On Tue, May 28, 2019 at 11:07:29AM +0200, Lubomir Rintel wrote:
> The platform data is actually not used anywhere (along with the CSI
> support) and should be safe to remove.
>
> Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
> Acked-by: Pavel Machek <pavel@ucw.cz>
>
> ---
> Changes since v1:
> - s/This are/These are/ in a comment
>
>  .../media/platform/marvell-ccic/mmp-driver.c  | 36 ++++++++++++++-----
>  1 file changed, 27 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/media/platform/marvell-ccic/mmp-driver.c b/drivers/media/platform/marvell-ccic/mmp-driver.c
> index 8f1d2a972bc9..54c2dd8c29d8 100644
> --- a/drivers/media/platform/marvell-ccic/mmp-driver.c
> +++ b/drivers/media/platform/marvell-ccic/mmp-driver.c
> @@ -19,6 +19,8 @@
>  #include <media/v4l2-device.h>
>  #include <linux/platform_data/media/mmp-camera.h>
>  #include <linux/device.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
>  #include <linux/platform_device.h>
>  #include <linux/gpio.h>
>  #include <linux/io.h>
> @@ -196,6 +198,9 @@ static void mmpcam_calc_dphy(struct mcam_camera *mcam)
>  	struct device *dev = &cam->pdev->dev;
>  	unsigned long tx_clk_esc;
>
> +	if (!pdata)
> +		return;
> +

This seems a bit of an hack to me. The caller knows the mcam->bus_type
and should not try to calc_dphy() if the bus type is not CSI2_DPHY.
What do you think?

>  	/*
>  	 * If CSI2_DPHY3 is calculated dynamically,
>  	 * pdata->lane_clk should be already set
> @@ -314,10 +319,6 @@ static int mmpcam_probe(struct platform_device *pdev)
>  	struct mmp_camera_platform_data *pdata;
>  	int ret;
>
> -	pdata = pdev->dev.platform_data;
> -	if (!pdata)
> -		return -ENODEV;
> -
>  	cam = devm_kzalloc(&pdev->dev, sizeof(*cam), GFP_KERNEL);
>  	if (cam == NULL)
>  		return -ENOMEM;
> @@ -330,17 +331,29 @@ static int mmpcam_probe(struct platform_device *pdev)
>  	mcam->calc_dphy = mmpcam_calc_dphy;
>  	mcam->dev = &pdev->dev;
>  	mcam->use_smbus = 0;
> -	mcam->mclk_src = pdata->mclk_src;
> -	mcam->mclk_div = pdata->mclk_div;
> -	mcam->bus_type = pdata->bus_type;
> -	mcam->dphy = pdata->dphy;
> +	pdata = pdev->dev.platform_data;
> +	if (pdata) {
> +		mcam->mclk_src = pdata->mclk_src;
> +		mcam->mclk_div = pdata->mclk_div;
> +		mcam->bus_type = pdata->bus_type;
> +		mcam->dphy = pdata->dphy;
> +		mcam->lane = pdata->lane;
> +	} else {
> +		/*
> +		 * These are values that used to be hardcoded in mcam-core and
> +		 * work well on a OLPC XO 1.75 with a parallel bus sensor.
> +		 * If it turns out other setups make sense, the values should
> +		 * be obtained from the device tree.
> +		 */
> +		mcam->mclk_src = 3;
> +		mcam->mclk_div = 2;

I see these only used in mcam_enable_mipi(). Am I wrong?

Thanks
   j

> +	}
>  	if (mcam->bus_type == V4L2_MBUS_CSI2_DPHY) {
>  		cam->mipi_clk = devm_clk_get(mcam->dev, "mipi");
>  		if ((IS_ERR(cam->mipi_clk) && mcam->dphy[2] == 0))
>  			return PTR_ERR(cam->mipi_clk);
>  	}
>  	mcam->mipi_enabled = false;
> -	mcam->lane = pdata->lane;
>  	mcam->chip_id = MCAM_ARMADA610;
>  	mcam->buffer_mode = B_DMA_sg;
>  	strscpy(mcam->bus_info, "platform:mmp-camera", sizeof(mcam->bus_info));
> @@ -475,6 +488,10 @@ static int mmpcam_resume(struct platform_device *pdev)
>
>  #endif
>
> +static const struct of_device_id mmpcam_of_match[] = {
> +	{ .compatible = "marvell,mmp2-ccic", },
> +	{},
> +};
>
>  static struct platform_driver mmpcam_driver = {
>  	.probe		= mmpcam_probe,
> @@ -485,6 +502,7 @@ static struct platform_driver mmpcam_driver = {
>  #endif
>  	.driver = {
>  		.name	= "mmp-camera",
> +		.of_match_table = of_match_ptr(mmpcam_of_match),
>  	}
>  };
>
> --
> 2.21.0
>