Re: [PATCH v3] usb: Add a new quirk to let buggy hub enable and disable LPM during suspend and resume

[Kai-Heng Feng <kai.heng.feng@canonical.com>]

> On Oct 21, 2019, at 21:59, Mathias Nyman <mathias.nyman@linux.intel.com> wrote:
> 
> On 18.10.2019 21.59, Greg Kroah-Hartman wrote:
>> On Thu, Oct 17, 2019 at 02:33:00PM +0800, Kai-Heng Feng wrote:
>>> 
>>> 
>>>> On Oct 4, 2019, at 03:04, Alan Stern <stern@rowland.harvard.edu> wrote:
>>>> 
>>>> On Fri, 4 Oct 2019, Kai-Heng Feng wrote:
>>>> 
>>>>> Dell WD15 dock has a topology like this:
>>>>> /:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M
>>>>>    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/7p, 5000M
>>>>>            |__ Port 2: Dev 3, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M
>>>>> 
>>>>> Their IDs:
>>>>> Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
>>>>> Bus 004 Device 002: ID 0424:5537 Standard Microsystems Corp.
>>>>> Bus 004 Device 004: ID 0bda:8153 Realtek Semiconductor Corp.
>>>>> 
>>>>> Ethernet cannot be detected after plugging ethernet cable to the dock,
>>>>> the hub and roothub get runtime resumed and runtime suspended
>>>>> immediately:
>>>>> ...
>>>>> [  433.315169] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
>>>>> [  433.315204] usb usb4: usb auto-resume
>>>>> [  433.315226] hub 4-0:1.0: hub_resume
>>>>> [  433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
>>>>> [  433.315264] usb usb4-port1: status 0343 change 0001
>>>>> [  433.315279] xhci_hcd 0000:3a:00.0: clear port1 connect change, portsc: 0x10002e2
>>>>> [  433.315293] xhci_hcd 0000:3a:00.0: Get port status 4-2 read: 0x2a0, return 0x2a0
>>>>> [  433.317012] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
>>>>> [  433.422282] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
>>>>> 
>>>>> At this point the SMSC hub (usb 4-1) enters into compliance mode
>>>>> (USB_SS_PORT_LS_COMP_MOD), and USB core tries to warm-reset it,
>>>>> 
>>>>> [  433.422307] usb usb4-port1: do warm reset
>>>>> [  433.422311] usb 4-1: device reset not allowed in state 8
>>>>> [  433.422339] hub 4-0:1.0: state 7 ports 2 chg 0002 evt 0000
>>>>> [  433.422346] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10002e2, return 0x343
>>>>> [  433.422356] usb usb4-port1: do warm reset
>>>>> [  433.422358] usb 4-1: device reset not allowed in state 8
>>>>> [  433.422428] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 0 status  = 0xf0002e2
>>>>> [  433.422455] xhci_hcd 0000:3a:00.0: set port remote wake mask, actual port 1 status  = 0xe0002a0
>>>>> [  433.422465] hub 4-0:1.0: hub_suspend
>>>>> [  433.422475] usb usb4: bus auto-suspend, wakeup 1
>>>>> [  433.426161] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
>>>>> [  433.466209] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.510204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.554051] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.598235] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.642154] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.686204] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.730205] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.774203] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.818207] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.862040] xhci_hcd 0000:3a:00.0: port 0 polling in bus suspend, waiting
>>>>> [  433.862053] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
>>>>> [  433.862077] xhci_hcd 0000:3a:00.0: xhci_suspend: stopping port polling.
>>>>> [  433.862096] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
>>>>> [  433.862312] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_suspend: 0
