linux-leds.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: "Guido Günther" <agx@sigxcpu.org>
To: Jacek Anaszewski <jacek.anaszewski@gmail.com>,
	Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v3 9/9] leds: lm3692x: Disable chip on brightness 0
Date: Sat,  4 Jan 2020 11:54:25 +0100	[thread overview]
Message-ID: <e5b79abde26acd6d1b9f04a313a3f25e1cee995d.1578134779.git.agx@sigxcpu.org> (raw)
In-Reply-To: <cover.1578134779.git.agx@sigxcpu.org>

Otherwise there's a noticeable glow even with brightness 0. Also
turning off the regulator can save additional power.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 drivers/leds/leds-lm3692x.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/leds/leds-lm3692x.c b/drivers/leds/leds-lm3692x.c
index 075dc4b6b3b6..933b786cfaec 100644
--- a/drivers/leds/leds-lm3692x.c
+++ b/drivers/leds/leds-lm3692x.c
@@ -117,6 +117,7 @@ struct lm3692x_led {
 	int model_id;
 
 	u8 boost_ctrl, brightness_ctrl;
+	bool enabled;
 };
 
 static const struct reg_default lm3692x_reg_defs[] = {
@@ -170,6 +171,9 @@ static int lm3692x_leds_enable(struct lm3692x_led *led)
 	int enable_state;
 	int ret, reg_ret;
 
+	if (led->enabled)
+		return 0;
+
 	if (led->regulator) {
 		ret = regulator_enable(led->regulator);
 		if (ret) {
@@ -271,6 +275,7 @@ static int lm3692x_leds_enable(struct lm3692x_led *led)
 	ret = regmap_update_bits(led->regmap, LM3692X_EN, LM3692X_ENABLE_MASK,
 				 enable_state | LM3692X_DEVICE_EN);
 
+	led->enabled = true;
 	return ret;
 out:
 	dev_err(&led->client->dev, "Fail writing initialization values\n");
@@ -292,6 +297,9 @@ static int lm3692x_leds_disable(struct lm3692x_led *led)
 {
 	int ret;
 
+	if (!led->enabled)
+		return 0;
+
 	ret = regmap_update_bits(led->regmap, LM3692X_EN, LM3692X_DEVICE_EN, 0);
 	if (ret) {
 		dev_err(&led->client->dev, "Failed to disable regulator: %d\n",
@@ -309,6 +317,7 @@ static int lm3692x_leds_disable(struct lm3692x_led *led)
 				"Failed to disable regulator: %d\n", ret);
 	}
 
+	led->enabled = false;
 	return ret;
 }
 
@@ -322,6 +331,13 @@ static int lm3692x_brightness_set(struct led_classdev *led_cdev,
 
 	mutex_lock(&led->lock);
 
+	if (brt_val == 0) {
+		ret = lm3692x_leds_disable(led);
+		goto out;
+	} else {
+		lm3692x_leds_enable(led);
+	}
+
 	ret = lm3692x_fault_check(led);
 	if (ret) {
 		dev_err(&led->client->dev, "Cannot read/clear faults: %d\n",
-- 
2.23.0


  parent reply	other threads:[~2020-01-04 10:54 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-04 10:54 [PATCH v3 0/9] leds: lm3692x: Allow to set ovp and brigthness mode Guido Günther
2020-01-04 10:54 ` [PATCH v3 1/9] dt: bindings: lm3692x: Add ti,ovp-microvolt property Guido Günther
2020-01-04 21:11   ` Rob Herring
2020-01-04 10:54 ` [PATCH v3 2/9] leds: lm3692x: Allow to configure over voltage protection Guido Günther
2020-01-04 10:54 ` [PATCH v3 3/9] dt: bindings: lm3692x: Add ti,brightness-mapping-exponential property Guido Günther
2020-01-04 21:11   ` Rob Herring
2020-01-04 10:54 ` [PATCH v3 4/9] leds: lm3692x: Allow to configure brigthness mode Guido Günther
2020-01-04 10:54 ` [PATCH v3 5/9] dt: bindings: lm3692x: Add led-max-microamp property Guido Günther
2020-01-04 21:11   ` Rob Herring
2020-01-04 10:54 ` [PATCH v3 6/9] leds: lm3692x: Make sure we don't exceed the maximum led current Guido Günther
2020-01-04 10:54 ` [PATCH v3 7/9] leds: lm3692x: Move lm3692x_init and rename to lm3692x_leds_enable Guido Günther
2020-01-04 10:54 ` [PATCH v3 8/9] leds: lm3692x: Split out lm3692x_leds_disable Guido Günther
2020-01-04 10:54 ` Guido Günther [this message]
2020-01-05 23:47 ` [PATCH v3 0/9] leds: lm3692x: Allow to set ovp and brigthness mode Pavel Machek
2020-01-06  9:44   ` Guido Günther
2020-02-25 10:19     ` Pavel Machek

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=e5b79abde26acd6d1b9f04a313a3f25e1cee995d.1578134779.git.agx@sigxcpu.org \
    --to=agx@sigxcpu.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=jacek.anaszewski@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=pavel@ucw.cz \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).