From: Lorenzo Bianconi <lorenzo@kernel.org>
To: jic23@kernel.org
Cc: linux-iio@vger.kernel.org, sean@geanix.com, martin@geanix.com,
rjones@gateworks.com, lorenzo.bianconi@redhat.com,
devicetree@vger.kernel.org
Subject: [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config
Date: Sun, 6 Oct 2019 15:21:57 +0200 [thread overview]
Message-ID: <873559493f99be2a659f27da293f66a546598c2b.1570367532.git.lorenzo@kernel.org> (raw)
In-Reply-To: <cover.1570367532.git.lorenzo@kernel.org>
Group irq related definition in irq_config structure in
st_lsm6dsx_settings. This is a preliminary patch to move
OpenDrain/Active low registers in st_lsm6dsx_settings.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
---
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 22 +-
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 265 ++++++++++++-------
2 files changed, 179 insertions(+), 108 deletions(-)
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
index fd02d0e184f3..873ec3b8fd69 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h
@@ -236,29 +236,21 @@ struct st_lsm6dsx_ext_dev_settings {
/**
* struct st_lsm6dsx_settings - ST IMU sensor settings
* @wai: Sensor WhoAmI default value.
- * @int1_addr: Control Register address for INT1
- * @int2_addr: Control Register address for INT2
* @reset_addr: register address for reset/reboot
* @max_fifo_size: Sensor max fifo length in FIFO words.
* @id: List of hw id/device name supported by the driver configuration.
* @channels: IIO channels supported by the device.
+ * @irq_config: interrupts related registers.
* @odr_table: Hw sensors odr table (Hz + val).
* @fs_table: Hw sensors gain table (gain + val).
* @decimator: List of decimator register info (addr + mask).
* @batch: List of FIFO batching register info (addr + mask).
- * @lir: Latched interrupt register info (addr + mask).
- * @clear_on_read: Clear on read register info (addr + mask).
* @fifo_ops: Sensor hw FIFO parameters.
* @ts_settings: Hw timer related settings.
* @shub_settings: i2c controller related settings.
*/
struct st_lsm6dsx_settings {
u8 wai;
- u8 int1_addr;
- u8 int2_addr;
- u8 int1_func_addr;
- u8 int2_func_addr;
- u8 int_func_mask;
u8 reset_addr;
u16 max_fifo_size;
struct {
@@ -269,12 +261,18 @@ struct st_lsm6dsx_settings {
const struct iio_chan_spec *chan;
int len;
} channels[2];
+ struct {
+ struct st_lsm6dsx_reg irq1;
+ struct st_lsm6dsx_reg irq2;
+ struct st_lsm6dsx_reg irq1_func;
+ struct st_lsm6dsx_reg irq2_func;
+ struct st_lsm6dsx_reg lir;
+ struct st_lsm6dsx_reg clear_on_read;
+ } irq_config;
struct st_lsm6dsx_odr_table_entry odr_table[2];
struct st_lsm6dsx_fs_table_entry fs_table[2];
struct st_lsm6dsx_reg decimator[ST_LSM6DSX_MAX_ID];
struct st_lsm6dsx_reg batch[ST_LSM6DSX_MAX_ID];
- struct st_lsm6dsx_reg lir;
- struct st_lsm6dsx_reg clear_on_read;
struct st_lsm6dsx_fifo_ops fifo_ops;
struct st_lsm6dsx_hw_ts_settings ts_settings;
struct st_lsm6dsx_shub_settings shub_settings;
@@ -359,9 +357,9 @@ struct st_lsm6dsx_hw {
u8 ts_sip;
u8 sip;
+ const struct st_lsm6dsx_reg *irq_routing;
u8 event_threshold;
u8 enable_event;
- struct st_lsm6dsx_reg irq_routing;
u8 *buff;
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
index eac695663b6f..23d67caa24ed 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c
@@ -61,7 +61,6 @@
#include "st_lsm6dsx.h"
-#define ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK BIT(3)
#define ST_LSM6DSX_REG_WHOAMI_ADDR 0x0f
#define ST_LSM6DSX_REG_RESET_MASK BIT(0)
#define ST_LSM6DSX_REG_BOOT_MASK BIT(7)
@@ -97,8 +96,6 @@ static const struct iio_chan_spec st_lsm6ds0_gyro_channels[] = {
static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
{
.wai = 0x68,
- .int1_addr = 0x0c,
- .int2_addr = 0x0d,
.reset_addr = 0x22,
.max_fifo_size = 32,
.id = {
@@ -164,14 +161,19 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[2] = { IIO_DEGREE_TO_RAD(2000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0c,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ },
},
{
.wai = 0x69,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 1365,
.id = {
@@ -238,6 +240,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -248,10 +272,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -297,11 +317,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x69,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 682,
.id = {
