Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 05/12] ARM: dts: exynos: Configure Exynos5410 pinctrl for eMMC and SD card Krzysztof Kozlowski
2016-05-07 4:53 ` Alim Akhtar
2016-05-07 9:49 ` Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 06/12] ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 07/12] ARM: dts: exynos: Move common nodes to exynos5.dtsi Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 08/12] ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 09/12] ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 10/12] ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 11/12] ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi Krzysztof Kozlowski
2016-05-03 17:52 ` [RFC PATCH 12/12] ARM: dts: exynos: Enable UART3 on Exynos5410 Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1462297949-13824-1-git-send-email-krzk@kernel.org \
--to=krzk@kernel.org \
--cc=arnd@arndb.de \
--cc=b.zolnierkie@samsung.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=inki.dae@samsung.com \
--cc=javier@osg.samsung.com \
--cc=k.kozlowski@samsung.com \
--cc=kgene@kernel.org \
--cc=khilman@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=olof@lixom.net \
--cc=s.nawrocki@samsung.com \
--cc=tomasz.figa@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).