From: Georgi Djakov <georgi.djakov@linaro.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: robh+dt@kernel.org, agross@kernel.org, vkoul@kernel.org,
evgreen@chromium.org, daidavid1@codeaurora.org,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org
Subject: Re: [PATCH v4 1/5] dt-bindings: interconnect: Add Qualcomm QCS404 DT bindings
Date: Mon, 15 Jul 2019 16:56:03 +0300 [thread overview]
Message-ID: <70982f11-792e-6c02-056d-47582708be4f@linaro.org> (raw)
In-Reply-To: <20190708192612.GE30636@minitux>
Hi Bjorn,
On 7/8/19 22:26, Bjorn Andersson wrote:
> On Thu 13 Jun 08:13 PDT 2019, Georgi Djakov wrote:
>
>> The Qualcomm QCS404 platform has several buses that could be controlled
>> and tuned according to the bandwidth demand.
>>
>> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
>> Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
>> ---
>>
>> v4:
>> - Add the DT header into this patch.
>> - Pick Bjorn's r-b.
>>
>> v3:
>> - Add a reg property and move the interconnect nodes under the "soc" node.
>>
>> v2:
>> - No changes.
>>
>> .../bindings/interconnect/qcom,qcs404.txt | 46 ++++++++++
>> .../dt-bindings/interconnect/qcom,qcs404.h | 88 +++++++++++++++++++
>> 2 files changed, 134 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt
>> create mode 100644 include/dt-bindings/interconnect/qcom,qcs404.h
>>
>> diff --git a/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt b/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt
>> new file mode 100644
>> index 000000000000..14a827268dda
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/interconnect/qcom,qcs404.txt
>> @@ -0,0 +1,46 @@
>> +Qualcomm QCS404 Network-On-Chip interconnect driver binding
>> +-----------------------------------------------------------
>> +
>> +Required properties :
>> +- compatible : shall contain only one of the following:
>> + "qcom,qcs404-bimc"
>> + "qcom,qcs404-pcnoc"
>> + "qcom,qcs404-snoc"
>> +- #interconnect-cells : should contain 1
>> +
>> +Optional properties :
>> +reg : specifies the physical base address and size of registers
>> +clocks : list of phandles and specifiers to all interconnect bus clocks
>> +clock-names : clock names should include both "bus_clk" and "bus_a_clk"
>
> Spoke to Rob about this patch, and I don't think these properties should
> not be described as optional.
>
> The reg isn't used unless we're implementing support for QoS, but let's
> include them in the binding as required anyways.
Ok, will do it!
>
> Iirc the two clocks are required with the current implementation, but
> shouldn't there be an iface clock as well, for accessing the QoS
> register space?
Actually i expect this to be a list of AXI clocks of the IP blocks, whose QoS
ports we configure. For this platform, according to downstream, it would be just
<&gcc GCC_SYS_NOC_USB3_CLK>. For other platforms i see these are a few usb/ufs
clocks that should be enabled while we set QoS for usb/ufs.
>
> PS. As I read this again, please drop _clk from the two clocks names -
> we know they are clocks...
Sure, will do it!
Thanks,
Georgi
>
> Regards,
> Bjorn
>
>> +
>> +Example:
>> +
>> +soc {
>> + ...
>> + bimc: interconnect@400000 {
>> + reg = <0x00400000 0x80000>;
>> + compatible = "qcom,qcs404-bimc";
>> + #interconnect-cells = <1>;
>> + clock-names = "bus_clk", "bus_a_clk";
>> + clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
>> + <&rpmcc RPM_SMD_BIMC_A_CLK>;
>> + };
>> +
>> + pnoc: interconnect@500000 {
>> + reg = <0x00500000 0x15080>;
>> + compatible = "qcom,qcs404-pcnoc";
>> + #interconnect-cells = <1>;
>> + clock-names = "bus_clk", "bus_a_clk";
>> + clocks = <&rpmcc RPM_SMD_PNOC_CLK>,
>> + <&rpmcc RPM_SMD_PNOC_A_CLK>;
>> + };
>> +
>> + snoc: interconnect@580000 {
>> + reg = <0x00580000 0x23080>;
>> + compatible = "qcom,qcs404-snoc";
>> + #interconnect-cells = <1>;
>> + clock-names = "bus_clk", "bus_a_clk";
>> + clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
>> + <&rpmcc RPM_SMD_SNOC_A_CLK>;
>> + };
>> +};
>> diff --git a/include/dt-bindings/interconnect/qcom,qcs404.h b/include/dt-bindings/interconnect/qcom,qcs404.h
>> new file mode 100644
>> index 000000000000..960f6e39c5f2
>> --- /dev/null
>> +++ b/include/dt-bindings/interconnect/qcom,qcs404.h
>> @@ -0,0 +1,88 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Qualcomm interconnect IDs
>> + *
>> + * Copyright (c) 2019, Linaro Ltd.
