linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Douglas Anderson <dianders@chromium.org>
To: Mark Brown <broonie@kernel.org>, Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: akashast@codeaurora.org, linux-arm-msm@vger.kernel.org,
	mkshah@codeaurora.org, swboyd@chromium.org,
	georgi.djakov@linaro.org, ctheegal@codeaurora.org,
	mka@chromium.org, Douglas Anderson <dianders@chromium.org>,
	linux-kernel@vger.kernel.org, linux-spi@vger.kernel.org
Subject: [PATCH 3/3] spi: spi-geni-qcom: Get rid of most overhead in prepare_message()
Date: Wed,  1 Jul 2020 17:45:09 -0700	[thread overview]
Message-ID: <20200701174506.3.I2b3d7aeb1ea622335482cce60c58d2f8381e61dd@changeid> (raw)
In-Reply-To: <20200702004509.2333554-1-dianders@chromium.org>

There's a bunch of overhead in spi-geni-qcom's prepare_message.  Get
rid of it.  Before this change spi_geni_prepare_message() took around
14.5 us.  After this change, spi_geni_prepare_message() takes about
1.75 us (as measured by ftrace).

What's here:
* We're always in FIFO mode, so no need to call it for every transfer.
  This avoids a whole ton of readl/writel calls.
* We don't need to write a whole pile of config registers if the mode
  isn't changing.  Cache the last mode and only do the work if needed.
* For several registers we were trying to do read/modify/write, but
  there was no reason.  The registers only have one thing in them, so
  just write them.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
---

 drivers/spi/spi-geni-qcom.c | 54 +++++++++++++++++--------------------
 1 file changed, 24 insertions(+), 30 deletions(-)

diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index f51279608fc7..97fac5ea6afd 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -77,6 +77,7 @@ struct spi_geni_master {
 	u32 tx_fifo_depth;
 	u32 fifo_width_bits;
 	u32 tx_wm;
+	u32 last_mode;
 	unsigned long cur_speed_hz;
 	unsigned int cur_bits_per_word;
 	unsigned int tx_rem_bytes;
@@ -177,8 +178,6 @@ static void spi_setup_word_len(struct spi_geni_master *mas, u16 mode,
 	struct geni_se *se = &mas->se;
 	u32 word_len;
 
-	word_len = readl(se->base + SE_SPI_WORD_LEN);
-
 	/*
 	 * If bits_per_word isn't a byte aligned value, set the packing to be
 	 * 1 SPI word per FIFO word.
@@ -187,10 +186,9 @@ static void spi_setup_word_len(struct spi_geni_master *mas, u16 mode,
 		pack_words = mas->fifo_width_bits / bits_per_word;
 	else
 		pack_words = 1;
-	word_len &= ~WORD_LEN_MSK;
-	word_len |= ((bits_per_word - MIN_WORD_LEN) & WORD_LEN_MSK);
 	geni_se_config_packing(&mas->se, bits_per_word, pack_words, msb_first,
 								true, true);
+	word_len = (bits_per_word - MIN_WORD_LEN) & WORD_LEN_MSK;
 	writel(word_len, se->base + SE_SPI_WORD_LEN);
 }
 
@@ -238,38 +236,34 @@ static int setup_fifo_params(struct spi_device *spi_slv,
 {
 	struct spi_geni_master *mas = spi_master_get_devdata(spi);
 	struct geni_se *se = &mas->se;
-	u32 loopback_cfg, cpol, cpha, demux_output_inv;
+	u32 loopback_cfg = 0, cpol = 0, cpha = 0, demux_output_inv = 0;
 	u32 demux_sel;
 
-	loopback_cfg = readl(se->base + SE_SPI_LOOPBACK);
-	cpol = readl(se->base + SE_SPI_CPOL);
-	cpha = readl(se->base + SE_SPI_CPHA);
-	demux_output_inv = 0;
-	loopback_cfg &= ~LOOPBACK_MSK;
-	cpol &= ~CPOL;
-	cpha &= ~CPHA;
+	if (mas->last_mode != spi_slv->mode) {
+		if (spi_slv->mode & SPI_LOOP)
+			loopback_cfg = LOOPBACK_ENABLE;
 
-	if (spi_slv->mode & SPI_LOOP)
-		loopback_cfg |= LOOPBACK_ENABLE;
+		if (spi_slv->mode & SPI_CPOL)
+			cpol = CPOL;
 