@@ -368,6 +383,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -378,10 +415,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -427,11 +460,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6a,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 682,
.id = {
@@ -507,6 +535,28 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x58,
+ .mask = BIT(0),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.decimator = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x08,
@@ -517,10 +567,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(5, 3),
},
},
- .lir = {
- .addr = 0x58,
- .mask = BIT(0),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_fifo,
@@ -570,8 +616,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6c,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -641,6 +685,24 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -651,14 +713,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -711,11 +765,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6b,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -782,6 +831,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -792,14 +867,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -841,11 +908,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
},
{
.wai = 0x6b,
- .int1_addr = 0x0d,
- .int2_addr = 0x0e,
- .int1_func_addr = 0x5e,
- .int2_func_addr = 0x5f,
- .int_func_mask = BIT(5),
.reset_addr = 0x12,
.max_fifo_size = 512,
.id = {
@@ -915,6 +977,32 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.fs_avl[3] = { IIO_DEGREE_TO_RAD(70000), 0x3 },
},
},
+ .irq_config = {
+ .irq1 = {
+ .addr = 0x0d,
+ .mask = BIT(3),
+ },
+ .irq2 = {
+ .addr = 0x0e,
+ .mask = BIT(3),
+ },
+ .lir = {
+ .addr = 0x56,
+ .mask = BIT(0),
+ },
+ .clear_on_read = {
+ .addr = 0x56,
+ .mask = BIT(6),
+ },
+ .irq1_func = {
+ .addr = 0x5e,
+ .mask = BIT(5),
+ },
+ .irq2_func = {
+ .addr = 0x5f,
+ .mask = BIT(5),
+ },
+ },
.batch = {
[ST_LSM6DSX_ID_ACC] = {
.addr = 0x09,
@@ -925,14 +1013,6 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = {
.mask = GENMASK(7, 4),
},
},
- .lir = {
- .addr = 0x56,
- .mask = BIT(0),
- },
- .clear_on_read = {
- .addr = 0x56,
- .mask = BIT(6),
- },
.fifo_ops = {
.update_fifo = st_lsm6dsx_update_fifo,
.read_fifo = st_lsm6dsx_read_tagged_fifo,
@@ -1281,7 +1361,7 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
int err;
u8 enable = 0;
- if (!hw->settings->int1_func_addr)
+ if (!hw->settings->irq_config.irq1_func.addr)
return -ENOTSUPP;
enable = state ? hw->settings->event_settings.enable_reg.mask : 0;
@@ -1293,12 +1373,11 @@ static int st_lsm6dsx_event_setup(struct st_lsm6dsx_hw *hw, int state)
if (err < 0)
return err;
- enable = state ? hw->irq_routing.mask : 0;
+ enable = state ? hw->irq_routing->mask : 0;
/* Enable wakeup interrupt */
- return regmap_update_bits(hw->regmap, hw->irq_routing.addr,
- hw->irq_routing.mask,
- enable);
+ return regmap_update_bits(hw->regmap, hw->irq_routing->addr,
+ hw->irq_routing->mask, enable);
}
static int st_lsm6dsx_read_event(struct iio_dev *iio_dev,
@@ -1527,7 +1606,9 @@ static int st_lsm6dsx_of_get_drdy_pin(struct st_lsm6dsx_hw *hw, int *drdy_pin)
return of_property_read_u32(np, "st,drdy-int-pin", drdy_pin);
}
-static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
+static int
+st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw,
+ const struct st_lsm6dsx_reg **drdy_reg)
{
int err = 0, drdy_pin;
@@ -1541,14 +1622,12 @@ static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg)
switch (drdy_pin) {
case 1:
- *drdy_reg = hw->settings->int1_addr;
- hw->irq_routing.addr = hw->settings->int1_func_addr;
- hw->irq_routing.mask = hw->settings->int_func_mask;
+ hw->irq_routing = &hw->settings->irq_config.irq1_func;
+ *drdy_reg = &hw->settings->irq_config.irq1;
break;
case 2:
- *drdy_reg = hw->settings->int2_addr;
- hw->irq_routing.addr = hw->settings->int2_func_addr;
- hw->irq_routing.mask = hw->settings->int_func_mask;
+ hw->irq_routing = &hw->settings->irq_config.irq2_func;
+ *drdy_reg = &hw->settings->irq_config.irq2;
break;
default:
dev_err(hw->dev, "unsupported data ready pin\n");
@@ -1644,7 +1723,7 @@ static int st_lsm6dsx_init_hw_timer(struct st_lsm6dsx_hw *hw)
static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
{
- u8 drdy_int_reg;
+ const struct st_lsm6dsx_reg *reg;
int err;
/* device sw reset */
