From: Atish Patra <atishp@atishpatra.org>
To: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: devicetree@vger.kernel.org, Albert Ou <aou@eecs.berkeley.edu>,
Cyril.Jean@microchip.com,
Daire McNamara <daire.mcnamara@microchip.com>,
Anup Patel <anup@brainfault.org>, Anup Patel <anup.patel@wdc.com>,
"linux-kernel@vger.kernel.org List"
<linux-kernel@vger.kernel.org>, Atish Patra <atish.patra@wdc.com>,
Rob Herring <robh+dt@kernel.org>,
Alistair Francis <alistair.francis@wdc.com>,
Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
linux-riscv <linux-riscv@lists.infradead.org>,
Padmarao Begari <padmarao.begari@microchip.com>
Subject: Re: [RFC PATCH 2/3] RISC-V: Initial DTS for Microchip ICICLE board
Date: Tue, 3 Nov 2020 07:08:33 -0800 [thread overview]
Message-ID: <CAOnJCU+Zj7JCHssg_+Vj3E1NhK_etXauDDbKK08v=C6o4gDv2g@mail.gmail.com> (raw)
In-Reply-To: <734904fe-975a-5908-d08c-266a5049deac@codethink.co.uk>
On Tue, Nov 3, 2020 at 2:59 AM Ben Dooks <ben.dooks@codethink.co.uk> wrote:
>
> On 30/10/2020 20:27, Atish Patra wrote:
> > On Fri, Oct 30, 2020 at 2:05 AM Anup Patel <anup@brainfault.org> wrote:
> >>
> >> On Thu, Oct 29, 2020 at 4:58 AM Atish Patra <atish.patra@wdc.com> wrote:
> >>>
> >>> Add initial DTS for Microchip ICICLE board having only
> >>> essential devcies (clocks, sdhci, ethernet, serial, etc).
> >>>
> >>> Signed-off-by: Atish Patra <atish.patra@wdc.com>
> >>> ---
> >>> arch/riscv/boot/dts/Makefile | 1 +
> >>> arch/riscv/boot/dts/microchip/Makefile | 2 +
> >>> .../microchip/microchip-icicle-kit-a000.dts | 313 ++++++++++++++++++
> >>
> >> I suggest we split this DTS into two parts:
> >> 1. SOC (microchip-polarfire.dtsi)
> >> 2. Board (microchip-icicle-kit-a000.dts)
> >>
> >> This will be much cleaner and aligned with what is done
> >> on other architectures.
> >>
> >
> > Sure. I will do that in v2.
> >
> >>> 3 files changed, 316 insertions(+)
> >>> create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> >>> create mode 100644 arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
> >>>
> >>> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> >>> index ca1f8cbd78c0..3ea94ea0a18a 100644
> >>> --- a/arch/riscv/boot/dts/Makefile
> >>> +++ b/arch/riscv/boot/dts/Makefile
> >>> @@ -1,5 +1,6 @@
> >>> # SPDX-License-Identifier: GPL-2.0
> >>> subdir-y += sifive
> >>> subdir-y += kendryte
> >>> +subdir-y += microchip
> >>>
> >>> obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> >>> diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> >>> new file mode 100644
> >>> index 000000000000..55ad77521304
> >>> --- /dev/null
> >>> +++ b/arch/riscv/boot/dts/microchip/Makefile
> >>> @@ -0,0 +1,2 @@
> >>> +# SPDX-License-Identifier: GPL-2.0
> >>> +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-icicle-kit-a000.dtb
> >>> diff --git a/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts b/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
> >>> new file mode 100644
> >>> index 000000000000..5848920af55c
> >>> --- /dev/null
> >>> +++ b/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
> >>> @@ -0,0 +1,313 @@
> >>> +// SPDX-License-Identifier: GPL-2.0+
> >>> +/* Copyright (c) 2020 Microchip Technology Inc */
> >>> +
> >>> +/dts-v1/;
> >>> +
> >>> +/* Clock frequency (in Hz) of the rtcclk */
> >>> +#define RTCCLK_FREQ 1000000
> >>> +
> >>> +/ {