>> + * Author: Georgi Djakov <georgi.djakov@linaro.org>
>> + */
>> +
>> +#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_QCS404_H
>> +#define __DT_BINDINGS_INTERCONNECT_QCOM_QCS404_H
>> +
>> +#define MASTER_AMPSS_M0 0
>> +#define MASTER_OXILI 1
>> +#define MASTER_MDP_PORT0 2
>> +#define MASTER_SNOC_BIMC_1 3
>> +#define MASTER_TCU_0 4
>> +#define SLAVE_EBI_CH0 5
>> +#define SLAVE_BIMC_SNOC 6
>> +
>> +#define MASTER_SPDM 0
>> +#define MASTER_BLSP_1 1
>> +#define MASTER_BLSP_2 2
>> +#define MASTER_XI_USB_HS1 3
>> +#define MASTER_CRYPT0 4
>> +#define MASTER_SDCC_1 5
>> +#define MASTER_SDCC_2 6
>> +#define MASTER_SNOC_PCNOC 7
>> +#define MASTER_QPIC 8
>> +#define PCNOC_INT_0 9
>> +#define PCNOC_INT_2 10
>> +#define PCNOC_INT_3 11
>> +#define PCNOC_S_0 12
>> +#define PCNOC_S_1 13
>> +#define PCNOC_S_2 14
>> +#define PCNOC_S_3 15
>> +#define PCNOC_S_4 16
>> +#define PCNOC_S_6 17
>> +#define PCNOC_S_7 18
>> +#define PCNOC_S_8 19
>> +#define PCNOC_S_9 20
>> +#define PCNOC_S_10 21
>> +#define PCNOC_S_11 22
>> +#define SLAVE_SPDM 23
>> +#define SLAVE_PDM 24
>> +#define SLAVE_PRNG 25
>> +#define SLAVE_TCSR 26
>> +#define SLAVE_SNOC_CFG 27
>> +#define SLAVE_MESSAGE_RAM 28
>> +#define SLAVE_DISP_SS_CFG 29
>> +#define SLAVE_GPU_CFG 30
>> +#define SLAVE_BLSP_1 31
>> +#define SLAVE_BLSP_2 32
>> +#define SLAVE_TLMM_NORTH 33
>> +#define SLAVE_PCIE 34
>> +#define SLAVE_ETHERNET 35
>> +#define SLAVE_TLMM_EAST 36
>> +#define SLAVE_TCU 37
>> +#define SLAVE_PMIC_ARB 38
>> +#define SLAVE_SDCC_1 39
>> +#define SLAVE_SDCC_2 40
>> +#define SLAVE_TLMM_SOUTH 41
>> +#define SLAVE_USB_HS 42
>> +#define SLAVE_USB3 43
>> +#define SLAVE_CRYPTO_0_CFG 44
>> +#define SLAVE_PCNOC_SNOC 45
>> +
>> +#define MASTER_QDSS_BAM 0
>> +#define MASTER_BIMC_SNOC 1
>> +#define MASTER_PCNOC_SNOC 2
>> +#define MASTER_QDSS_ETR 3
>> +#define MASTER_EMAC 4
>> +#define MASTER_PCIE 5
>> +#define MASTER_USB3 6
>> +#define QDSS_INT 7
>> +#define SNOC_INT_0 8
>> +#define SNOC_INT_1 9
>> +#define SNOC_INT_2 10
>> +#define SLAVE_KPSS_AHB 11
>> +#define SLAVE_WCSS 12
>> +#define SLAVE_SNOC_BIMC_1 13
>> +#define SLAVE_IMEM 14
>> +#define SLAVE_SNOC_PCNOC 15
>> +#define SLAVE_QDSS_STM 16
>> +#define SLAVE_CATS_0 17
>> +#define SLAVE_CATS_1 18
>> +#define SLAVE_LPASS 19
>> +
>> +#endif
next prev parent reply other threads:[~2019-07-15 15:09 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-13 15:13 [PATCH v4 0/5] Add QCS404 interconnect provider driver Georgi Djakov
2019-06-13 15:13 ` [PATCH v4 1/5] dt-bindings: interconnect: Add Qualcomm QCS404 DT bindings Georgi Djakov
2019-06-25 15:00 ` Georgi Djakov
2019-07-08 19:26 ` Bjorn Andersson
2019-07-15 13:56 ` Georgi Djakov [this message]
2019-06-13 15:13 ` [PATCH v4 2/5] soc: qcom: smd-rpm: Create RPM interconnect proxy child device Georgi Djakov
2019-06-13 15:40 ` Bjorn Andersson
2019-10-07 2:01 ` Brian Masney
2019-10-07 5:28 ` Bjorn Andersson
2019-06-13 15:13 ` [PATCH v4 3/5] interconnect: qcom: Add interconnect SMD over SMD driver Georgi Djakov
2019-06-13 15:42 ` Bjorn Andersson
2019-06-13 15:13 ` [PATCH v4 4/5] interconnect: qcom: Add QCS404 interconnect provider driver Georgi Djakov
2019-06-13 15:47 ` Bjorn Andersson
2019-06-13 15:13 ` [PATCH v4 5/5] arm64: dts: qcs404: Add interconnect provider DT nodes Georgi Djakov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=70982f11-792e-6c02-056d-47582708be4f@linaro.org \
--to=georgi.djakov@linaro.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=daidavid1@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=evgreen@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).