@@ -1673,35 +1752,29 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw)
return err;
/* enable FIFO watermak interrupt */
- err = st_lsm6dsx_get_drdy_reg(hw, &drdy_int_reg);
+ err = st_lsm6dsx_get_drdy_reg(hw, ®);
if (err < 0)
return err;
- err = regmap_update_bits(hw->regmap, drdy_int_reg,
- ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
- FIELD_PREP(ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK,
- 1));
+ err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
/* enable Latched interrupts for device events */
- if (hw->settings->lir.addr) {
- unsigned int data;
-
- data = ST_LSM6DSX_SHIFT_VAL(1, hw->settings->lir.mask);
- err = regmap_update_bits(hw->regmap, hw->settings->lir.addr,
- hw->settings->lir.mask, data);
+ if (hw->settings->irq_config.lir.addr) {
+ reg = &hw->settings->irq_config.lir;
+ err = regmap_update_bits(hw->regmap, reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
/* enable clear on read for latched interrupts */
- if (hw->settings->clear_on_read.addr) {
- data = ST_LSM6DSX_SHIFT_VAL(1,
- hw->settings->clear_on_read.mask);
+ if (hw->settings->irq_config.clear_on_read.addr) {
+ reg = &hw->settings->irq_config.clear_on_read;
err = regmap_update_bits(hw->regmap,
- hw->settings->clear_on_read.addr,
- hw->settings->clear_on_read.mask,
- data);
+ reg->addr, reg->mask,
+ ST_LSM6DSX_SHIFT_VAL(1, reg->mask));
if (err < 0)
return err;
}
--
2.21.0
next prev parent reply other threads:[~2019-10-06 13:22 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-06 13:21 [PATCH 00/13] various st_lsm6dsx fixes and missing bits Lorenzo Bianconi
2019-10-06 13:21 ` [PATCH 01/13] iio: imu: st_lsm6dsx: use st_lsm6dsx_read_locked in st_lsm6dsx_report_motion_event Lorenzo Bianconi
2019-10-07 7:54 ` Sean Nyekjaer
2019-10-12 12:08 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 02/13] iio: imu: st_lsm6dsx: add sanity check for read_fifo pointer Lorenzo Bianconi
2019-10-06 13:21 ` Lorenzo Bianconi [this message]
2019-10-07 7:54 ` [PATCH 03/13] iio: imu: st_lsm6dsx: move irq related definitions in irq_config Sean Nyekjaer
2019-10-12 12:13 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 04/13] iio: imu: st_lsm6dsx: do not access active-low/open-drain regs if not supported Lorenzo Bianconi
2019-10-12 12:14 ` Jonathan Cameron
2019-10-06 13:21 ` [PATCH 05/13] iio: imu: st_lsm6dsx: move bdu/boot and reset register info in hw_settings Lorenzo Bianconi
2019-10-12 12:19 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 06/13] iio: imu: st_lsm6dsx: always check enable_reg in st_lsm6dsx_event_setup Lorenzo Bianconi
2019-10-07 7:55 ` Sean Nyekjaer
2019-10-12 12:21 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 07/13] iio: imu: st_lsm6dsx: rely on st_lsm6dsx_update_bits_locked configuring events Lorenzo Bianconi
2019-10-12 12:22 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 08/13] iio: imu: st_lsm6dsx: grab conf mutex in st_lsm6dsx_write_event_config Lorenzo Bianconi
2019-10-12 12:23 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 09/13] iio: imu: st_lsm6dsx: fix checkpatch warning Lorenzo Bianconi
2019-10-12 12:24 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 10/13] iio: imu: st_lsm6dsx: add wakeup_source in st_sensors_platform_data Lorenzo Bianconi
2019-10-12 12:25 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 11/13] iio: imu: st_lsm6dsx: add missing kernel documenation Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-12 12:26 ` Jonathan Cameron
2019-10-06 13:22 ` [PATCH 12/13] dt-bindings: iio: imu: st_lsm6dsx: document missing wakeup-source property Lorenzo Bianconi
2019-10-07 7:56 ` Sean Nyekjaer
2019-10-15 20:34 ` Rob Herring
2019-10-06 13:22 ` [PATCH 13/13] iio: imu: st_lsm6dsx: enable wake-up event for LSM6DSO Lorenzo Bianconi
2019-10-12 12:28 ` Jonathan Cameron
2019-10-12 12:20 ` [PATCH 00/13] various st_lsm6dsx fixes and missing bits Jonathan Cameron
2019-10-12 12:26 ` Lorenzo Bianconi
2019-10-12 13:26 ` Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=873559493f99be2a659f27da293f66a546598c2b.1570367532.git.lorenzo@kernel.org \
--to=lorenzo@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=jic23@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=lorenzo.bianconi@redhat.com \
--cc=martin@geanix.com \
--cc=rjones@gateworks.com \
--cc=sean@geanix.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).