From: Andy Gross <agross@codeaurora.org>
To: linux-arm-msm@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-usb@vger.kernel.org,
Greg KH <gregkh@linuxfoundation.org>,
devicetree@vger.kernel.org,
Kishon Vijay Abraham I <kishon@ti.com>,
Andy Gross <agross@codeaurora.org>
Subject: [PATCH 3/4] ARM: dts: qcom: Add DWC3 USB support on IPQ8064
Date: Fri, 20 Nov 2015 02:35:08 -0600 [thread overview]
Message-ID: <1448008509-8913-4-git-send-email-agross@codeaurora.org> (raw)
In-Reply-To: <1448008509-8913-1-git-send-email-agross@codeaurora.org>
This patch adds Qualcomm DWC3 USB nodes to device tree to enable support for the
DWC3 controller found on IPQ8064/AP148 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
---
arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 24 +++++++++
arch/arm/boot/dts/qcom-ipq8064.dtsi | 89 ++++++++++++++++++++++++++++++++
2 files changed, 113 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
index d501382..bf1638c 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
@@ -97,5 +97,29 @@
sata@29000000 {
status = "ok";
};
+
+ phy@100f8800 {
+ status = "ok";
+ };
+
+ phy@100f8830 {
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ phy@110f8800 {
+ status = "ok";
+ };
+
+ phy@110f8830 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
};
};
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index fa69863..b2dcd9d 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -329,5 +329,94 @@
#reset-cells = <1>;
};
+ hs_phy_0: phy@100f8800 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ reg = <0x100f8800 0x30>;
+ clocks = <&gcc USB30_0_UTMI_CLK>;
+ clock-names = "ref";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ ss_phy_0: phy@100f8830 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ reg = <0x100f8830 0x30>;
+
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "ref";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb30@0 {
+ compatible = "qcom,dwc3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "core";
+
+ syscon-tcsr = <&tcsr 0xb0 1>;
+
+ ranges;
+
+ status = "disabled";
+
+ dwc3@10000000 {
+ compatible = "snps,dwc3";
+ reg = <0x10000000 0xcd00>;
+ interrupts = <0 205 0x4>;
+ phys = <&hs_phy_0>, <&ss_phy_0>;
+ phy-names = "usb2-phy", "usb3-phy";
+ tx-fifo-resize;
+ dr_mode = "host";
+ };
+ };
+
+ hs_phy_1: phy@110f8800 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ reg = <0x110f8800 0x30>;
+ clocks = <&gcc USB30_1_UTMI_CLK>;
+ clock-names = "ref";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ ss_phy_1: phy@110f8830 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ reg = <0x110f8830 0x30>;
+
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "ref";
+
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ usb30@1 {
+ compatible = "qcom,dwc3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "core";
+
+ syscon-tcsr = <&tcsr 0xb0 0>;
+
+ ranges;
+
+ status = "disabled";
+
+ dwc3@11000000 {
+ compatible = "snps,dwc3";
+ reg = <0x11000000 0xcd00>;
+ interrupts = <0 110 0x4>;
+ phys = <&hs_phy_1>, <&ss_phy_1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ tx-fifo-resize;
+ dr_mode = "host";
+ };
+ };
};
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
next prev parent reply other threads:[~2015-11-20 8:36 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-11-20 8:35 [PATCH 0/4] Add QCOM DWC3 Phy support Andy Gross
2015-11-20 8:35 ` [PATCH 1/4] phy: Add Qualcomm DWC3 HS/SS PHY driver Andy Gross
2015-11-20 8:35 ` [PATCH 2/4] usb: dwc3: qcom: Configure TCSR phy mux register Andy Gross
2015-11-20 15:06 ` Felipe Balbi
2015-11-20 15:54 ` Andy Gross
2015-11-20 8:35 ` Andy Gross [this message]
2015-11-20 8:35 ` [PATCH 4/4] Documentation: usb: dwc3: qcom: Add TCSR mux usage Andy Gross
2015-11-20 14:33 ` Rob Herring
2015-11-20 15:08 ` Felipe Balbi
2015-11-20 15:56 ` Andy Gross
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1448008509-8913-4-git-send-email-agross@codeaurora.org \
--to=agross@codeaurora.org \
--cc=balbi@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).