> >>> + #address-cells = <2>;
> >>> + #size-cells = <2>;
> >>> + model = "Microchip PolarFire-SoC";
> >>> + compatible = "microchip,polarfire-soc";
> >>> +
> >>> + chosen {
> >>> + stdout-path = &serial0;
> >>> + };
> >>> +
> >>> + cpus {
> >>> + #address-cells = <1>;
> >>> + #size-cells = <0>;
> >>> + timebase-frequency = <RTCCLK_FREQ>;
> >>> +
> >>> + cpu@0 {
> >>> + clock-frequency = <0>;
> >>> + compatible = "sifive,rocket0", "riscv";
> >>> + device_type = "cpu";
> >>> + i-cache-block-size = <64>;
> >>> + i-cache-sets = <128>;
> >>> + i-cache-size = <16384>;
> >>> + reg = <0>;
> >>> + riscv,isa = "rv64imac";
> >>> + status = "disabled";
> >>> +
> >>> + cpu0_intc: interrupt-controller {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "riscv,cpu-intc";
> >>> + interrupt-controller;
> >>> + };
> >>> + };
> >>> +
> >>> + cpu@1 {
> >>> + clock-frequency = <0>;
> >>> + compatible = "sifive,rocket0", "riscv";
> >>> + d-cache-block-size = <64>;
> >>> + d-cache-sets = <64>;
> >>> + d-cache-size = <32768>;
> >>> + d-tlb-sets = <1>;
> >>> + d-tlb-size = <32>;
> >>> + device_type = "cpu";
> >>> + i-cache-block-size = <64>;
> >>> + i-cache-sets = <64>;
> >>> + i-cache-size = <32768>;
> >>> + i-tlb-sets = <1>;
> >>> + i-tlb-size = <32>;
> >>> + mmu-type = "riscv,sv39";
> >>> + reg = <1>;
> >>> + riscv,isa = "rv64imafdc";
> >>> + tlb-split;
> >>> + status = "okay";
> >>> +
> >>> + cpu1_intc: interrupt-controller {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "riscv,cpu-intc";
> >>> + interrupt-controller;
> >>> + };
> >>> + };
> >>> +
> >>> + cpu@2 {
> >>> + clock-frequency = <0>;
> >>> + compatible = "sifive,rocket0", "riscv";
> >>> + d-cache-block-size = <64>;
> >>> + d-cache-sets = <64>;
> >>> + d-cache-size = <32768>;
> >>> + d-tlb-sets = <1>;
> >>> + d-tlb-size = <32>;
> >>> + device_type = "cpu";
> >>> + i-cache-block-size = <64>;
> >>> + i-cache-sets = <64>;
> >>> + i-cache-size = <32768>;
> >>> + i-tlb-sets = <1>;
> >>> + i-tlb-size = <32>;
> >>> + mmu-type = "riscv,sv39";
> >>> + reg = <2>;
> >>> + riscv,isa = "rv64imafdc";
> >>> + tlb-split;
> >>> + status = "okay";
> >>> +
> >>> + cpu2_intc: interrupt-controller {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "riscv,cpu-intc";
> >>> + interrupt-controller;
> >>> + };
> >>> + };
> >>> +
> >>> + cpu@3 {
> >>> + clock-frequency = <0>;
> >>> + compatible = "sifive,rocket0", "riscv";
> >>> + d-cache-block-size = <64>;
> >>> + d-cache-sets = <64>;
> >>> + d-cache-size = <32768>;
> >>> + d-tlb-sets = <1>;
> >>> + d-tlb-size = <32>;
> >>> + device_type = "cpu";
> >>> + i-cache-block-size = <64>;
> >>> + i-cache-sets = <64>;
> >>> + i-cache-size = <32768>;
> >>> + i-tlb-sets = <1>;
> >>> + i-tlb-size = <32>;
> >>> + mmu-type = "riscv,sv39";
> >>> + reg = <3>;
> >>> + riscv,isa = "rv64imafdc";
> >>> + tlb-split;
> >>> + status = "okay";
> >>> +
> >>> + cpu3_intc: interrupt-controller {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "riscv,cpu-intc";
> >>> + interrupt-controller;
> >>> + };
> >>> + };
> >>> +
> >>> + cpu@4 {
> >>> + clock-frequency = <0>;
> >>> + compatible = "sifive,rocket0", "riscv";
> >>> + d-cache-block-size = <64>;
> >>> + d-cache-sets = <64>;
> >>> + d-cache-size = <32768>;
> >>> + d-tlb-sets = <1>;
> >>> + d-tlb-size = <32>;
> >>> + device_type = "cpu";
> >>> + i-cache-block-size = <64>;
