From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
To: "Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
linux-media@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v3 5/6] rcar-vin: Add support for V4L2_FIELD_ALTERNATE
Date: Fri, 13 Sep 2019 14:34:59 +0100 [thread overview]
Message-ID: <61fd1036-2d11-4761-6cab-93b70a44baf6@ideasonboard.com> (raw)
In-Reply-To: <20190904215409.30136-6-niklas.soderlund+renesas@ragnatech.se>
On 04/09/2019 22:54, Niklas Söderlund wrote:
> The hardware is capable to passing V4L2_FIELD_ALTERNATE to user-space.
s/to/of/
> Allow users to request this field format but still default to using the
> hardware interlacer if alternating is not explicitly requested.
>
> Before this change a sensor providing data using alternate would be
> always combined to an interlaced frame. After this change the user can
s/would be always/would always be/
> request to receive frames as alternate if the sensor provides it.
>
> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
> ---
> drivers/media/platform/rcar-vin/rcar-dma.c | 43 +++++++++++++--------
> drivers/media/platform/rcar-vin/rcar-v4l2.c | 31 +++++++--------
> 2 files changed, 39 insertions(+), 35 deletions(-)
>
> diff --git a/drivers/media/platform/rcar-vin/rcar-dma.c b/drivers/media/platform/rcar-vin/rcar-dma.c
> index 7d40d71c863265c9..c7859b329dd4f02a 100644
> --- a/drivers/media/platform/rcar-vin/rcar-dma.c
> +++ b/drivers/media/platform/rcar-vin/rcar-dma.c
> @@ -529,12 +529,17 @@ static void rvin_set_coeff(struct rvin_dev *vin, unsigned short xs)
>
> static void rvin_crop_scale_comp_gen2(struct rvin_dev *vin)
> {
> + unsigned int crop_height;
> u32 xs, ys;
>
> /* Set scaling coefficient */
> + crop_height = vin->crop.height;
> + if (V4L2_FIELD_IS_INTERLACED(vin->format.field))
> + crop_height *= 2;
> +
> ys = 0;
> - if (vin->crop.height != vin->compose.height)
> - ys = (4096 * vin->crop.height) / vin->compose.height;
> + if (crop_height != vin->compose.height)
> + ys = (4096 * crop_height) / vin->compose.height;
> rvin_write(vin, ys, VNYS_REG);
>
> xs = 0;
> @@ -578,21 +583,9 @@ void rvin_crop_scale_comp(struct rvin_dev *vin)
> /* Set Start/End Pixel/Line Pre-Clip */
> rvin_write(vin, vin->crop.left, VNSPPRC_REG);
> rvin_write(vin, vin->crop.left + vin->crop.width - 1, VNEPPRC_REG);
> + rvin_write(vin, vin->crop.top, VNSLPRC_REG);
> + rvin_write(vin, vin->crop.top + vin->crop.height - 1, VNELPRC_REG);
>
> - switch (vin->format.field) {
> - case V4L2_FIELD_INTERLACED:
> - case V4L2_FIELD_INTERLACED_TB:
> - case V4L2_FIELD_INTERLACED_BT:
> - rvin_write(vin, vin->crop.top / 2, VNSLPRC_REG);
> - rvin_write(vin, (vin->crop.top + vin->crop.height) / 2 - 1,
> - VNELPRC_REG);
> - break;
> - default:
> - rvin_write(vin, vin->crop.top, VNSLPRC_REG);
> - rvin_write(vin, vin->crop.top + vin->crop.height - 1,
> - VNELPRC_REG);
> - break;
> - }
>
> /* TODO: Add support for the UDS scaler. */
> if (vin->info->model != RCAR_GEN3)
> @@ -636,6 +629,9 @@ static int rvin_setup(struct rvin_dev *vin)
> vnmc = VNMC_IM_ODD_EVEN;
> progressive = true;
> break;
> + case V4L2_FIELD_ALTERNATE:
> + vnmc = VNMC_IM_ODD_EVEN;
> + break;
> default:
> vnmc = VNMC_IM_ODD;
> break;
> @@ -794,6 +790,18 @@ static bool rvin_capture_active(struct rvin_dev *vin)
> return rvin_read(vin, VNMS_REG) & VNMS_CA;
> }
>
> +static enum v4l2_field rvin_get_active_field(struct rvin_dev *vin, u32 vnms)
> +{
> + if (vin->format.field == V4L2_FIELD_ALTERNATE) {
> + /* If FS is set it is an Even field. */
> + if (vnms & VNMS_FS)
> + return V4L2_FIELD_BOTTOM;
> + return V4L2_FIELD_TOP;
> + }
> +
> + return vin->format.field;
> +}
> +
> static void rvin_set_slot_addr(struct rvin_dev *vin, int slot, dma_addr_t addr)
> {
> const struct rvin_video_format *fmt;
> @@ -943,7 +951,7 @@ static irqreturn_t rvin_irq(int irq, void *data)
>
> /* Capture frame */
> if (vin->queue_buf[slot]) {
