Re: [PATCH v2 00/14] usb: dwc2: Fix Partial Power down issues.

[Artur Petrosyan <Arthur.Petrosyan@synopsys.com>]

Hi Greg,

On 4/8/2021 11:28, Artur Petrosyan wrote:
> This patch set fixes and improves the Partial Power Down mode for
> dwc2 core.
> It adds support for the following cases
>      1. Entering and exiting partial power down when a port is
>         suspended, resumed, port reset is asserted.
>      2. Exiting the partial power down mode before removing driver.
>      3. Exiting partial power down in wakeup detected interrupt handler.
>      4. Exiting from partial power down mode when connector ID.
>         status changes to "connId B
> 
> It updates and fixes the implementation of dwc2 entering and
> exiting partial power down mode when the system (PC) is suspended.
> 
> The patch set also improves the implementation of function handlers
> for entering and exiting host or device partial power down.
> 
> NOTE: This is the second patch set in the power saving mode fixes
> series.
> This patch set is part of multiple series and is continuation
> of the "usb: dwc2: Fix and improve power saving modes" patch set.
> (Patch set link: https://marc.info/?l=linux-usb&m=160379622403975&w=2).
> The patches that were included in the "usb: dwc2:
> Fix and improve power saving modes" which was submitted
> earlier was too large and needed to be split up into
> smaller patch sets.
> 
> Changes since V1:
> No changes in the patches or the source code.
> Sending the second version of the patch set because the first version
> was not received by vger.kernel.org.
> 
> 
> 
> Artur Petrosyan (14):
>    usb: dwc2: Add device partial power down functions
>    usb: dwc2: Add host partial power down functions
>    usb: dwc2: Update enter and exit partial power down functions
>    usb: dwc2: Add partial power down exit flow in wakeup intr.
>    usb: dwc2: Update port suspend/resume function definitions.
>    usb: dwc2: Add enter partial power down when port is suspended
>    usb: dwc2: Add exit partial power down when port is resumed
>    usb: dwc2: Add exit partial power down when port reset is asserted
>    usb: dwc2: Add part. power down exit from
>      dwc2_conn_id_status_change().
>    usb: dwc2: Allow exit partial power down in urb enqueue
>    usb: dwc2: Fix session request interrupt handler
>    usb: dwc2: Update partial power down entering by system suspend
>    usb: dwc2: Fix partial power down exiting by system resume
>    usb: dwc2: Add exit partial power down before removing driver
> 
>   drivers/usb/dwc2/core.c      | 113 ++-------
>   drivers/usb/dwc2/core.h      |  27 ++-
>   drivers/usb/dwc2/core_intr.c |  46 ++--
>   drivers/usb/dwc2/gadget.c    | 148 ++++++++++-
>   drivers/usb/dwc2/hcd.c       | 458 +++++++++++++++++++++++++----------
>   drivers/usb/dwc2/hw.h        |   1 +
>   drivers/usb/dwc2/platform.c  |  11 +-
>   7 files changed, 558 insertions(+), 246 deletions(-)
> 
> 
> base-commit: e9fcb07704fcef6fa6d0333fd2b3a62442eaf45b
> 

Re sending as a "v2" did not work :(.
The patches are not in lore again.

Could the issue be with a comma in the end of To: or Cc: list?
Let me remove the comma in the end of those lists and try sending as "v3".

Regards,
Artur