> >>> + i-cache-sets = <64>;
> >>> + i-cache-size = <32768>;
> >>> + i-tlb-sets = <1>;
> >>> + i-tlb-size = <32>;
> >>> + mmu-type = "riscv,sv39";
> >>> + reg = <4>;
> >>> + riscv,isa = "rv64imafdc";
> >>> + tlb-split;
> >>> + status = "okay";
> >>> + cpu4_intc: interrupt-controller {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "riscv,cpu-intc";
> >>> + interrupt-controller;
> >>> + };
> >>> + };
> >>> + };
> >>> +
> >>> + memory@80000000 {
> >>> + device_type = "memory";
> >>> + reg = <0x0 0x80000000 0x0 0x40000000>;
> >>> + clocks = <&clkcfg 26>;
> >>> + };
> >>> +
> >>> + soc {
> >>> + #address-cells = <2>;
> >>> + #size-cells = <2>;
> >>> + compatible = "simple-bus";
> >>> + ranges;
> >>> +
> >>> + cache-controller@2010000 {
> >>> + compatible = "sifive,fu540-c000-ccache", "cache";
> >>> + cache-block-size = <64>;
> >>> + cache-level = <2>;
> >>> + cache-sets = <1024>;
> >>> + cache-size = <2097152>;
> >>> + cache-unified;
> >>> + interrupt-parent = <&plic>;
> >>> + interrupts = <1 2 3>;
> >>> + reg = <0x0 0x2010000 0x0 0x1000>;
> >>> + };
> >>> +
> >>> + clint@2000000 {
> >>> + compatible = "riscv,clint0";
> >>> + reg = <0x0 0x2000000 0x0 0xC000>;
> >>> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> >>> + &cpu1_intc 3 &cpu1_intc 7
> >>> + &cpu2_intc 3 &cpu2_intc 7
> >>> + &cpu3_intc 3 &cpu3_intc 7
> >>> + &cpu4_intc 3 &cpu4_intc 7>;
> >>> + };
> >>> +
> >>> + plic: interrupt-controller@c000000 {
> >>> + #interrupt-cells = <1>;
> >>> + compatible = "sifive,plic-1.0.0";
> >>> + reg = <0x0 0xc000000 0x0 0x4000000>;
> >>> + riscv,ndev = <53>;
> >>> + interrupt-controller;
> >>> + interrupts-extended = <&cpu0_intc 11
> >>> + &cpu1_intc 11 &cpu1_intc 9
> >>> + &cpu2_intc 11 &cpu2_intc 9
> >>> + &cpu3_intc 11 &cpu3_intc 9
> >>> + &cpu4_intc 11 &cpu4_intc 9>;
> >>> + };
> >>> +
> >>> + dma@3000000 {
> >>> + compatible = "sifive,fu540-c000-pdma";
> >>> + reg = <0x0 0x3000000 0x0 0x8000>;
> >>> + interrupt-parent = <&plic>;
> >>> + interrupts = <23 24 25 26 27 28 29 30>;
> >>> + #dma-cells = <1>;
> >>> + };
> >>> +
> >>> + refclk: refclk {
> >>> + compatible = "fixed-clock";
> >>> + #clock-cells = <0>;
> >>> + clock-frequency = <600000000>;
> >>> + clock-output-names = "msspllclk";
> >>> + };
> >>> +
> >>> + clkcfg: clkcfg@20002000 {
> >>> + compatible = "microchip,pfsoc-clkcfg";
> >>> + reg = <0x0 0x20002000 0x0 0x1000>;
> >>> + reg-names = "mss_sysreg";
> >>> + clocks = <&refclk>;
> >>> + #clock-cells = <1>;
> >>> + clock-output-names = "cpuclk", "axiclk", "ahbclk", "ENVMclk", "MAC0clk", "MAC1clk", "MMCclk", "TIMERclk", "MMUART0clk", "MMUART1clk", "MMUART2clk", "MMUART3clk", "MMUART4clk", "SPI0clk", "SPI1clk", "I2C0clk", "I2C1clk", "CAN0clk", "CAN1clk", "USBclk", "RESERVED", "RTCclk", "QSPIclk", "GPIO0clk", "GPIO1clk", "GPIO2clk", "DDRCclk", "FIC0clk", "FIC1clk", "FIC2clk", "FIC3clk", "ATHENAclk", "CFMclk";
> >>> + };
> >>> +
>
> H ow about doing something like
> > clock-output-names = "cpuclk", "axiclk", "ahbclk", "ENVMclk", "MAC0clk", /* 0 -4 */
> > "MAC1clk", "MMCclk", "TIMERclk", "MMUART0clk", "MMUART1clk", /* 5-9 */
>
> this means we can easily work out what clocks are in which index
>
> As per the previos email, I'd leave these all populated as coming back
> and adding ones later is just going to be a pain with merge conflicts.
