From: Neil Armstrong <narmstrong@baylibre.com>
To: khilman@baylibre.com, carlo@caione.org
Cc: Neil Armstrong <narmstrong@baylibre.com>,
linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Subject: [PATCH 1/8] ARM64: dts: meson-gxbb: Move common nodes to meson-gx
Date: Mon, 31 Oct 2016 17:44:39 +0100 [thread overview]
Message-ID: <1477932286-27482-2-git-send-email-narmstrong@baylibre.com> (raw)
In-Reply-To: <1477932286-27482-1-git-send-email-narmstrong@baylibre.com>
Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gx.dtsi | 131 ++++++++++++++++++++++++
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 153 ++++------------------------
2 files changed, 148 insertions(+), 136 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
index fd1d0de..91be4f2 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -129,6 +129,30 @@
#clock-cells = <0>;
};
+ firmware {
+ sm: secure-monitor {
+ compatible = "amlogic,meson-gx-sm", "amlogic,meson-gxbb-sm";
+ };
+ };
+
+ efuse: efuse {
+ compatible = "amlogic,meson-gx-efuse", "amlogic,meson-gxbb-efuse";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sn: sn@14 {
+ reg = <0x14 0x10>;
+ };
+
+ eth_mac: eth_mac@34 {
+ reg = <0x34 0x10>;
+ };
+
+ bid: bid@46 {
+ reg = <0x46 0x30>;
+ };
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
@@ -142,6 +166,12 @@
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+ reset: reset-controller@4404 {
+ compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
uart_A: serial@84c0 {
compatible = "amlogic,meson-uart";
reg = <0x0 0x84c0 0x0 0x14>;
@@ -149,6 +179,76 @@
clocks = <&xtal>;
status = "disabled";
};
+
+ uart_B: serial@84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ i2c_A: i2c@8500 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x08500 0x0 0x20>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ pwm_ab: pwm@8550 {
+ compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08550 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_cd: pwm@8650 {
+ compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x08650 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ pwm_ef: pwm@86c0 {
+ compatible = "amlogic,meson-gx-pwm", "amlogic,meson-gxbb-pwm";
+ reg = <0x0 0x086c0 0x0 0x10>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart_C: serial@8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ i2c_B: i2c@87c0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087c0 0x0 0x20>;
+ interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ i2c_C: i2c@87e0 {
+ compatible = "amlogic,meson-gxbb-i2c";
+ reg = <0x0 0x087e0 0x0 0x20>;
+ interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ watchdog@98d0 {
+ compatible = "amlogic,meson-gx-wdt", "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0x098d0 0x0 0x10>;
+ clocks = <&xtal>;
+ };
};
gic: interrupt-controller@c4301000 {
@@ -178,6 +278,13 @@
clocks = <&xtal>;
status = "disabled";
};
+
+ ir: ir@580 {
+ compatible = "amlogic,meson-gxbb-ir";
+ reg = <0x0 0x00580 0x0 0x40>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
+ status = "disabled";
+ };
};
periphs: periphs@c8834000 {
@@ -186,6 +293,11 @@
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8834000 0x0 0x2000>;
+
+ rng {
+ compatible = "amlogic,meson-rng";
+ reg = <0x0 0x0 0x0 0x4>;
+ };
};
@@ -195,6 +307,25 @@
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+
+ mailbox: mailbox@404 {
+ compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
+ reg = <0 0x404 0 0x4c>;
+ interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
+ <0 209 IRQ_TYPE_EDGE_RISING>,
+ <0 210 IRQ_TYPE_EDGE_RISING>;
+ #mbox-cells = <1>;
+ };
+ };
+
+ ethmac: ethernet@c9410000 {
+ compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
+ reg = <0x0 0xc9410000 0x0 0x10000
+ 0x0 0xc8834540 0x0 0x4>;
+ interrupts = <0 8 1>;
+ interrupt-names = "macirq";
+ phy-mode = "rgmii";
+ status = "disabled";
};
apb: apb@d0000000 {
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 2d69a3b..160664f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -50,30 +50,6 @@
/ {
compatible = "amlogic,meson-gxbb";
- firmware {
- sm: secure-monitor {
- compatible = "amlogic,meson-gxbb-sm";
- };
- };
-
- efuse: efuse {
- compatible = "amlogic,meson-gxbb-efuse";
- #address-cells = <1>;
- #size-cells = <1>;
-
- sn: sn@14 {
- reg = <0x14 0x10>;
- };
-
- eth_mac: eth_mac@34 {
- reg = <0x34 0x10>;
- };
-
- bid: bid@46 {
- reg = <0x46 0x30>;
- };
- };
-
scpi {
