From: Guenter Roeck <linux@roeck-us.net>
To: Michael Walle <michael@walle.cc>,
linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-hwmon@vger.kernel.org,
linux-pwm@vger.kernel.org, linux-watchdog@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: "Linus Walleij" <linus.walleij@linaro.org>,
"Bartosz Golaszewski" <bgolaszewski@baylibre.com>,
"Rob Herring" <robh+dt@kernel.org>,
"Jean Delvare" <jdelvare@suse.com>,
"Lee Jones" <lee.jones@linaro.org>,
"Thierry Reding" <thierry.reding@gmail.com>,
"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
"Wim Van Sebroeck" <wim@linux-watchdog.org>,
"Shawn Guo" <shawnguo@kernel.org>, "Li Yang" <leoyang.li@nxp.com>,
"Thomas Gleixner" <tglx@linutronix.de>,
"Jason Cooper" <jason@lakedaemon.net>,
"Marc Zyngier" <maz@kernel.org>
Subject: Re: [PATCH 14/18] hwmon: add support for the sl28cpld hardware monitoring controller
Date: Tue, 17 Mar 2020 20:27:16 -0700 [thread overview]
Message-ID: <11700297-affd-8bdc-2414-3dc7f2b62798@roeck-us.net> (raw)
In-Reply-To: <20200317205017.28280-15-michael@walle.cc>
On 3/17/20 1:50 PM, Michael Walle wrote:
> This adds support for the hardware monitoring controller of the sl28cpld
> board management controller. This driver is part of a multi-function
> device.
>
> Signed-off-by: Michael Walle <michael@walle.cc>
> ---
> drivers/hwmon/Kconfig | 10 +++
> drivers/hwmon/Makefile | 1 +
> drivers/hwmon/sl28cpld-hwmon.c | 146 +++++++++++++++++++++++++++++++++
Please also provide Documentation/hwmon/sl28cpld.
> 3 files changed, 157 insertions(+)
> create mode 100644 drivers/hwmon/sl28cpld-hwmon.c
>
> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
> index 05a30832c6ba..c98716f78cfa 100644
> --- a/drivers/hwmon/Kconfig
> +++ b/drivers/hwmon/Kconfig
> @@ -1412,6 +1412,16 @@ config SENSORS_RASPBERRYPI_HWMON
> This driver can also be built as a module. If so, the module
> will be called raspberrypi-hwmon.
>
> +config SENSORS_SL28CPLD
> + tristate "Kontron's SMARC-sAL28 hardware monitoring driver"
> + depends on MFD_SL28CPLD
> + help
> + If you say yes here you get support for a fan connected to the
> + input of the SMARC connector of Kontron's SMARC-sAL28 module.
> +
> + This driver can also be built as a module. If so, the module
> + will be called sl28cpld-hwmon.
> +
> config SENSORS_SHT15
> tristate "Sensiron humidity and temperature sensors. SHT15 and compat."
> depends on GPIOLIB || COMPILE_TEST
> diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
> index b0b9c8e57176..dfb0f8cda2dd 100644
> --- a/drivers/hwmon/Makefile
> +++ b/drivers/hwmon/Makefile
> @@ -155,6 +155,7 @@ obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o
> obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o
> obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o
> obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o
> +obj-$(CONFIG_SENSORS_SL28CPLD) += sl28cpld-hwmon.o
> obj-$(CONFIG_SENSORS_SHT15) += sht15.o
> obj-$(CONFIG_SENSORS_SHT21) += sht21.o
> obj-$(CONFIG_SENSORS_SHT3x) += sht3x.o
> diff --git a/drivers/hwmon/sl28cpld-hwmon.c b/drivers/hwmon/sl28cpld-hwmon.c
> new file mode 100644
> index 000000000000..7ac42bb0a48c
> --- /dev/null
> +++ b/drivers/hwmon/sl28cpld-hwmon.c
> @@ -0,0 +1,146 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * SMARC-sAL28 fan hardware monitoring driver.
> + *
> + * Copyright 2019 Kontron Europe GmbH
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/bitfield.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_address.h>
> +#include <linux/regmap.h>
> +#include <linux/platform_device.h>
> +#include <linux/hwmon.h>
> +
Alphabetic order of include files, please.
