[PATCH v12 09/13] arm64: dts: ls1046a: Add serdes nodes

[Sean Anderson <sean.anderson@seco.com>]

This adds nodes for the SerDes devices. They are disabled by default
to prevent any breakage on existing boards.

Signed-off-by: Sean Anderson <sean.anderson@seco.com>
---

(no changes since v10)

Changes in v10:
- Move serdes bindings to SoC dtsi
- Add support for all (ethernet) serdes modes
- Refer to "nodes" instead of "bindings"
- Move compatible/reg first

Changes in v4:
- Convert to new bindings

Changes in v3:
- Describe modes in device tree

Changes in v2:
- Use one phy cell for SerDes1, since no lanes can be grouped
- Disable SerDes by default to prevent breaking boards inadvertently.

 .../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 111 ++++++++++++++++++
 1 file changed, 111 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
index a01e3cfec77f..f6361fafaef7 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
 
 / {
 	compatible = "fsl,ls1046a";
@@ -424,6 +425,116 @@ sfp: efuse@1e80000 {
 			clock-names = "sfp";
 		};
 
+		serdes1: serdes@1ea0000 {
+			compatible = "fsl,ls1046a-serdes", "fsl,lynx-10g";
+			reg = <0x0 0x1ea0000 0x0 0x2000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+
+			/*
+			 * XXX: Lane A uses pins SD1_RX3_P/N! That is, the lane
+			 * numbers and pin numbers are _reversed_. In addition,
+			 * the PCCR documentation is _inconsistent_ in its
+			 * usage of these terms!
+			 *
+			 * PCCR "Lane 0" refers to...
+			 * ==== =====================
+			 *    0 Lane A
+			 *    2 Lane A
+			 *    8 Lane A
+			 *    9 Lane A
+			 *    B Lane D!
+			 */
+			serdes1_A: phy@0 {
+				#phy-cells = <0>;
+				reg = <0>;
+
+				/* SGMII.6 */
+				sgmii-0 {
+					fsl,pccr = <0x8>;
+					fsl,index = <0>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_SGMII>;
+				};
+			};
+
+			serdes1_B: phy@1 {
+				#phy-cells = <0>;
+				reg = <1>;
+
+				/* SGMII.5 */
+				sgmii-1 {
+					fsl,pccr = <0x8>;
+					fsl,index = <1>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_2500BASEX>;
+				};
+
+				/* QSGMII.6,5,10,1 */
+				qsgmii-1 {
+					fsl,pccr = <0x9>;
+					fsl,index = <1>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_QSGMII>;
+				};
+
+				/* TODO: PCIe.1 */
+			};
+
+			serdes1_C: phy@2 {
+				#phy-cells = <0>;
+				reg = <2>;
+
+				/* SGMII.10 */
+				sgmii-2 {
+					fsl,pccr = <0x8>;
+					fsl,index = <2>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_2500BASEX>;
+				};
+
+				/* XFI.10 */
+				xfi-0 {
+					fsl,pccr = <0xb>;
+					fsl,index = <0>;
+					fsl,cfg = <0x2>;
+					fsl,type = <PHY_TYPE_10GBASER>;
+				};
+			};
+
+			serdes1_D: phy@3 {
+				#phy-cells = <0>;
+				reg = <3>;
+
+				/* SGMII.9 */
+				sgmii-3 {
+					fsl,pccr = <0x8>;
+					fsl,index = <3>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_2500BASEX>;
+				};
+
+				/* XFI.9 */
+				xfi-1 {
+					fsl,pccr = <0xb>;
+					fsl,index = <1>;
+					fsl,cfg = <0x1>;
+					fsl,type = <PHY_TYPE_10GBASER>;
+				};
+			};
+		};
+
+		serdes2: serdes@1eb0000 {
+			compatible = "fsl,ls1046a-serdes", "fsl,lynx-10g";
+			reg = <0x0 0x1eb0000 0x0 0x2000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1046a-dcfg", "syscon";
 			reg = <0x0 0x1ee0000 0x0 0x1000>;
-- 
2.35.1.1320.gc452695387.dirty