> - vin->queue_buf[slot]->field = vin->format.field;
> + vin->queue_buf[slot]->field = rvin_get_active_field(vin, vnms);
> vin->queue_buf[slot]->sequence = vin->sequence;
> vin->queue_buf[slot]->vb2_buf.timestamp = ktime_get_ns();
> vb2_buffer_done(&vin->queue_buf[slot]->vb2_buf,
> @@ -1070,6 +1078,7 @@ static int rvin_mc_validate_format(struct rvin_dev *vin, struct v4l2_subdev *sd,
> case V4L2_FIELD_TOP:
> case V4L2_FIELD_BOTTOM:
> case V4L2_FIELD_NONE:
> + case V4L2_FIELD_ALTERNATE:
> break;
> case V4L2_FIELD_INTERLACED_TB:
> case V4L2_FIELD_INTERLACED_BT:
> diff --git a/drivers/media/platform/rcar-vin/rcar-v4l2.c b/drivers/media/platform/rcar-vin/rcar-v4l2.c
> index 3f175e2e0a9a1389..a7ee44dd248ea0a1 100644
> --- a/drivers/media/platform/rcar-vin/rcar-v4l2.c
> +++ b/drivers/media/platform/rcar-vin/rcar-v4l2.c
> @@ -117,15 +117,7 @@ static void rvin_format_align(struct rvin_dev *vin, struct v4l2_pix_format *pix)
> case V4L2_FIELD_INTERLACED_TB:
> case V4L2_FIELD_INTERLACED_BT:
> case V4L2_FIELD_INTERLACED:
> - break;
> case V4L2_FIELD_ALTERNATE:
> - /*
> - * Driver does not (yet) support outputting ALTERNATE to a
> - * userspace. It does support outputting INTERLACED so use
> - * the VIN hardware to combine the two fields.
> - */
> - pix->field = V4L2_FIELD_INTERLACED;
> - pix->height *= 2;
> break;
> default:
> pix->field = RVIN_DEFAULT_FIELD;
> @@ -164,15 +156,25 @@ static int rvin_reset_format(struct rvin_dev *vin)
>
> v4l2_fill_pix_format(&vin->format, &fmt.format);
>
> - rvin_format_align(vin, &vin->format);
> -
> vin->src_rect.top = 0;
> vin->src_rect.left = 0;
> vin->src_rect.width = vin->format.width;
> vin->src_rect.height = vin->format.height;
>
> + /* Make use of the hardware interlacer by default. */
> + if (vin->format.field == V4L2_FIELD_ALTERNATE) {
> + vin->format.field = V4L2_FIELD_INTERLACED;
> + vin->format.height *= 2;
> + }
> +
> + rvin_format_align(vin, &vin->format);
> +
> vin->crop = vin->src_rect;
> - vin->compose = vin->src_rect;
> +
> + vin->compose.top = 0;
> + vin->compose.left = 0;
> + vin->compose.width = vin->format.width;
> + vin->compose.height = vin->format.height;
>
> return 0;
> }
> @@ -217,13 +219,6 @@ static int rvin_try_format(struct rvin_dev *vin, u32 which,
> crop->left = 0;
> crop->width = pix->width;
> crop->height = pix->height;
> -
> - /*
> - * If source is ALTERNATE the driver will use the VIN hardware
> - * to INTERLACE it. The crop height then needs to be doubled.
> - */
> - if (pix->field == V4L2_FIELD_ALTERNATE)
> - crop->height *= 2;
> }
>
> if (field != V4L2_FIELD_ANY)
>
next prev parent reply other threads:[~2019-09-13 13:35 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-04 21:54 [PATCH v3 0/6] rcar-vin: Add support for V4L2_FIELD_ALTERNATE Niklas Söderlund
2019-09-04 21:54 ` [PATCH v3 1/6] rcar-vin: Fix incorrect return statement in rvin_try_format() Niklas Söderlund
2019-09-13 13:20 ` Kieran Bingham
2019-09-04 21:54 ` [PATCH v3 2/6] rcar-vin: Make use of V4L2_FIELD_IS_INTERLACED() macro Niklas Söderlund
2019-09-13 13:22 ` Kieran Bingham
2019-09-04 21:54 ` [PATCH v3 3/6] rcar-vin: Rename rectangle holding the video source information Niklas Söderlund
2019-09-04 21:54 ` [PATCH v3 4/6] rcar-vin: Do not reset the crop and compose rectangles in s_fmt Niklas Söderlund
2019-09-04 21:54 ` [PATCH v3 5/6] rcar-vin: Add support for V4L2_FIELD_ALTERNATE Niklas Söderlund
2019-09-13 13:34 ` Kieran Bingham [this message]
2019-09-04 21:54 ` [PATCH v3 6/6] rcar-vin: Clean up how format is set on subdevice Niklas Söderlund
2019-09-27 7:46 ` [PATCH v3 0/6] rcar-vin: Add support for V4L2_FIELD_ALTERNATE Hans Verkuil
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=61fd1036-2d11-4761-6cab-93b70a44baf6@ideasonboard.com \
--to=kieran.bingham+renesas@ideasonboard.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=niklas.soderlund+renesas@ragnatech.se \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).