From: Nagarjuna Kristam <nkristam@nvidia.com>
To: <balbi@kernel.org>, <gregkh@linuxfoundation.org>,
<thierry.reding@gmail.com>, <jonathanh@nvidia.com>,
<mark.rutland@arm.com>, <robh+dt@kernel.org>, <kishon@ti.com>
Cc: <devicetree@vger.kernel.org>, <linux-tegra@vger.kernel.org>,
<linux-usb@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Nagarjuna Kristam <nkristam@nvidia.com>
Subject: [PATCH 07/18] phy: tegra: xusb: Add set_mode support for utmi phy on Tegra186
Date: Fri, 6 Dec 2019 16:20:10 +0530 [thread overview]
Message-ID: <1575629421-7039-8-git-send-email-nkristam@nvidia.com> (raw)
In-Reply-To: <1575629421-7039-1-git-send-email-nkristam@nvidia.com>
Add support for set_mode on utmi phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
---
drivers/phy/tegra/xusb-tegra186.c | 109 ++++++++++++++++++++++++++++++--------
1 file changed, 87 insertions(+), 22 deletions(-)
diff --git a/drivers/phy/tegra/xusb-tegra186.c b/drivers/phy/tegra/xusb-tegra186.c
index 84c2739..9a45160 100644
--- a/drivers/phy/tegra/xusb-tegra186.c
+++ b/drivers/phy/tegra/xusb-tegra186.c
@@ -301,6 +301,92 @@ static void tegra_phy_xusb_utmi_pad_power_down(struct phy *phy)
tegra186_utmi_bias_pad_power_off(padctl);
}
+static int tegra186_xusb_padctl_vbus_override(struct tegra_xusb_padctl *padctl,
+ bool status)
+{
+ u32 value;
+
+ dev_dbg(padctl->dev, "%s vbus override\n", status ? "set" : "clear");
+
+ value = padctl_readl(padctl, USB2_VBUS_ID);
+
+ if (status) {
+ value |= VBUS_OVERRIDE;
+ value &= ~ID_OVERRIDE(~0);
+ value |= ID_OVERRIDE_FLOATING;
+ } else {
+ value &= ~VBUS_OVERRIDE;
+ }
+
+ padctl_writel(padctl, value, USB2_VBUS_ID);
+
+ return 0;
+}
+
+static int tegra186_xusb_padctl_id_override(struct tegra_xusb_padctl *padctl,
+ bool status)
+{
+ u32 value;
+
+ dev_dbg(padctl->dev, "%s id override\n", status ? "set" : "clear");
+
+ value = padctl_readl(padctl, USB2_VBUS_ID);
+
+ if (status) {
+ if (value & VBUS_OVERRIDE) {
+ value &= ~VBUS_OVERRIDE;
+ padctl_writel(padctl, value, USB2_VBUS_ID);
+ usleep_range(1000, 2000);
+
+ value = padctl_readl(padctl, USB2_VBUS_ID);
+ }
+
+ value &= ~ID_OVERRIDE(~0);
+ value |= ID_OVERRIDE_GROUNDED;
+ } else {
+ value &= ~ID_OVERRIDE(~0);
+ value |= ID_OVERRIDE_FLOATING;
+ }
+
+ padctl_writel(padctl, value, USB2_VBUS_ID);
+
+ return 0;
+}
+
+static int tegra186_utmi_phy_set_mode(struct phy *phy, enum phy_mode mode,
+ int submode)
+{
+ struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
+ struct tegra_xusb_padctl *padctl = lane->pad->padctl;
+ struct tegra_xusb_usb2_port *port = tegra_xusb_find_usb2_port(padctl,
+ lane->index);
+ int err = 0;
+
+ mutex_lock(&padctl->lock);
+
+ dev_dbg(&port->base.dev, "%s: mode %d", __func__, mode);
+
+ if (mode == PHY_MODE_USB_OTG) {
+ if (submode == USB_ROLE_HOST) {
+ tegra186_xusb_padctl_id_override(padctl, true);
+
+ err = regulator_enable(port->supply);
+ } else if (submode == USB_ROLE_DEVICE) {
+ tegra186_xusb_padctl_vbus_override(padctl, true);
+ } else if (submode == USB_ROLE_NONE) {
+ if (regulator_is_enabled(port->supply))
+ regulator_disable(port->supply);
+
+ tegra186_xusb_padctl_id_override(padctl, false);
+ tegra186_xusb_padctl_vbus_override(padctl, false);
+ }
+ }
+
+ mutex_unlock(&padctl->lock);
+
+ return err;
+}
+
static int tegra186_utmi_phy_power_on(struct phy *phy)
{
struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
@@ -439,6 +525,7 @@ static const struct phy_ops utmi_phy_ops = {
.exit = tegra186_utmi_phy_exit,