>>>>> [  433.862445] xhci_hcd 0000:3a:00.0: PME# enabled
>>>>> [  433.902376] xhci_hcd 0000:3a:00.0: restoring config space at offset 0xc (was 0x0, writing 0x20)
>>>>> [  433.902395] xhci_hcd 0000:3a:00.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100403)
>>>>> [  433.902490] xhci_hcd 0000:3a:00.0: PME# disabled
>>>>> [  433.902504] xhci_hcd 0000:3a:00.0: enabling bus mastering
>>>>> [  433.902547] xhci_hcd 0000:3a:00.0: // Setting command ring address to 0x8578fc001
>>>>> [  433.902649] pcieport 0000:00:1b.0: PME: Spurious native interrupt!
>>>>> [  433.902839] xhci_hcd 0000:3a:00.0: Port change event, 4-1, id 3, portsc: 0xb0202e2
>>>>> [  433.902842] xhci_hcd 0000:3a:00.0: resume root hub
>>>>> [  433.902845] xhci_hcd 0000:3a:00.0: handle_port_status: starting port polling.
>>>>> [  433.902877] xhci_hcd 0000:3a:00.0: xhci_resume: starting port polling.
>>>>> [  433.902889] xhci_hcd 0000:3a:00.0: xhci_hub_status_data: stopping port polling.
>>>>> [  433.902891] xhci_hcd 0000:3a:00.0: hcd_pci_runtime_resume: 0
>>>>> [  433.902919] usb usb4: usb wakeup-resume
>>>>> [  433.902942] usb usb4: usb auto-resume
>>>>> [  433.902966] hub 4-0:1.0: hub_resume
>>>>> ...
>>>>> 
>>>>> However the warm-reset never success, the asserted PCI PME keeps the
>>>>> runtime-resume, warm-reset and runtime-suspend loop which never bring it back
>>>>> and causing spurious interrupts floods.
>>>>> 
>>>>> After some trial and errors, the issue goes away if LPM on the SMSC hub
>>>>> is disabled. Digging further, enabling and disabling LPM during runtime
>>>>> resume and runtime suspend respectively can solve the issue.
>>>>> 
>>>>> So bring back the old LPM behavior as a quirk and use it for the SMSC
>>>>> hub to solve the issue.
>>>>> 
>>>>> Fixes: d590c2311150 ("usb: Avoid unnecessary LPM enabling and disabling during suspend and resume")
>>>>> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
>>>>> ---
>>>>> v3:
>>>>> - Add forgotten patch revision changelog.
>>>>> 
>>>>> v2:
>>>>> - Explained by Alan, the hub should properly handle U3 -> U0 transition.
>>>>>  So use a quirk to target this buggy device only.
>>>>> 
>>>>> Documentation/admin-guide/kernel-parameters.txt |  3 +++
>>>>> drivers/usb/core/hub.c                          | 15 +++++++++++++++
>>>>> drivers/usb/core/quirks.c                       |  6 ++++++
>>>>> include/linux/usb/quirks.h                      |  3 +++
>>>>> 4 files changed, 27 insertions(+)
>>>> 
>>>> Mathias may want to try something different to fix this problem.  But
>>>> if he doesn't, this patch is okay with me.
>>>> 
>>>> Acked-by: Alan Stern <stern@rowland.harvard.edu>
>>> 
>>> If there's no objection, can we merge this patch?
>> I wanted to have Mathias weigh in on this before merging it...
> 
> This might need some closer inspection still.
> 
> The "Get port status 4-1 read: 0x10202e" means port is not really in compliance mode,
> instead port has CAS (Cold Attach Status) bit set, meaning parts of xHC needed for
> link training were probably still powered off when device was plugged in, so device failed
> to reach a connected, enabled, U0: link state. I needs to be warm reset.

[  433.315239] xhci_hcd 0000:3a:00.0: Get port status 4-1 read: 0x10202e2, return 0x10343
Ok, so we should check 0x10202e2 from xHC here, instead of 0x10343.

> 
> there is no CAS link state in USB3 spec, so xhci driver reports a compliance mode link state
> to usb core instead. Both states are resolved by a warm reset.
> 
> But looks like warm reset is refused as usb device state is still "suspended" in software:
> "usb 4-1: device reset not allowed in state 8"

Thanks for pointing this out. I'll see what's really going on here.

Kai-Heng

> 
> -Mathias