Hi, Kai Heng Feng writes: >> Oliver Neukum writes: >>> Am Dienstag, den 09.07.2019, 21:10 +0800 schrieb Kai-Heng Feng: >>>> Hi Mika and Mathias, >>>> >>>> I’ve filed a bug [1] which renders docking station unusable. >>>> >>>> I am not sure it's a bug in PCI, Thunderbolt or xHCI so raise the issue >>>> to >>>> you both. >>>> >>>> [1] https://bugzilla.kernel.org/show_bug.cgi?id=203885 >>>> >>>> Kai-Heng >>> >>> The issue starts before you unplug. In fact it starts before >>> the dock is even detected the first time: >>> >>> [ 13.171167] rfkill: input handler disabled >>> [ 19.781905] pcieport 0000:00:1c.0: PME: Spurious native interrupt! >>> [ 19.781909] pcieport 0000:00:1c.0: PME: Spurious native interrupt! >>> [ 20.109251] usb 4-1: new SuperSpeedPlus Gen 2 USB device number 2 >>> using xhci_hcd >>> [ 20.136000] usb 4-1: New USB device found, idVendor=0bda, >>> idProduct=0487, bcdDevice= 1.47 >>> [ 20.136004] usb 4-1: New USB device strings: Mfr=1, Product=2, >>> SerialNumber=0 >>> [ 20.136007] usb 4-1: Product: Dell dock >>> [ 20.136009] usb 4-1: Manufacturer: Dell Inc. >>> [ 20.140607] hub 4-1:1.0: USB hub found >>> [ 20.141004] hub 4-1:1.0: 4 ports detected >>> [ 20.253025] usb 1-4: new high-speed USB device number 5 using xhci_hcd >>> [ 20.403520] usb 1-4: New USB device found, idVendor=0bda, >>> idProduct=5487, bcdDevice= 1.47 >>> [ 20.403521] usb 1-4: New USB device strings: Mfr=1, Product=2, >>> SerialNumber=0 >>> [ 20.403522] usb 1-4: Product: Dell dock >>> [ 20.403522] usb 1-4: Manufacturer: Dell Inc. >>> [ 20.404348] hub 1-4:1.0: USB hub found >>> >>> This looks like a PCI issue. >>> In general, this kind of reporting sucks. We have to guess what you did >>> at 19.781905 >> >> It might be nice to know which device is generating that and why it's >> not found. This may help: >> >> diff --git a/drivers/pci/pcie/pme.c b/drivers/pci/pcie/pme.c >> index f38e6c19dd50..33285ef29362 100644 >> --- a/drivers/pci/pcie/pme.c >> +++ b/drivers/pci/pcie/pme.c >> @@ -203,7 +203,7 @@ static void pcie_pme_handle_request(struct pci_dev >> *port, u16 req_id) >> >> out: >> if (!found) >> - pci_info(port, "Spurious native interrupt!\n"); >> + pci_info(port, "Spurious native interrupt! (Bus# %d DevFn >> %d)\n", busnr, devfn); >> } >> >> /** >> >> >> Also, according to what Kai-Heng said, xHCI stops working even after >> repluggin the Dock. We could be dealing with two bugs here: >> >> 1. Spurious PME event being generated by an unexistent device >> 2. xHCI not handling hot-plug very well >> >> Kai-Heng, >> >> please run your tests again and make note of when you unplugged the dock >> and when you replugged it so we can correlate the time stampts with what >> you have done otherwise we will never be able to pin-point what's going >> on. > > I upgraded the system firmware, TBT firmware and docking station firmware > to latest, and used latest mainline kernel. > Now the issue can be reproduced at the very first time I plugged the > docking station. > > Attach dmesg to BKO since there are lots of message after XHCI dyndbg is > enabled. I saw that you annotated the plug, but not the unplug. Where does the unplug start? There are many places where it could be, but I need to be sure. Also, wasn't it so that the problem is when you *replug* the dock? So can you better describe what you're doing? Are you booting with dock connected then disconnect and reconnect or are you booting without dock and it fails on first plug? What are you consider a fail here? Can't you see the xhci bus? USB Devices don't show? What do you have on lsusb -t? Best regards -- balbi