> +#define FAN_INPUT 0
> +#define FAN_SCALE_X8 BIT(7)
> +#define FAN_VALUE_MASK GENMASK(6, 0)
> +
> +struct sl28cpld_hwmon {
> + struct regmap *regmap;
> + u32 offset;
> +};
> +
> +static umode_t sl28cpld_hwmon_is_visible(const void *data,
> + enum hwmon_sensor_types type,
> + u32 attr, int channel)
> +{
> + return 0444;
> +}
> +
> +static int sl28cpld_hwmon_read(struct device *dev,
> + enum hwmon_sensor_types type, u32 attr,
> + int channel, long *input)
> +{
> + struct sl28cpld_hwmon *hwmon = dev_get_drvdata(dev);
> + unsigned int value;
> + int ret;
> +
> + switch (attr) {
> + case hwmon_fan_input:
> + ret = regmap_read(hwmon->regmap, hwmon->offset + FAN_INPUT,
> + &value);
> + if (ret)
> + return ret;
> + /*
> + * The register has a 7 bit value and 1 bit which indicates the
> + * scale. If the MSB is set, then the lower 7 bit has to be
> + * multiplied by 8, to get the correct reading.
> + */
> + if (value & FAN_SCALE_X8)
> + value = FIELD_GET(FAN_VALUE_MASK, value) << 3;
> +
> + /*
> + * The counter period is 1000ms and the sysfs specification
> + * says we should asssume 2 pulses per revolution.
> + */
> + value *= 60 / 2;
> +
> + break;
> + default:
> + return -EOPNOTSUPP;
> + }
> +
> + *input = value;
> + return 0;
> +}
> +
> +static const u32 sl28cpld_hwmon_fan_config[] = {
> + HWMON_F_INPUT,
> + 0
> +};
> +
> +static const struct hwmon_channel_info sl28cpld_hwmon_fan = {
> + .type = hwmon_fan,
> + .config = sl28cpld_hwmon_fan_config,
> +};
> +
> +static const struct hwmon_channel_info *sl28cpld_hwmon_info[] = {
> + &sl28cpld_hwmon_fan,
> + NULL
> +};
> +
> +static const struct hwmon_ops sl28cpld_hwmon_ops = {
> + .is_visible = sl28cpld_hwmon_is_visible,
> + .read = sl28cpld_hwmon_read,
> +};
> +
> +static const struct hwmon_chip_info sl28cpld_hwmon_chip_info = {
> + .ops = &sl28cpld_hwmon_ops,
> + .info = sl28cpld_hwmon_info,
> +};
> +
> +static int sl28cpld_hwmon_probe(struct platform_device *pdev)
> +{
> + struct device *hwmon_dev;
> + struct sl28cpld_hwmon *hwmon;
> + struct resource *res;
> +
> + hwmon = devm_kzalloc(&pdev->dev, sizeof(*hwmon), GFP_KERNEL);
> + if (!hwmon)
> + return -ENOMEM;
> +
> + if (!pdev->dev.parent)
> + return -ENODEV;
> +
Maybe do this first ?
> + hwmon->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + if (!hwmon->regmap)
> + return -ENODEV;
> +
> + res = platform_get_resource(pdev, IORESOURCE_REG, 0);
> + if (!res)
> + return -EINVAL;
> + hwmon->offset = res->start;
> +
> + hwmon_dev = devm_hwmon_device_register_with_info(&pdev->dev,
> + "sl28cpld_hwmon",
> + hwmon,
> + &sl28cpld_hwmon_chip_info,
> + NULL);
> + if (IS_ERR(hwmon_dev)) {
> + dev_err(&pdev->dev, "failed to register as hwmon device");
> + return PTR_ERR(hwmon_dev);
> + }
> +
> + return 0;
> +}
> +
> +static const struct platform_device_id sl28cpld_hwmon_id_table[] = {
> + {"sl28cpld-fan", 0},
> +};
> +MODULE_DEVICE_TABLE(platform, sl28cpld_hwmon_id_table);
> +
> +static struct platform_driver sl28cpld_hwmon_driver = {
> + .probe = sl28cpld_hwmon_probe,
> + .id_table = sl28cpld_hwmon_id_table,
I'd have expected an of_match_table.