.power_on = tegra186_utmi_phy_power_on,
.power_off = tegra186_utmi_phy_power_off,
+ .set_mode = tegra186_utmi_phy_set_mode,
.owner = THIS_MODULE,
};
@@ -857,28 +944,6 @@ static void tegra186_xusb_padctl_remove(struct tegra_xusb_padctl *padctl)
{
}
-static int tegra186_xusb_padctl_vbus_override(struct tegra_xusb_padctl *padctl,
- bool status)
-{
- u32 value;
-
- dev_dbg(padctl->dev, "%s vbus override\n", status ? "set" : "clear");
-
- value = padctl_readl(padctl, USB2_VBUS_ID);
-
- if (status) {
- value |= VBUS_OVERRIDE;
- value &= ~ID_OVERRIDE(~0);
- value |= ID_OVERRIDE_FLOATING;
- } else {
- value &= ~VBUS_OVERRIDE;
- }
-
- padctl_writel(padctl, value, USB2_VBUS_ID);
-
- return 0;
-}
-
static const struct tegra_xusb_padctl_ops tegra186_xusb_padctl_ops = {
.probe = tegra186_xusb_padctl_probe,
.remove = tegra186_xusb_padctl_remove,
--
2.7.4
next prev parent reply other threads:[~2019-12-06 10:51 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-06 10:50 [PATCH 00/18] Tegra XUSB OTG support Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 01/18] dt-bindings: phy: tegra-xusb: Add usb-role-switch Nagarjuna Kristam
2019-12-06 14:49 ` Thierry Reding
2019-12-09 4:45 ` Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 02/18] dt-bindings: usb: Add NVIDIA Tegra XUSB device mode controller binding Nagarjuna Kristam
2019-12-13 18:45 ` Rob Herring
2019-12-16 6:30 ` Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 03/18] phy: tegra: xusb: Add usb-role-switch support Nagarjuna Kristam
2019-12-06 14:54 ` Thierry Reding
2019-12-10 3:52 ` Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 04/18] phy: tegra: xusb: Add usb-phy support Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 05/18] phy: tegra: xusb: Add support to get companion USB 3 port Nagarjuna Kristam
2019-12-06 14:57 ` Thierry Reding
2019-12-09 6:27 ` Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 06/18] phy: tegra: xusb: Add set_mode support for USB 2 phy on Tegra210 Nagarjuna Kristam
2019-12-06 10:50 ` Nagarjuna Kristam [this message]
2019-12-06 10:50 ` [PATCH 08/18] usb: xhci-tegra: Add OTG support Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 09/18] usb: gadget: tegra-xudc: Remove usb-role-switch support Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 10/18] usb: gadget: tegra-xudc: Add usb-phy support Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 11/18] usb: gadget: tegra-xudc: use phy_set_mode to set/unset device mode Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 12/18] usb: gadget: tegra-xudc: support multiple device modes Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 13/18] arm64: tegra: update OTG port entries for jetson-tx1 Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 14/18] arm64: tegra: update OTG port entries for jetson-tx2 Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 15/18] arm64: tegra: Add xudc node for Tegra210 Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 16/18] arm64: tegra: Enable xudc on Jetson TX1 Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 17/18] arm64: tegra: Add xudc node for Tegra186 Nagarjuna Kristam
2019-12-06 10:50 ` [PATCH 18/18] arm64: tegra: Enable xudc node on Jetson TX2 Nagarjuna Kristam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1575629421-7039-8-git-send-email-nkristam@nvidia.com \
--to=nkristam@nvidia.com \
--cc=balbi@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jonathanh@nvidia.com \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).