From: Remi Pommarel <repk@triplefau.lt>
To: Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>,
Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Miquel Raynal <miquel.raynal@bootlin.com>,
Remi Pommarel <repk@triplefau.lt>
Subject: [PATCH] pci: aardvark: Wait for endpoint to be ready before training link
Date: Wed, 13 Mar 2019 22:37:52 +0100 [thread overview]
Message-ID: <20190313213752.1246-1-repk@triplefau.lt> (raw)
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
This makes sure that link is configured after at least 100ms from
beginning of probe() callback (shortly after the reset pin function
configuration switch through pinctrl subsytem).
[1] "PCI Express Base Specification", REV. 2.1
PCI Express, March 4 2009, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
---
drivers/pci/controller/pci-aardvark.c | 17 ++++++++++++++---
1 file changed, 14 insertions(+), 3 deletions(-)
diff --git a/drivers/pci/controller/pci-aardvark.c b/drivers/pci/controller/pci-aardvark.c
index a30ae7cf8e7e..70a1023d0ef1 100644
--- a/drivers/pci/controller/pci-aardvark.c
+++ b/drivers/pci/controller/pci-aardvark.c
@@ -177,6 +177,9 @@
#define PIO_TIMEOUT_MS 1
+/* Endpoint can take up to 100ms to be ready after a reset */
+#define ENDPOINT_RST_MS 100
+
#define LINK_WAIT_MAX_RETRIES 10
#define LINK_WAIT_USLEEP_MIN 90000
#define LINK_WAIT_USLEEP_MAX 100000
@@ -242,8 +245,10 @@ static int advk_pcie_wait_for_link(struct advk_pcie *pcie)
return -ETIMEDOUT;
}
-static void advk_pcie_setup_hw(struct advk_pcie *pcie)
+static void
+advk_pcie_setup_hw(struct advk_pcie *pcie, unsigned long ep_rdy_time)
{
+ unsigned long now;
u32 reg;
/* Set to Direct mode */
@@ -327,9 +332,12 @@ static void advk_pcie_setup_hw(struct advk_pcie *pcie)
reg |= PIO_CTRL_ADDR_WIN_DISABLE;
advk_writel(pcie, reg, PIO_CTRL);
- /* Start link training */
+ /* Wait for endpoint to exit reset state and start link training */
reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
reg |= PCIE_CORE_LINK_TRAINING;
+ now = jiffies;
+ if (time_before(now, ep_rdy_time))
+ msleep(jiffies_to_msecs(ep_rdy_time - now));
advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
advk_pcie_wait_for_link(pcie);
@@ -993,8 +1001,11 @@ static int advk_pcie_probe(struct platform_device *pdev)
struct advk_pcie *pcie;
struct resource *res;
struct pci_host_bridge *bridge;
+ unsigned long ep_rdy_time;
int ret, irq;
+ ep_rdy_time = jiffies + msecs_to_jiffies(ENDPOINT_RST_MS);
+
bridge = devm_pci_alloc_host_bridge(dev, sizeof(struct advk_pcie));
if (!bridge)
return -ENOMEM;
@@ -1022,7 +1033,7 @@ static int advk_pcie_probe(struct platform_device *pdev)
return ret;
}
- advk_pcie_setup_hw(pcie);
+ advk_pcie_setup_hw(pcie, ep_rdy_time);
advk_sw_pci_bridge_init(pcie);
--
2.20.1
next reply other threads:[~2019-03-13 21:29 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-13 21:37 Remi Pommarel [this message]
2019-04-23 16:32 ` [PATCH] pci: aardvark: Wait for endpoint to be ready before training link Lorenzo Pieralisi
2019-04-23 22:29 ` Remi Pommarel
2019-04-24 16:50 ` Lorenzo Pieralisi
2019-04-25 21:08 ` Remi Pommarel
2019-04-26 16:10 ` Bjorn Helgaas
2019-04-26 17:16 ` Lorenzo Pieralisi
2019-04-25 16:30 ` Bjorn Helgaas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190313213752.1246-1-repk@triplefau.lt \
--to=repk@triplefau.lt \
--cc=bhelgaas@google.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=miquel.raynal@bootlin.com \
--cc=thomas.petazzoni@bootlin.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).