Re: [PATCH v4 06/12] ARM: dove: add gigabit ethernet and mvmdio device tree nodes

From: Jason Cooper <jason@lakedaemon.net>
To: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>,
	Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Andrew Lunn <andrew@lunn.ch>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
	"tiejun.chen" <tiejun.chen@windriver.com>,
	Lennert Buytenhek <buytenh@wantstofly.org>,
	linuxppc-dev@lists.ozlabs.org, David Miller <davem@davemloft.net>,
	linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v4 06/12] ARM: dove: add gigabit ethernet and mvmdio device tree nodes
Date: Wed, 22 May 2013 09:10:10 -0400	[thread overview]
Message-ID: <20130522131010.GB31290@titan.lakedaemon.net> (raw)
In-Reply-To: <519C9A66.3050807@gmail.com>

On Wed, May 22, 2013 at 12:13:58PM +0200, Sebastian Hesselbarth wrote:
> On 05/22/2013 12:04 PM, tiejun.chen wrote:
> >On 05/22/2013 05:43 PM, Sebastian Hesselbarth wrote:
> >>On 05/21/2013 07:48 PM, Andrew Lunn wrote:
> >>>On Tue, May 21, 2013 at 06:41:44PM +0200, Sebastian Hesselbarth wrote:
> >>>>This patch adds orion-eth and mvmdio device tree nodes for DT enabled
> >>>>Dove boards. As there is only one ethernet controller on Dove, a
> >>>>default
> >>>>phy node is also added with a note to set its reg property on a
> >>>>per-board
> >>>>basis.
> >>>>
> >>>>Signed-off-by: Sebastian Hesselbarth<sebastian.hesselbarth@gmail.com>
> >>>>---
> >>...
> >>>>+ ethernet-port@0 {
> >>>>+ device_type = "network";
> >>>>+ compatible = "marvell,orion-eth-port";
> >>>>+ reg =<0>;
> >>>>+ interrupts =<29>;
> >>>>+ /* overwrite MAC address in bootloader */
> >>>>+ local-mac-address = [00 00 00 00 00 00];
> >>>
> >>>Hi Sebastian
> >>>
> >>>Its probably a good idea to set the local administration bit in this
> >>>MAC address. i.e. first byte is 02.
> >>
> >>Andrew,
> >>
> >>we just need an invalid address here to trigger the default behavior of
> >>the driver and load the MAC address from its register. As PPC binding
> >>documentation also has all zero, I just took it.
> >
> >The truth is in PPC case, often we set the real mac address with some
> >variables like 'eth[x]addr' in u-boot prompt, then u-boot will parse
> >that value to fill the dtb. At last the associated driver can get the
> >actual mac address from the dtb. And especially for those older u-boot
> >version, even you have to reset the 'local-mac-address' property in dts
> >directly with the real mac address before generate the dtb since the
> >older u-boot have no this ability to fill dtb again before pass the kernel.
> 
> Tiejun,
> 
> with Marvell SoCs it is no different, except that there is almost no dtb
> support in their u-boot.

iirc, our solution to this was to parse the ATAGs for the mac addr and
update the appended dtb.  This way, module load and unload would work
without loosing the mac address.  I believe Jason Gunthorpe has a patch
to atags_to_fdt() for this...  This should allow us to get rid of the
clocks hack.

thx,

Jason.