Re: [PATCH v2] PCI: dwc: Add support to add GEN3 related equalization quirks

[Andrew Murray <andrew.murray@arm.com>]

On Mon, Sep 16, 2019 at 04:36:33PM +0530, Pankaj Dubey wrote:
> 
> 
> > -----Original Message-----
> > From: Andrew Murray <andrew.murray@arm.com>
> > Sent: Monday, September 16, 2019 3:46 PM
> > To: Pankaj Dubey <pankaj.dubey@samsung.com>
> > Cc: linux-pci@vger.kernel.org; linux-kernel@vger.kernel.org;
> > jingoohan1@gmail.com; gustavo.pimentel@synopsys.com;
> > lorenzo.pieralisi@arm.com; bhelgaas@google.com; Anvesh Salveru
> > <anvesh.s@samsung.com>
> > Subject: Re: [PATCH v2] PCI: dwc: Add support to add GEN3 related
> equalization
> > quirks
> > 
> > On Fri, Sep 13, 2019 at 04:09:50PM +0530, Pankaj Dubey wrote:
> > > From: Anvesh Salveru <anvesh.s@samsung.com>
> > >
> > > In some platforms, PCIe PHY may have issues which will prevent linkup
> > > to happen in GEN3 or higher speed. In case equalization fails, link
> > > will fallback to GEN1.
> > >
> > > DesignWare controller gives flexibility to disable GEN3 equalization
> > > completely or only phase 2 and 3 of equalization.
> > >
> > > This patch enables the DesignWare driver to disable the PCIe GEN3
> > > equalization by enabling one of the following quirks:
> > >  - DWC_EQUALIZATION_DISABLE: To disable GEN3 equalization all phases
> > >  - DWC_EQ_PHASE_2_3_DISABLE: To disable GEN3 equalization phase 2 & 3
> > >
> > > Platform drivers can set these quirks via "quirk" variable of "dw_pcie"
> > > struct.
> > >
> > > Signed-off-by: Anvesh Salveru <anvesh.s@samsung.com>
> > > Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
> > > ---
> > > Patchset v1 can be found at:
> > >  - 1/2: https://lkml.org/lkml/2019/9/10/443
> > >  - 2/2: https://lkml.org/lkml/2019/9/10/444
> > >
> > > Changes w.r.t v1:
> > >  - Squashed two patches from v1 into one as suggested by Gustavo
> > >  - Addressed review comments from Andrew
> > >
> > >  drivers/pci/controller/dwc/pcie-designware.c | 12 ++++++++++++
> > > drivers/pci/controller/dwc/pcie-designware.h |  9 +++++++++
> > >  2 files changed, 21 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c
> > > b/drivers/pci/controller/dwc/pcie-designware.c
> > > index 7d25102..97fb18d 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.c
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.c
> > > @@ -466,4 +466,16 @@ void dw_pcie_setup(struct dw_pcie *pci)
> > >  		break;
> > >  	}
> > >  	dw_pcie_writel_dbi(pci, PCIE_LINK_WIDTH_SPEED_CONTROL, val);
> > > +
> > > +	if (pci->quirk & DWC_EQUALIZATION_DISABLE) {
> > > +		val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
> > > +		val |= PORT_LOGIC_GEN3_EQ_DISABLE;
> > > +		dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
> > > +	}
> > > +
> > > +	if (pci->quirk & DWC_EQ_PHASE_2_3_DISABLE) {
> > > +		val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
> > > +		val |= PORT_LOGIC_GEN3_EQ_PHASE_2_3_DISABLE;
> > > +		dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
> > > +	}
> > >  }
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h
> > > b/drivers/pci/controller/dwc/pcie-designware.h
> > > index ffed084..e428b62 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.h
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.h
> > > @@ -29,6 +29,10 @@
> > >  #define LINK_WAIT_MAX_IATU_RETRIES	5
> > >  #define LINK_WAIT_IATU			9
> > >
> > > +/* Parameters for GEN3 related quirks */
> > > +#define DWC_EQUALIZATION_DISABLE	BIT(1)
> > > +#define DWC_EQ_PHASE_2_3_DISABLE	BIT(2)
> > > +
> > >  /* Synopsys-specific PCIe configuration registers */
> > >  #define PCIE_PORT_LINK_CONTROL		0x710
> > >  #define PORT_LINK_MODE_MASK		GENMASK(21, 16)
> > > @@ -60,6 +64,10 @@
> > >  #define PCIE_MSI_INTR0_MASK		0x82C
> > >  #define PCIE_MSI_INTR0_STATUS		0x830
> > >
> > > +#define PCIE_PORT_GEN3_RELATED		0x890
> > 
> > I hadn't noticed this in the previous version - what is the proper name
> for this
> > register? Does it end in _RELATED?
> 
> As per SNPS databook the name of the register is "GEN3_RELATED_OFF". It is
> port logic register so, to keep similarity with other port logic registers
> in this file we named it as "PCIE_PORT_GEN3_RELATED". 

OK.

Reviewed-by: Andrew Murray <andrew.murray@arm.com>

Also is the SNPS databook publicly available? I'd be interested in reading
it.

Thanks,

Andrew Murray

> 
> > 
> > Thanks,
> > 
> > Andrew Murray
> > 
> > > +#define PORT_LOGIC_GEN3_EQ_PHASE_2_3_DISABLE	BIT(9)
> > > +#define PORT_LOGIC_GEN3_EQ_DISABLE		BIT(16)
> > > +
> > >  #define PCIE_ATU_VIEWPORT		0x900
> > >  #define PCIE_ATU_REGION_INBOUND		BIT(31)
> > >  #define PCIE_ATU_REGION_OUTBOUND	0
> > > @@ -244,6 +252,7 @@ struct dw_pcie {
> > >  	struct dw_pcie_ep	ep;
> > >  	const struct dw_pcie_ops *ops;
> > >  	unsigned int		version;
> > > +	unsigned int		quirk;
> > >  };
> > >
> > >  #define to_dw_pcie_from_pp(port) container_of((port), struct dw_pcie,
> > > pp)
> > > --
> > > 2.7.4
> > >
>