Re: [PATCH V7] GCOV: Add config to check the preqequisites situation

[Cixi Geng <gengcixi@gmail.com>]

Hi ALL：
Not recieve more advise for a long time ,
Can this submission be merged recently?

Cixi Geng <gengcixi@gmail.com> 于2020年8月20日周四 下午8:40写道：
>
> Hi All:
>
> Does this patch need more modification?
>
> <gengcixi@gmail.com> 于2020年7月27日周一 下午4:51写道：
> >
> > From: Cixi Geng <cixi.geng1@unisoc.com>
> >
> > Introduce new configuration option GCOV_PROFILE_PREREQS that can be
> > used to check whether the prerequisites for enabling gcov profiling
> > for specific files and directories are met.
> >
> > Only add SERIAL_GCOV for an example.
> >
> > Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
> > ---
> >  drivers/tty/serial/Kconfig  |  7 +++++++
> >  drivers/tty/serial/Makefile |  1 +
> >  kernel/gcov/Kconfig         | 12 ++++++++++++
> >  3 files changed, 20 insertions(+)
> >
> > diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> > index 780908d43557..55b128b6b31d 100644
> > --- a/drivers/tty/serial/Kconfig
> > +++ b/drivers/tty/serial/Kconfig
> > @@ -1576,3 +1576,10 @@ endmenu
> >
> >  config SERIAL_MCTRL_GPIO
> >         tristate
> > +
> > +config SERIAL_GCOV
> > +       bool "Enable profile gcov for serial directory"
> > +       depends on GCOV_PROFILE_PREREQS
> > +       help
> > +         The SERIAL_GCOV will add Gcov profiling flags when kernel compiles.
> > +         Say 'Y' here if you want the gcov data for the serial directory,
> > diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> > index d056ee6cca33..17272733db95 100644
> > --- a/drivers/tty/serial/Makefile
> > +++ b/drivers/tty/serial/Makefile
> > @@ -3,6 +3,7 @@
> >  # Makefile for the kernel serial device drivers.
> >  #
> >
> > +GCOV_PROFILE := $(CONFIG_SERIAL_GCOV)
> >  obj-$(CONFIG_SERIAL_CORE) += serial_core.o
> >
> >  obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
> > diff --git a/kernel/gcov/Kconfig b/kernel/gcov/Kconfig
> > index 3110c77230c7..bb2e1fb85743 100644
> > --- a/kernel/gcov/Kconfig
> > +++ b/kernel/gcov/Kconfig
> > @@ -51,4 +51,16 @@ config GCOV_PROFILE_ALL
> >         larger and run slower. Also be sure to exclude files from profiling
> >         which are not linked to the kernel image to prevent linker errors.
> >
> > +config GCOV_PROFILE_PREREQS
> > +       bool "Profile Kernel for prereqs"
> > +       depends on GCOV_KERNEL
> > +       depends on  !COMPILE_TEST
> > +       def_bool y if GCOV_KERNEL && !COMPILE_TEST
> > +       help
> > +         This options activates profiling for the specified kernel modules.
> > +
> > +         When some modules need Gcov data, enable this config, then configure
> > +         with gcov on the corresponding modules,The directories or files of
> > +         these modules will be added profiling flags after kernel compile.
> > +
> >  endmenu
> > --
> > 2.17.1
> >