compatible = "amlogic,meson-gxbb-scpi";
mboxes = <&mailbox 1 &mailbox 2>;
@@ -158,20 +134,6 @@
dr_mode = "host";
status = "disabled";
};
-
- ethmac: ethernet@c9410000 {
- compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
- reg = <0x0 0xc9410000 0x0 0x10000
- 0x0 0xc8834540 0x0 0x4>;
- interrupts = <0 8 1>;
- interrupt-names = "macirq";
- clocks = <&clkc CLKID_ETH>,
- <&clkc CLKID_FCLK_DIV2>,
- <&clkc CLKID_MPLL2>;
- clock-names = "stmmaceth", "clkin0", "clkin1";
- phy-mode = "rgmii";
- status = "disabled";
- };
};
};
@@ -192,55 +154,6 @@
};
&cbus {
- reset: reset-controller@4404 {
- compatible = "amlogic,meson-gxbb-reset";
- reg = <0x0 0x04404 0x0 0x20>;
- #reset-cells = <1>;
- };
-
- uart_B: serial@84dc {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84dc 0x0 0x14>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- pwm_ab: pwm@8550 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x08550 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- pwm_cd: pwm@8650 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x08650 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- pwm_ef: pwm@86c0 {
- compatible = "amlogic,meson-gxbb-pwm";
- reg = <0x0 0x086c0 0x0 0x10>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- uart_C: serial@8700 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x8700 0x0 0x14>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- watchdog@98d0 {
- compatible = "amlogic,meson-gxbb-wdt";
- reg = <0x0 0x098d0 0x0 0x10>;
- clocks = <&xtal>;
- };
-
spifc: spi@8c80 {
compatible = "amlogic,meson-gxbb-spifc";
reg = <0x0 0x08c80 0x0 0x80>;
@@ -249,36 +162,13 @@
clocks = <&clkc CLKID_SPI>;
status = "disabled";
};
+};
- i2c_A: i2c@8500 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x08500 0x0 0x20>;
- interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- i2c_B: i2c@87c0 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x087c0 0x0 0x20>;
- interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
- i2c_C: i2c@87e0 {
- compatible = "amlogic,meson-gxbb-i2c";
- reg = <0x0 0x087e0 0x0 0x20>;
- interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_I2C>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
+ðmac {
+ clocks = <&clkc CLKID_ETH>,
+ <&clkc CLKID_FCLK_DIV2>,
+ <&clkc CLKID_MPLL2>;
+ clock-names = "stmmaceth", "clkin0", "clkin1";
};
&aobus {
@@ -355,13 +245,6 @@
#reset-cells = <1>;
};
- ir: ir@580 {
- compatible = "amlogic,meson-gxbb-ir";
- reg = <0x0 0x00580 0x0 0x40>;
- interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
- status = "disabled";
- };
-
pwm_ab_AO: pwm@550 {
compatible = "amlogic,meson-gxbb-pwm";
reg = <0x0 0x0550 0x0 0x10>;
@@ -381,11 +264,6 @@
};
&periphs {
- rng {
- compatible = "amlogic,meson-rng";
- reg = <0x0 0x0 0x0 0x4>;
- };
-
pinctrl_periphs: pinctrl@4b0 {
compatible = "amlogic,meson-gxbb-periphs-pinctrl";
#address-cells = <2>;
@@ -593,15 +471,18 @@
#clock-cells = <1>;
reg = <0x0 0x0 0x0 0x3db>;
};
+};
- mailbox: mailbox@404 {
- compatible = "amlogic,meson-gxbb-mhu";
- reg = <0 0x404 0 0x4c>;
- interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
- <0 209 IRQ_TYPE_EDGE_RISING>,
- <0 210 IRQ_TYPE_EDGE_RISING>;
- #mbox-cells = <1>;
- };
+&i2c_A {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_B {
+ clocks = <&clkc CLKID_I2C>;
+};
+
+&i2c_C {
+ clocks = <&clkc CLKID_I2C>;
};
&sd_emmc_a {
--
1.9.1
next prev parent reply other threads:[~2016-10-31 16:47 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-31 16:44 [PATCH 0/8] ARM64: dts: meson-gxl: Add extended support Neil Armstrong
2016-10-31 16:44 ` Neil Armstrong [this message]
2016-10-31 16:44 ` [PATCH 2/8] ARM64: dts: meson-gxl: Add pinctrl nodes Neil Armstrong
2016-11-07 22:30 ` Kevin Hilman
2016-10-31 16:44 ` [PATCH 3/8] ARM64: dts: meson-gxl: Add clock nodes Neil Armstrong
2016-10-31 16:44 ` [PATCH 4/8] ARM64: dts: meson-gxl: Add i2c nodes Neil Armstrong
2016-10-31 16:44 ` [PATCH 5/8] ARM64: dts: meson-gxl: Add MMC/SD/SDIO nodes Neil Armstrong
2016-10-31 16:44 ` [PATCH 6/8] ARM64: dts: meson-gxl-p23x: Add uart pinctrl Neil Armstrong
2016-10-31 16:44 ` [PATCH 7/8] ARM64: dts: meson-gxl-p23x: Add SD/SDIO/MMC and PWM nodes Neil Armstrong
2016-11-05 22:10 ` Kevin Hilman
2016-10-31 16:44 ` [PATCH 8/8] ARM64: dts: meson-gxl-p23x: Enable IR receiver Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1477932286-27482-2-git-send-email-narmstrong@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).