>
Sounds good to me.
>
>
> --
> Ben Dooks http://www.codethink.co.uk/
> Senior Engineer Codethink - Providing Genius
>
> https://www.codethink.co.uk/privacy.html
--
Regards,
Atish
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2020-11-03 15:09 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-28 23:27 [RFC PATCH 0/3] Add Microchip PolarFire Soc Support Atish Patra
2020-10-28 23:27 ` [RFC PATCH 1/3] RISC-V: Add Microchip PolarFire SoC kconfig option Atish Patra
2020-10-30 9:08 ` Anup Patel
2020-11-03 9:55 ` Bin Meng
2020-11-06 7:14 ` Palmer Dabbelt
2020-10-28 23:27 ` [RFC PATCH 2/3] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
2020-10-29 10:24 ` Ben Dooks
2020-10-30 7:11 ` Atish Patra
2020-10-30 21:19 ` Ben Dooks
2020-11-03 15:07 ` Atish Patra
2020-11-03 15:19 ` Ben Dooks
2020-11-03 18:10 ` Cyril.Jean
2020-11-03 18:28 ` Ben Dooks
2020-11-03 18:36 ` Atish Patra
2020-11-03 18:39 ` Ben Dooks
2020-11-03 18:45 ` Atish Patra
2020-11-03 18:40 ` Cyril.Jean
2020-11-03 18:46 ` Ben Dooks
2020-11-04 2:41 ` Bin Meng
2020-10-30 9:05 ` Anup Patel
2020-10-30 20:27 ` Atish Patra
2020-11-03 10:59 ` Ben Dooks
2020-11-03 15:08 ` Atish Patra [this message]
2020-10-30 21:20 ` Ben Dooks
2020-11-03 10:00 ` Bin Meng
2020-11-03 18:19 ` Cyril.Jean
2020-11-03 18:38 ` Atish Patra
2020-11-03 18:50 ` Cyril.Jean
2020-11-03 19:02 ` Atish Patra
2020-11-06 7:14 ` Palmer Dabbelt
2020-10-28 23:27 ` [RFC PATCH 3/3] RISC-V: Enable Microchip PolarFire ICICLE SoC Atish Patra
2020-10-30 9:09 ` Anup Patel
2020-10-30 21:21 ` Ben Dooks
2020-11-03 10:03 ` Bin Meng
2020-11-06 7:14 ` Palmer Dabbelt
2020-11-06 7:14 ` [RFC PATCH 0/3] Add Microchip PolarFire Soc Support Palmer Dabbelt
2020-11-06 7:37 ` Atish Patra
2020-11-06 8:11 ` Palmer Dabbelt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAOnJCU+Zj7JCHssg_+Vj3E1NhK_etXauDDbKK08v=C6o4gDv2g@mail.gmail.com' \
--to=atishp@atishpatra.org \
--cc=Cyril.Jean@microchip.com \
--cc=alistair.francis@wdc.com \
--cc=anup.patel@wdc.com \
--cc=anup@brainfault.org \
--cc=aou@eecs.berkeley.edu \
--cc=atish.patra@wdc.com \
--cc=ben.dooks@codethink.co.uk \
--cc=daire.mcnamara@microchip.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=padmarao.begari@microchip.com \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).