-	if (spi_slv->mode & SPI_CPOL)
-		cpol |= CPOL;
+		if (spi_slv->mode & SPI_CPHA)
+			cpha = CPHA;
 
-	if (spi_slv->mode & SPI_CPHA)
-		cpha |= CPHA;
+		if (spi_slv->mode & SPI_CS_HIGH)
+			demux_output_inv = BIT(spi_slv->chip_select);
 
-	if (spi_slv->mode & SPI_CS_HIGH)
-		demux_output_inv = BIT(spi_slv->chip_select);
+		demux_sel = spi_slv->chip_select;
+		mas->cur_bits_per_word = spi_slv->bits_per_word;
 
-	demux_sel = spi_slv->chip_select;
-	mas->cur_bits_per_word = spi_slv->bits_per_word;
+		spi_setup_word_len(mas, spi_slv->mode, spi_slv->bits_per_word);
+		writel(loopback_cfg, se->base + SE_SPI_LOOPBACK);
+		writel(demux_sel, se->base + SE_SPI_DEMUX_SEL);
+		writel(cpha, se->base + SE_SPI_CPHA);
+		writel(cpol, se->base + SE_SPI_CPOL);
+		writel(demux_output_inv, se->base + SE_SPI_DEMUX_OUTPUT_INV);
 
-	spi_setup_word_len(mas, spi_slv->mode, spi_slv->bits_per_word);
-	writel(loopback_cfg, se->base + SE_SPI_LOOPBACK);
-	writel(demux_sel, se->base + SE_SPI_DEMUX_SEL);
-	writel(cpha, se->base + SE_SPI_CPHA);
-	writel(cpol, se->base + SE_SPI_CPOL);
-	writel(demux_output_inv, se->base + SE_SPI_DEMUX_OUTPUT_INV);
+		mas->last_mode = spi_slv->mode;
+	}
 
 	return geni_spi_set_clock_and_bw(mas, spi_slv->max_speed_hz);
 }
@@ -279,9 +273,7 @@ static int spi_geni_prepare_message(struct spi_master *spi,
 {
 	int ret;
 	struct spi_geni_master *mas = spi_master_get_devdata(spi);
-	struct geni_se *se = &mas->se;
 
-	geni_se_select_mode(se, GENI_SE_FIFO);
 	ret = setup_fifo_params(spi_msg->spi, spi);
 	if (ret)
 		dev_err(mas->dev, "Couldn't select mode %d\n", ret);
@@ -322,6 +314,8 @@ static int spi_geni_init(struct spi_geni_master *mas)
 	else
 		mas->oversampling = 1;
 
+	geni_se_select_mode(se, GENI_SE_FIFO);
+
 	pm_runtime_put(mas->dev);
 	return 0;
 }
-- 
2.27.0.383.g050319c2ae-goog


  parent reply	other threads:[~2020-07-02  0:45 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-02  0:45 [PATCH 0/3] spi: spi-geni-qcom: Avoid a bunch of per-transfer overhead Douglas Anderson
2020-07-02  0:45 ` [PATCH 1/3] spi: spi-geni-qcom: Avoid clock setting if not needed Douglas Anderson
2020-07-07 10:16   ` Akash Asthana
2020-07-07 12:08   ` Mark Brown
2020-07-07 12:53     ` Doug Anderson
2020-07-08 10:01       ` Mark Brown
2020-07-08 15:22         ` Doug Anderson
2020-07-08 17:02           ` Mark Brown
2020-07-08 12:48   ` Mark Brown
2020-07-02  0:45 ` [PATCH 2/3] spi: spi-geni-qcom: Set an autosuspend delay of 250 ms Douglas Anderson
2020-07-07 10:18   ` Akash Asthana
2020-07-02  0:45 ` Douglas Anderson [this message]
2020-07-07 13:37   ` [PATCH 3/3] spi: spi-geni-qcom: Get rid of most overhead in prepare_message() Akash Asthana
2020-07-08 12:49   ` Mark Brown
2020-07-07 14:17 ` [PATCH 0/3] spi: spi-geni-qcom: Avoid a bunch of per-transfer overhead Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200701174506.3.I2b3d7aeb1ea622335482cce60c58d2f8381e61dd@changeid \
    --to=dianders@chromium.org \
    --cc=agross@kernel.org \
    --cc=akashast@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=broonie@kernel.org \
    --cc=ctheegal@codeaurora.org \
    --cc=georgi.djakov@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=mka@chromium.org \
    --cc=mkshah@codeaurora.org \
    --cc=swboyd@chromium.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).