From: Andre Przywara <andre.przywara@arm.com>
To: Jagan Teki <jagan@amarulasolutions.com>, Peng Fan <peng.fan@nxp.com>
Cc: u-boot@lists.denx.de, Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>,
Ondrej Jirman <megous@megous.com>,
linux-sunxi@lists.linux.dev
Subject: [PATCH 8/8] mmc: sunxi: Use mmc_of_parse()
Date: Tue, 25 May 2021 00:30:29 +0100 [thread overview]
Message-ID: <20210524233029.16417-9-andre.przywara@arm.com> (raw)
In-Reply-To: <20210524233029.16417-1-andre.przywara@arm.com>
At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/mmc/sunxi_mmc.c | 32 +++++++++++++++++---------------
1 file changed, 17 insertions(+), 15 deletions(-)
diff --git a/drivers/mmc/sunxi_mmc.c b/drivers/mmc/sunxi_mmc.c
index 115b519546e..178b8cf106d 100644
--- a/drivers/mmc/sunxi_mmc.c
+++ b/drivers/mmc/sunxi_mmc.c
@@ -37,7 +37,6 @@ struct sunxi_mmc_priv {
uint32_t *mclkreg;
unsigned fatal_err;
struct gpio_desc cd_gpio; /* Change Detect GPIO */
- int cd_inverted; /* Inverted Card Detect */
struct sunxi_mmc *reg;
struct mmc_config cfg;
};
@@ -612,12 +611,21 @@ static int sunxi_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd,
static int sunxi_mmc_getcd(struct udevice *dev)
{
+ struct mmc *mmc = mmc_get_mmc_dev(dev);
struct sunxi_mmc_priv *priv = dev_get_priv(dev);
+ /* If polling, assume that the card is always present. */
+ if ((mmc->cfg->host_caps & MMC_CAP_NONREMOVABLE) ||
+ (mmc->cfg->host_caps & MMC_CAP_NEEDS_POLL))
+ return 1;
+
if (dm_gpio_is_valid(&priv->cd_gpio)) {
int cd_state = dm_gpio_get_value(&priv->cd_gpio);
- return cd_state ^ priv->cd_inverted;
+ if (mmc->cfg->host_caps & MMC_CAP_CD_ACTIVE_HIGH)
+ return !cd_state;
+ else
+ return cd_state;
}
return 1;
}
@@ -649,23 +657,21 @@ static int sunxi_mmc_probe(struct udevice *dev)
struct mmc_config *cfg = &plat->cfg;
struct ofnode_phandle_args args;
u32 *ccu_reg;
- int bus_width, ret;
+ int ret;
cfg->name = dev->name;
- bus_width = dev_read_u32_default(dev, "bus-width", 1);
cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34;
- cfg->host_caps = 0;
- if (bus_width == 8)
- cfg->host_caps |= MMC_MODE_8BIT;
- if (bus_width >= 4)
- cfg->host_caps |= MMC_MODE_4BIT;
- cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS;
+ cfg->host_caps = MMC_MODE_HS_52MHz | MMC_MODE_HS;
cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT;
cfg->f_min = 400000;
cfg->f_max = 52000000;
+ ret = mmc_of_parse(dev, cfg);
+ if (ret)
+ return ret;
+
priv->reg = dev_read_addr_ptr(dev);
/* We don't have a sunxi clock driver so find the clock address here */
@@ -691,17 +697,13 @@ static int sunxi_mmc_probe(struct udevice *dev)
return ret;
/* This GPIO is optional */
- if (!dev_read_bool(dev, "non-removable") &&
- !gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
+ if (!gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio,
GPIOD_IS_IN)) {
int cd_pin = gpio_get_number(&priv->cd_gpio);
sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP);
}
- /* Check if card detect is inverted */
- priv->cd_inverted = dev_read_bool(dev, "cd-inverted");
-
upriv->mmc = &plat->mmc;
/* Reset controller */
--
2.17.5
next prev parent reply other threads:[~2021-05-24 23:31 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-05-24 23:30 [PATCH 0/8] sunxi: mmc: Fixes and speed increase Andre Przywara
2021-05-24 23:30 ` [PATCH 1/8] mmc: sunxi: Avoid #ifdefs in delay and width setup Andre Przywara
2021-05-25 1:42 ` Jaehoon Chung
2021-05-24 23:30 ` [PATCH 2/8] mmc: sunxi: Fix warnings with CONFIG_PHYS_64BIT Andre Przywara
2021-05-25 1:43 ` Jaehoon Chung
2021-05-24 23:30 ` [PATCH 3/8] mmc: sunxi: Fix MMC clock parent selection Andre Przywara
2021-05-24 23:30 ` [PATCH 4/8] mmc: sunxi: Cleanup "new timing mode" selection Andre Przywara
2021-05-25 1:43 ` Jaehoon Chung
2021-05-24 23:30 ` [PATCH 5/8] mmc: sunxi: Enable "new timing mode" on all new SoCs Andre Przywara
2021-05-24 23:30 ` [PATCH 6/8] mmc: sunxi: Cleanup and fix self-calibration code Andre Przywara
2021-05-24 23:30 ` [PATCH 7/8] mmc: sunxi: Increase MMIO FIFO read performance Andre Przywara
2021-05-24 23:30 ` Andre Przywara [this message]
2021-05-25 1:43 ` [PATCH 8/8] mmc: sunxi: Use mmc_of_parse() Jaehoon Chung
2021-07-03 23:24 ` [PATCH 0/8] sunxi: mmc: Fixes and speed increase Andre Przywara
2021-07-04 19:56 ` Samuel Holland
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210524233029.16417-9-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=jagan@amarulasolutions.com \
--cc=jernej.skrabec@gmail.com \
--cc=linux-sunxi@lists.linux.dev \
--cc=megous@megous.com \
--cc=peng.fan@nxp.com \
--cc=samuel@sholland.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).