From: Chen-Yu Tsai <wens@csie.org>
To: Maxime Ripard <maxime.ripard@bootlin.com>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
Alessandro Zummo <a.zummo@towertech.it>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Cc: Chen-Yu Tsai <wens@csie.org>,
linux-arm-kernel@lists.infradead.org, linux-rtc@vger.kernel.org,
linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-sunxi@googlegroups.com,
Corentin Labbe <clabbe.montjoie@gmail.com>
Subject: [PATCH v2 02/14] dt-bindings: rtc: sun6i-rtc: Add compatible strings for pre-H6 variants
Date: Mon, 3 Dec 2018 22:58:13 +0800 [thread overview]
Message-ID: <20181203145825.20511-3-wens@csie.org> (raw)
In-Reply-To: <20181203145825.20511-1-wens@csie.org>
While doing Bluetooth enablement for various boards based on various
Allwinner SoCs, minor differences in the RTC modules were found. These
include a lack of an external clock output (A31), different internal
oscillator frequencies (H3/H5/A64/V3/V3s), different regulator voltage
settings (H5/H6), and the presence of miscellaneous registers unrelated
to the RTC (A64/R40/H5/H6). The datasheet also describes different number
of registers for non-volatile storage, though based on actual experiments
the actual number is the same across the board.
This patch adds a list of all pre-H6 variants, grouped by the internal
oscillator's clock rate, regulator settings, and the presence of the
external clock output. Combinations are introduced for the variants that
have miscellaneous registers.
The RTC block in the H6 also handles the 24 MHz DCXO. This will require
more device tree binding changes and will be done later.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
.../devicetree/bindings/rtc/sun6i-rtc.txt | 16 +++++++++++++++-
1 file changed, 15 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
index fed0d58cbfec..037ec475f412 100644
--- a/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/sun6i-rtc.txt
@@ -3,7 +3,21 @@
RTC controller for the Allwinner A31
Required properties:
-- compatible : Should be "allwinner,sun6i-a31-rtc"
+- compatible : Should be one of the following combinations:
+ - "allwinner,sun6i-a31-rtc"
+ - "allwinner,sun8i-a23-rtc"
+ - "allwinner,sun8i-h3-rtc"
+ - "allwinner,sun8i-r40-rtc", "allwinner,sun8i-h3-rtc"
+ - "allwinner,sun8i-v3-rtc"
+ - "allwinner,sun50i-a64-rtc", "allwinner,sun8i-h3-rtc"
+ - "allwinner,sun50i-h5-rtc"
+
+ Where there are two or more compatible strings, this
+ denotes the hardware covered by the most specific one
+ is backward-compatible with the latter ones, and the
+ implementation for the latter ones can be used, albeit
+ with reduced functionality.
+
- reg : physical base address of the controller and length of
memory mapped region.
- interrupts : IRQ lines for the RTC alarm 0 and alarm 1, in that order.
--
2.20.0.rc1
next prev parent reply other threads:[~2018-12-03 14:59 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-03 14:58 [PATCH v2 00/14] rtc: sun6i: clock rework and pre-H6 SoC support Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 01/14] dt-bindings: rtc: sun6i-rtc: Rewrite clock outputs as a list Chen-Yu Tsai
2018-12-03 14:58 ` Chen-Yu Tsai [this message]
2018-12-03 14:58 ` [PATCH v2 03/14] dt-bindings: rtc: sun6i-rtc: Deprecate external clock output for A31 Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 04/14] dt-bindings: rtc: sun6i-rtc: Export internal RC oscillator Chen-Yu Tsai
2018-12-04 9:17 ` Maxime Ripard
2018-12-03 14:58 ` [PATCH v2 05/14] rtc: sun6i: Add default clock name for LOSC Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 06/14] rtc: sun6i: Add support for different variants Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 07/14] rtc: sun6i: Add support for all known pre-H6 variants Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 08/14] rtc: sun6i: Expose internal oscillator through device tree Chen-Yu Tsai
2018-12-04 9:17 ` Maxime Ripard
2018-12-03 14:58 ` [PATCH v2 09/14] ARM: dts: sun8i: a23/a33: Fix up RTC device node Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 10/14] ARM: dts: sunxi: h3/h5: Add clock accuracy for external oscillators Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 11/14] ARM: dts: sunxi: h3/h5: Fix up RTC device node and clock references Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 12/14] ARM: dts: sun8i: r40: Add clock accuracy for external oscillators Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 13/14] ARM: dts: sun8i: r40: Add RTC device node Chen-Yu Tsai
2018-12-03 14:58 ` [PATCH v2 14/14] arm64: dts: allwinner: a64: Fix up RTC device node and clock references Chen-Yu Tsai
2018-12-06 5:49 ` [PATCH v2 00/14] rtc: sun6i: clock rework and pre-H6 SoC support Chen-Yu Tsai
2018-12-06 20:34 ` Alexandre Belloni
2018-12-07 2:25 ` Chen-Yu Tsai
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181203145825.20511-3-wens@csie.org \
--to=wens@csie.org \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@bootlin.com \
--cc=clabbe.montjoie@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rtc@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=maxime.ripard@bootlin.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).