> + .driver = {
> + .name = "sl28cpld-hwmon",
> + },
> +};
> +module_platform_driver(sl28cpld_hwmon_driver);
> +
> +MODULE_DESCRIPTION("sl28cpld Hardware Monitoring Driver");
> +MODULE_LICENSE("GPL");
>
next prev parent reply other threads:[~2020-03-18 3:27 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-17 20:49 [PATCH 00/18] Add support for Kontron sl28cpld Michael Walle
2020-03-17 20:50 ` [PATCH 01/18] include/linux/ioport.h: add helper to define REG resource constructs Michael Walle
2020-03-17 20:50 ` [PATCH 02/18] mfd: mfd-core: Don't overwrite the dma_mask of the child device Michael Walle
2020-03-17 20:50 ` [PATCH 03/18] mfd: mfd-core: match device tree node against reg property Michael Walle
2020-03-17 20:50 ` [PATCH 04/18] dt-bindings: mfd: Add bindings for sl28cpld Michael Walle
2020-03-30 22:35 ` Rob Herring
2020-03-31 7:40 ` Michael Walle
2020-03-17 20:50 ` [PATCH 05/18] mfd: Add support for Kontron sl28cpld management controller Michael Walle
2020-03-18 3:28 ` Guenter Roeck
2020-03-18 16:38 ` Michael Walle
2020-03-17 20:50 ` [PATCH 06/18] irqchip: add sl28cpld interrupt controller support Michael Walle
2020-03-18 16:53 ` Guenter Roeck
2020-03-18 17:06 ` Michael Walle
2020-03-18 20:35 ` Guenter Roeck
2020-03-17 20:50 ` [PATCH 07/18] dt-bindings: watchdog: Add bindings for sl28cpld watchdog Michael Walle
2020-03-17 20:50 ` [PATCH 08/18] watchdog: add support " Michael Walle
2020-03-18 3:17 ` Guenter Roeck
2020-03-17 20:50 ` [PATCH 09/18] dt-bindings: pwm: Add bindings for sl28cpld PWM controller Michael Walle
2020-03-17 20:50 ` [PATCH 10/18] pwm: add support " Michael Walle
2020-03-17 20:50 ` [PATCH 11/18] dt-bindings: gpio: Add bindings for sl28cpld GPIO controller Michael Walle
2020-03-17 20:50 ` [PATCH 12/18] gpio: add support for the " Michael Walle
2020-03-18 9:14 ` Bartosz Golaszewski
2020-03-18 12:45 ` Michael Walle
2020-03-25 11:50 ` Bartosz Golaszewski
2020-03-26 20:05 ` Michael Walle
2020-03-27 10:20 ` Linus Walleij
2020-03-27 15:28 ` Michael Walle
2020-03-27 19:01 ` Linus Walleij
2020-03-30 11:21 ` Bartosz Golaszewski
2020-03-30 11:48 ` Michael Walle
2020-03-28 12:04 ` Michael Walle
2020-03-28 17:20 ` Michael Walle
2020-03-17 20:50 ` [PATCH 13/18] dt-bindings: hwmon: Add bindings for sl28cpld hardware monitoring Michael Walle
2020-03-17 20:50 ` [PATCH 14/18] hwmon: add support for the sl28cpld hardware monitoring controller Michael Walle
2020-03-18 3:27 ` Guenter Roeck [this message]
2020-03-18 16:32 ` Michael Walle
2020-03-17 20:50 ` [PATCH 15/18] arm64: dts: freescale: sl28: enable sl28cpld Michael Walle
2020-03-17 20:50 ` [PATCH 16/18] arm64: dts: freescale: sl28: map GPIOs to input events Michael Walle
2020-03-17 20:50 ` [PATCH 17/18] arm64: dts: freescale: sl28: enable LED support Michael Walle
2020-03-17 20:50 ` [PATCH 18/18] arm64: dts: freescale: sl28: enable fan support Michael Walle
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=11700297-affd-8bdc-2414-3dc7f2b62798@roeck-us.net \
--to=linux@roeck-us.net \
--cc=bgolaszewski@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=jason@lakedaemon.net \
--cc=jdelvare@suse.com \
--cc=lee.jones@linaro.org \
--cc=leoyang.li@nxp.com \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-hwmon@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=maz@kernel.org \
--cc=michael@walle.cc \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=tglx@linutronix.de \
--cc=thierry.reding@gmail.com \
--cc=u.kleine-koenig@pengutronix.de \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).